Specifications - hubbellcdn

1 Specifications / / /Pole Mounting Structural Luminiare Finish OptionSee page 2 See page 3 Conduit OpeningPresswoodTemplateBase SizeLongitudinalreference parallelto curb or ViewBolt CircleDiameter45 Leveling Nutand WasherConcrete footing to be designed by DetailAnchor BoltProjectionGrout must be packed under pole base to insure full contact with footing and prevent loosening of leveling a channel through the grout for drainage from the pole Bolt Cover, :48' and 50' poles are ArmMountingPost TopMountingHandholeBoltCoversSee charton page "ZPole Construction: Tapered by spinning and coldworking a seamless one-piece extruded tube of aluminum alloy 6063-T4. After tapering, shaft is welded to a cast aluminum anchor base of alloy A356, heat-treated to T-6 temper, and rotary sand finished. Poles above 39' include a flush field joint approximately 26K' above base, with both sections taper Covers: Cast aluminum anchor bolt covers Cap: A flush-sided cast aluminum pole cap is provided for side arm mounted : Reinforced handhole with a gasketed cover and grounding provisions provided, 18" up from base.

2 Cover mounts Bolts: Four galvanized anchor bolts provided, complete with eight nuts, eight flat washers, and a presswood Dampener: Poles 20' and above include a mechanically fastened internal pendulum vibration : Poles will withstand wind loads as listed in chart (see page 2) when luminaires are mounted per fixture installation : Super TGIC thermoset polyester powder coat paint applied over a titanated zirconium conversion coating. Standard colors are Black, Dark Bronze, Light Gray, Graphite Platinum Silver, Titanium and White. Custom colors are : Installation of poles without luminaire(s) will compromise pole strength. Any accessories attached to pole, or other modifications will compromise pole strength and may result in pole : A regularly scheduled maintenance program must be established to insure the protective paint coating is intact, corrosion or structural damage has not occurred, and anchor bolt nuts are tight.

3 Failure to do so could lead to pole collapse and serious personal : Certified UL 1598 in accordance with Article 410 of ANSI NFPA 70, National Electrical Code. Complies with the CSA standard. Note: If a UL or CSA label is required, a request must be made at time of order. Approvals:Type:Job:Catalog number:Date:Page: 1 of 4 2015 KIM LIGHTING 16555 EAST GALE AVENUE, CITY OF INDUSTRY, CA 91745-1788 TEL: 626/968-5666 FAX: 626/968-5716 LTRAR ound Aluminum Tapered Polerevision 10/8/15 2015 KIM LIGHTING 16555 EAST GALE AVENUE, CITY OF INDUSTRY, CA 91745-1788 TEL: 626/968-5666 FAX: 626/968-571648' and 50' poles are 2-piece assembliesStandard FeaturesNOTE: All allowable pole and fixture EPAs are derived from the AASHTO standard. Responsibility lies with the specifier for correct pole selection based on local codes and standards for the job location.

4 (See page 4). Wind Map Steady WindPole Catalog X Y Z Number 85 90 100 110 120 130 140 150l LTRA16-6156 16' 6" x .156 4" LTRA16-6188 16' 6" x .188 4" LTRA20-5156 20' 5" x .156 3" LTRA20-5188 20' 5" x .188 3" LTRA20-6156 20' 6" x .156 4" LTRA20-6188 20' 6" x .188 4" LTRA25-6156 25' 6" x .156 4" LTRA25-6188 25' 6" x .188 4" LTRA25-7156 25' 7" x .156 4" LTRA25-8156 25' 8" x .156 4K" LTRA30-7156 30' 7" x.

5 156 4" LTRA30-8156 30' 8" x .156 4K" l LTRA30-8188 30' 8" x .188 4K" LTRA30-8250 30' 8" x .250 4K" LTRA35-8156 35' 8" x .156 4K" LTRA35-8188 35' 8" x .188 4K" LTRA35-8250 35' 8" x .250 4K" LTRA35-10188 35' 10" x .188 6" LTRA39-8188 39' 8" x .188 4K" LTRA39-8250 39' 8" x .250 4K" LTRA39-10188 39' 10" x .188 6" LTRA39-10250 39' 10" x .250 6" LTRA48-10250 48' 10" x .250 6" LTRA50-10250 50' 10" x .250 6" ---PoleAllowable Pole EPA Bolt Anchor Anchor Pole Y Pole Circle Bolt Bolts Base Conduit Height Diameter DIA Projection Size Size Opening20' 5" 9K" 3J" L" x 30" + 4" " sq.

6 4K" DIA 16'-25' 6" 9K" 3J" L" x 30" + 4" " sq. 5" DIA 25' - 30' 7" 11" 3K" 1" x 36" + 4" " sq. 6K" DIA25' - 39' 8" 11K" 3K" 1" x 36" + 4" " sq. 7K" DIA35' - 48' 10" 14L" 4L" 1" x 48" + 4" " sq. 9K" DIA50' 10" 14L" 4L" 1J" x 42" + 6" " sq. 9K" DIAA nchor Base and Bolt DetailXYZ18"HandholeBoltCoversLTRAR ound Aluminum Tapered Polerevision 10/8/15 : 2 of 4 Type:Job:FinishStandard thermoset polyester powder coat paint over titanated zirconium conversion coating. 2015 KIM LIGHTING 16555 EAST GALE AVENUE, CITY OF INDUSTRY, CA 91745-1788 TEL: 626/968-5666 FAX: 626/968-5716 Standard FeaturesColor: Black Dark Bronze Light Gray Graphite Platinum Silver Titanium White Custom Color1 Cat.

7 No.: l BL l DB l LG l GT l PS l l TT l WH l CC11 Custom color subject to additional charges, minimum quantities and extended lead times. Consult representative. Custom color description:Mounting Side ArmPlan Views:FlushMount!Mounting1: l FM l A l SA l B l SB l L l SL l T l ST l Y l SY l C l SCLTRAR ound Aluminum Tapered Polerevision 10/8/15 : 3 of 4 Type:Job:NOTE: Allowable Pole EPA for jobsite wind conditions must be equal to or greater than fixture mount EPA. Please refer to Kim luminaire catalog for specific luminaire drilling requirements in luminaire catalog.)Structural Luminaires Only - Examplesl TS: Single Tension for small and large Structural - LTRA20-5156B-TSl TD: Double Tension for small and large Structural - LTRA20-5156B-TDl TR: Truss for small and large Structural - LTRA20-5156B-TRl XTS: Single Tension for 1000W Structural - LTRA20-5156B-XTSl XTD: Double Tension for 1000W Structural - LTRA20-5156B-XTDl XTR: Truss for 1000W Structural - LTRA20-5156B-XTR 2015 KIM LIGHTING 16555 EAST GALE AVENUE, CITY OF INDUSTRY, CA 91745-1788 TEL: 626/968-5666 FAX: 626/968-5716 LTRAR ound Aluminum Tapered Polerevision 10/8/15 : Values are based on 50 year mean recurrence interval 30' above grade.

8 Hawaii has an 105 mph wind velocity. Puerto Rico has a 125 mph wind velocity. Caution must be exercised in determining wind velocities in special wind areas such as:Mountainous RegionsAreas surrounding the Great Lakes or other large bodies of water or open subject to extreme wind conditions, such as hurricanes, typhoons, cyclones, and adjacent to specific area with a known or suspected abnormally high intermittent wind condition caused by geography, adjacent structures, or other specific local conditions that may not be recorded in National Weather Service records. Allowable pole EPA for jobsite wind conditions must be equal to or greater than fixture EPA. Responsibility lies with the specifier for correct pole selection based on AASHTO wind map and job location. The Wind Map is intended only as a general guide. Always consult local authorities to determine maximum wind velocities, gusting and unique wind conditions for each specific application.

9 CAUTION: Wind speeds and listed EPAs are for ground mounted installations. Poles mounted on structures (such as bridges and buildings) must consider vibration and coefficient of height factors beyond this general guide. Consult AASHTO standards. Extreme Wind Events: Hurricanes, Typhoons, Cyclones, or Tornadoes expose poles to flying debris, wind shear, and other unpredictable aerodynamic forces not indicated by the wind velocity ratings. Pole Strength Limited Warranty: Standard, unmodified Kim lighting Poles installed as recommended, undamaged by corrosion, or lack of maintenance, shall withstand steady wind conditions as provided on page 2 (Allowable Pole EPA). Installation of poles without luminaires, or attachment of any unauthorized accessories to poles shall void this : 4 of 4 Type:Job:859090100110120130130140140140 15015014013012011010090 Special Wind Region(Consult Local Authorities)90 Wind MapUnited States and CanadaTo obtain more information on AASHTO Standards for Lighting Equipment contact:American Association of State Highway and Transportation Officials:444 N.

10 Capitol Street, NW, Suite 249 Washington, DC 20001(202) 624-5800