Transcription of Standard SWRO T M 8 0 0 C - Toray Membrane America
1 Standard SWROT M 8 0 0 CTM810C4 73(7) ,200( )31TM820C-4008 400(37) ,500( )341. Membrane TypeCross Linked Fully Aromatic Polyamide Composite2. Test ConditionsFeed Water PressureFeed Water TemperatureFeed Water ConcentrationRecovery RateFeed Water pH800 psi( )77 F(25 C)32,000 mg/l Nacl8%73. Minimum Salt Minimum Product Flow Rate1,000gpd( )(TM810C)5,200gpd( )(TM820C-400)5. Boron Rejection(typical value) 93% at pH 8 (5mg/l Boron added to Feed water)Type DiameterInchMembrane Areaft2(m2)Salt Rejection%Product Flow Rategpd(m3/ d)Feed Spacer ThicknessmilDimensionsAll dimensions shown in Inches (millimeter).TM820C-400 Feed WaterConcentrated BrineFB40(1,016)Flow (29) (201) (26) (19)4(101)40(1,016)Flow directionPERMEATEBBFFTM810 COperating the recommended design range, please consult the latest Toray technical bulletin, design guidelines,computer design program, and/ or call an application specialist.
2 If the operating limits givenin this Product Information Bulletin are not strictly followed, the Limited Warranty will be null and All elements are wet tested, treated with tested feed water solution, and then vacuum packed inoxygen barrier bags with deoxidant inside. To prevent biological growth during system shutdown,it is recommended to perform 30-60 minutes flushing of Toray elements with seawater once in everytwo presence of free chlorine and other oxidizing agents under certain conditions, such as heavy metalswhich acts as oxidation catalyst in the feed water will cause unexpected oxidation of the Membrane . It isstrongly recommended to remove these oxidizing agents contained in feed water before operating ROsystem.
3 4. Permeate from the first hour of operation shall be customer is fully responsible for the effects of chemicals that are incompatible with the use will void the element Limited accepts no responsibility for results obtained by the application of this information or the safety or suitability of Toray 's products, either alone or in combination with other products. Users are advised to make their own tests to determine the safety and suitability of each product combination for their own data may change without prior notice, due to technical modifications or production 2014 Maximum Operating PressureMaximum Feed Water Temperature Maximum Feed Water SDI15 Feed Water Chlorine ConcentrationFeed Water pH Range, Continuous OperationFeed Water pH Range, Chemical CleaningMaximum Pressure Drop per ElementMaximum Pressure Drop per Vessel1200psi ( MPa)113 F (45 C)5 Not detectable2-111-1215 psi ( MPa)50 psi ( MPa)Operating InformationNoticeAsia and Oceania: Toray Industries, Membrane Products Department1-1, Nihonbashi muromachi 2-chomeChuo-ku, Tokyo 103-8666, JapanTel.
4 +81 3 3245 4540 Fax: +81 3 3245 4913http:/ / : Toray Membrane USA, Office13435 Danielson St,Poway, CA 92064, USATel: +1 858 218 2390 Fax: +1 858 486 3063 Europe, Middle East and Africa: Toray Membrane Europe AGGrabenackerstrasse 8CH-4142 M nchenstein 1, SwitzerlandTel: +41 61 415 87 10 Fax: +41 61 415 87 20 CHINA: Toray BlueStar Membrane Co., Anxiang Street, Area B,Beijing Tianzhu Airport Economic Development Zone,Beijing ,101318 : +86 10 80490552 Fax: +86 10 80485217
