Transcription of SSR ULTRA-PLUS COOLANT - Petropoulos
1 TECHNICAL DATAT ypical Properties of ultra PlusSynthetic Compressor LubricantPropertyTest MethodPerformanceSAE Viscosity ClassificationJ300 SAE10/20 ISO Viscosity ClassificationASTM D242232 Viscosity IndexD2270150 Viscosity, cSt (SUS)at 40 100 0 FD4451100at -40 CD44513,800 Pour Point, F ( C)D97-59 (-51)Flash Point, F ( C)D92263 (128)Auto Ignition Temperature, F ( C)E659424 (218)Conradson Carbon Residue, %D189< Strip Corrosion, 3 hrs @ 212 F/100 CD1301a4-Ball Wear, 40kg, 1 hr, 1800 rpm, (mm) Point, kgD2783100 Evaporation Loss hrs @ 400 Gravity Metal Corrosion (Rust Test)Distilled WaterD665 ApassSynthetic Sea WaterD665 BpassFoam Tendency (Sequence I, II, III)Sequence ID892 NilSequence mlSequence IIID892 NilTotal Acid Pressure Oxidation Test (hr) Heat, cal/gm/ Cat 185 F (btu/lb mol F) Conductivity, cal/(cm)(sec)( C)at 150 -5at 200 250 @ 130 F (54 C) ml oil/emulsion (min) D140141-39-0 (35)SSR ULTRA-PLUS COOLANTT echnical DataIngersoll-Rand CompanyAir Solutions Group800-C Beaty StreetDavidson, NC 28036 2001 Ingersoll-Rand Company Form SCD-964 Printed in USA05515184 MORE THAN AIR.
2 Solutions: compressors are not designed, intended or approved for breathing air applications. Ingersoll-Rand does not approvespecialized equipment for breathing air applications and assumes no responsibility or liability for compressors used for breathing air contained on these pages is intended to extend any warranty or representation, expressed or implied, regarding the productdescribed herein. Any such warranties or other terms and conditions of sale of products shall be in accordance with Ingersoll-Rand sstandard terms and conditions of sale for such products, which are available upon :Please refer to the Material Safety Data Sheetfor ultra plus (Form APDD-772).COMPATIBILITY:The following lists serve as a guide for thematerial compatibility of various seals,plastics, and paints with ultra plus *.ACCEPTABLE:Seals:Fluorocarbon (Viton ), High Nitrile Buna-N, Florosilicone Rubber, Polysulfide, Hytrel , Kalrez , CPMP lastics:Nylon, Teflon , Deltrin , Celcon , PBT, HD-PPE, Ryton (oil-less)Paints:Epoxy, Baked Phenolic, 2-Comp Urethane, MC-Urethane, Oil-Resistant AlkydAPPLICATION DEPENDENT:Seals:Med Nitrile Buna-N, Polyurethane, EPDM, Epichlorohydrin, Polyacrylate Rubber, Silicone RubberPlastics:Polyurethane, Polyethylene, Noryl , Lexan , Lucite , Polysulfone, Polycarbonate (type)Paints:Alkyds, Phenolic, SC-Urethane, Industrial LatexNOT RECOMMENDED:Seals:Neoprene, Natural Rubber, SBR, Buna-S, Butyl Rubber, Chlorosulfonated polyethylene, Low Nitrile Buna-NPlastics:Polystyrene, PVC, ABSP aints:Acrylic, Latex (household), Vinyl, Varnish, Lacquer*Under normal circumstances.
3 In extremeconditions, such as high temperatures (over 250 F) and/or high stress, compatibilityshould be :In the case of employment of new sealcomposition, lubricant compatibility should beevaluated. Please refer to Ingersoll-RandContract Service, Davidson, North Carolina.
