Example: tourism industry
Speed Control of DC Motors: the speed of a motor is given ...
traction. The number of series filed turns in the circuit can be changed. With full field, the motor runs at its minimum speed which can be raised ... Rheostatic or Dynamic Braking: In this method, the armature of the shunt motor is disconnected from the supply and is connected across a variable resistance R. The field winding is left connected
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
10. Starting Method for Induction Motors
uotechnology.edu.iq10. Starting Method for Induction Motors A 3-phase induction motor is theoretically self starting. ... Therefore, 3-phase induction motors employ a starting ... In this method a single stator winding is divided into few coil groups. The terminals of all these groups are brought out.
Introduction to Process Control
uotechnology.edu.iq•We assume that its mass flow rate w1 is constant, but the mass fraction of A, x1, varies with time. •Stream 2 consists of pure A and thus x2 = 1. •The mass flow rate of Stream 2, w2, can be manipulated using a control valve. •The mass fraction of A in the exit stream is denoted by x and the desired value (set point) by Xsp.
SCOPE OF OPERATIONS MANAGEMENT
uotechnology.edu.iqOperations Management concern with the conversion of inputs into outputs, using physical resources, so as to provide the desired utilities to the customer while meeting the other organizational objectives of effectiveness, efficiency and adoptability. It distinguishes itself from
Design & Simulation of Electro-Pneumatic System Using PLC ...
uotechnology.edu.iqElectro-pneumatic also used for remotely controlled system where a few sensors are added to assure the safe operation [17]. 2.2 Applications:-There are so many industry application of electro pneumatic system, these applications can be divided into:- 1. Temperature control [5]. 2. Transportation (cement powder, grain and other materials) [6].
Mineral Processing Plant Design
uotechnology.edu.iqImportance of Good Plant Design and in Time Commissioning A good plant design can minimize capital expenditure and maximize on long ... The fundamental goal for the design of a crushing plant is an installation that meets the required production requirements, ... and maintenance personnel, equipment manufacturers, and the engineering consultant ...
1. CAD/CAM Technology
uotechnology.edu.iqgaining speed. CAD Technology = Design Techniques + Computers. The CAD Process is the subset of the Design process. ... Digitizers: Digitizers are used to trace a sketch or other 2-D entities by moving a cursor over a flat surface (which contains the sketch). The position
Biomaterials- Chapter One
uotechnology.edu.iqChapter One Introduction ١ Biomaterials Biomaterials are used to make devices to replace a part or a function of the body in ... surgery, thoracic and cardiovascular surgery, veterinary medicine and surgery, etc. ... bond certain drugs to the biodegradable material, when these materials are …
Building Construction - University of Technology, Iraq
uotechnology.edu.iqinvestigation report on trial pits. The popular methods are: 7 a. Direct remove: It’s the cheaper one and done by making trenches at lowest level of excavated pits and their sides and leave the water to accumulate by slopes away from the pits. b. Pumping remove:
11. Diode Equivalence Circuits
uotechnology.edu.iqFundamentals of Electronic Circuit Design First Class AND gate: is such that the output voltage level is will be 1 if both inputs are a 1. Example 2: Determine the output level for the positive logic AND gate of fig: With 10v at the cathode D1 , is assumed that D1 is in the off state. D2 is assumed to be in the on state due to the low voltage at the cathode side and the
QBasic Expressions
uotechnology.edu.iqString Constants . a string consists of a sequ. ence of characters enclosed in double quote marks. strings usually consist of names or address or cities such as "Computer", "Baghdad". Variables In QBASIC . Again Variables in QBASIC division into two types: 1. Numeric Variables: the variables used to represent numbers are the letters of the