Example: tourism industry
Surface Moisture-Density Gauge
Using direct transmission or backscattered gamma radiation, the 3430 gauge determines the density of materials by counting the number of photons emitted by a cesium-137 source. Geiger-Mueller (G-M) detectors located in the gauge base detect the gamma radiation and a microprocessor converts the counts into a density reading.
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
Surface Moisture-Density Gauge - Troxler Labs
www.troxlerlabs.comManual of Operation and Instruction Model 3430 (and Model 3430-M) Surface Moisture-Density Gauge Troxler Electronic Laboratories, Inc. 3008 Cornwallis Rd. • …
TROXLER APPLICATION BRIEF - troxlerlabs.com
www.troxlerlabs.comAB3440-0907v2 1 Application Brief . TROXLER MODEL 3440 . Roadreader Nuclear Moisture Density Gauge . September 2007 . Introduction . The Troxler Model 3440 Roadreader nuclear moisture/density gauge offers two test modes for
Manual of Operation and Instruction - Troxler Labs
www.troxlerlabs.comManual of Operation and Instruction Model 3440 Surface Moisture-Density Gauge Troxler Electronic Laboratories, Inc. 3008 Cornwallis Rd. • P.O. Box 12057
Gauge Calibration at Troxler - Troxler Electronic …
www.troxlerlabs.comMore Information Surface moisture/density gauges that are calibrated by Troxler Electronic Laboratories (and laboratories that are approved for calibration by Troxler) are
UN3332, Radioactive Material, Type A Package, …
www.troxlerlabs.comUN3332, Radioactive Material, Type A Package, Special Form, 7, RQ Am-24 1, 1.48 GBq (40 mCi) UN2915, Radioactive Material, Type A Package, 7 …
Related documents
Emergent Literacy - Save the Children USA
www.savethechildren.orgreading skills in the early primary grades, without acknowledg ing ... children will gauge their future reading. iii In other words, if early experiences with books and reading are fun, exciting, ... II. What Research Tells Us about the Direct and Explicit Links between
TEST METHOD FOR EARTHWORK COMPACTION CONTROL …
www.dot.ny.govFor direct reading gauges; enter, on Form SM 418b lines H, J. K and L, the set of test data obtained at the highest Total Wet Density reading. 4.3.3 Use the spade to remove approximately 15 lbs. (7 kg) of material from the cross hatched area shown on Figure 2, Appendix B. Place the material in the tare; it will
DIRECT SHEAR TEST - Swedish College Of Engineering ...
scetcivil.weebly.comDirect Shear Test Results Load Deformation Readings Project : Sample No. : Type of Test : Proving reading Constant = 0.6lbs/div. Normal Load Applied = 18.34 kg (50 kN/m2) Vertical Dial Gauge Constant = 0.001” Horizontal Dial Gauge Constant = 0.01mm Moisture Content Determination Mass of Wet sample + Can (g) =
REAMER / IRRIGATOR / ASPIRATOR (RIA)
synthes.vo.llnwd.netThe distance of the depth gauge from the bone and the position of the receiver affect the diameter measurement. Always place the depth gauge on the side of the limb closest to the receiver. Estimate the real width as follows: Distance between depth gauge and bone • 25 mm = 1 mm larger reading • 50 mm = 2 mm larger reading
Calibrating Measuring Instruments Reference ... - Mitutoyo
www2.mitutoyo.co.jpGauge Blocks Automatic Gauge Block Interferometer GBI GBI Interference fringe analyzing processing Standard Configuration Standard Accessories Specifications Measurement target Rectangular gauge blocks Measuring range Up to 250mm Measuring uncertainty at the 95% confi dence level 0.025µm+0.2×10-6L L: Gauge block length (µm) Number of Gauge ...
DIAL BORE GAUGE INSTRUCTION MANUAL - 新潟精機株式 …
www.niigataseiki.net①Prepare a ring gauge to use as a reference standard for setting the zero-point. Insert the Measurement Head into the ring gauge. ②In cross section perpendicular to the axis of the ring gauge, position the gauge along diameter ⓐ(Figure: 1). This is the maximum distance, and at this point the Dial Indicator will read the minimum value.
11-0159A MTX-L PLUS - Innovate Motorsports
www.innovatemotorsports.comThe MTX-L PLUS gauge fits in any standard 2 1/16” (52mm) gauge pod. Mounting of the gauge should be done in such a manner that the cables are not being forcefully pulled and strained from the gauge itself. Route the sensor cable avoiding contact with the exhaust pipe and other hot sources that could melt the cable.
How the Railroad Won the War - American Experience
americanexperience.si.edugauge. This disconnect kept much of the South isolated. Freight would have to be offloaded to another mode of transport, usually a wagon train, and then re-loaded onto another locomotive. Standardizing the gauge throughout the system during the war was not an option for the South, which lacked the time, money, and supplies to do this successfully.