SWANCOR 901 - technipolymers.com

1 SWANCOR 901 Epoxy Vinyl Ester ResinsEntrgtf String t Cnrlronm*nltl ProttcilonProduct DescriptionSWANCOR 901 is a Bisphenol A type epoxy vinyl ester resin. Itprovides excellent corrosion resistance to a broad range oforganic and inorganic acids, alkalis, oxidizing chemicals and saltsolutions etc. It also provides very good mechanical strengthsuch as tensile and flexural while incorporated with reinforcementsuch glass fiber, carbon fiber or kevlar fiber etc. SWANCOR 901is designed to provide superior toughness with excellent fatigueresistance due to high heat distortion * Chemical storage tanks, pipes, flue gas desulfurizationsystems (FGD), scrubbers, ducts.

2 Corrosion resistant flooring while incorporated withaggregates.* Waste water treatment systems.* Food storage tanks and pure water system.* Marine use for yachts and boats, approved by DNV andLloyd's Methods* Can be easily applied by hand lay-up laminating, spray-up,pultrusion, resin transfer molding (RTM) and filamentwinding. Can be used in polymer concrete casting.* Can comply with US FDA regulation 21 CFR ifthe resin is properly formulated and properties of liquid resinProperty*1 ValueAppearanceClear amber liquidSolid Content (%)55 +/-1 Viscosity *2450+/-100cps450 +/- + Time (min)*15-25 Shelf Life (months)*1 Measurement was obtained under 25 C.

3 *2 LVT-#3-60rpm@25 C.*3 6%Cobalt: , 100% DMA: , Andonox LCR: @25 clear casting properties of cured resinTypical clear casting properties of cured resinPropertyTensile StrengthTensile ModulusTensile ElongationFlexural StrengthFlexural ModulusVolume ShrinkageHeat DistortionTemperature *5 Barcol HardnessSI*480~ ~ ~ ~ C30-38US Standard11,000~13, X ,000~22, F30-38 Test MethodASTM D638 ASTM D638 ASTM D638 ASTM D790 ASTM D790 ASTM D2566 ASTM D648 ASTM D2583*4 SI values based on conversion.*5 Cure condition for HDT: 24 hours at room temperature then2hoursat105 gel time of SWANCOR 901""""""---^^Gel TimeTemperature"---^Materials10-20 mi n20-40 min40-60 minCured by MEKP/CoOct/DMA*618 C/64 F250O77 F30 C/86 by BPO/DMA*718 C/64 F25 C/77 F30 C/86 *6 Concentration: Andonox LCR, CoOct: 6%, DMA: 100%*7 Concentration: BPO: 98%, DMA: 100%The data presented herein are believed to be accurate and reliable.

4 We require customers to inspect and test our product before use and to satisfythemselves as to contents and suitability for their specific applications. Information herein is to assist customers in determining whether our productsare suitable for their applications but not to be taken as a guarantee, express warranty or implied warranty of merchantability or fitness forparticular purpose, nor is any protection form any law or patent to be inferred. All patent rights are reserved. The exclusive remedy for all provenclaims is limited to replacement of our material and in no event shall we be liable for special, incidental or consequential : 1/2 Document Code:NT26-127-E Issue Date:AUG/2009 SWANCOR IND.

5 CO., 9 Industry South 6 Road, Nantou City 54066, TaiwanTel: +886 49 225 5420 Fax: +886 49 225 1534E-mail: nantou(5) 901 Epoxy Vinyl Ester ResinsNOTICE IN USE1. If SWANCOR 901 is blended with cobalt-salt promoters, shelflife will be shortened. Promoted SWANCOR 901 must beused within three The gel time of SWANCOR 901 is affected primarily bycatalyst concentration and temperature. The variations ofcure characteristics may be caused by the variations ofcatalyst, humidity, pigment, fillers and other additives. It isrecommended that the fabricators check the curecharacteristics with a small quantity resin before proceedingfor bulk SWANCOR 901 contains organic solvent (styrene).

6 Keepaway from heat, sparks and SWANCOR 901 is a potentially reactive chemical. Pleasestore it in dark and keep away from heat and direct Containers, not completely emptied must be closedimmediately after SAFETY AND HANDLING INFORMATIONRESIN STORAGEKeep away from ignition sources; flames, pilot lights, electricalsparks, and sparking tools. NO SMOKING. Do not store in directsunlight. Store separate from oxidizing materials, peroxides, andmetal salts. Keep container closed when not in use. To ensuremaximum stability and maintain optimum resin properties, resinsshould be stored in closed containers at temperatures below25 C(77 F).

7 Copper or copper containing alloys should beavoided as all ignition sources (flares, flames, including pilot lightselectrical sparks). Persons not wearing protective equipmentshould be exclude from area of spill until clean-up has beencompleted. Stop spill at source, dike area of spill to preventspreading, pump liquid to salvage tank. Remaining liquid may betaken up on sand, clay, earth, floor absorbent or other absorbentmaterial and shoveled into CONTACT:Thoroughly wash exposed area with soap and water contaminated clothing. Launder contaminated clothingbefore CONTACT:Flush with large amount of water immediately and continuouslyfor 20 minutes, lifting upper and lower lids occasionally.

8 Getmedical :Do not induce vomiting. Keep person warm, quiet and getmedical attention. Aspiration of material into the lungs can causechemical pneumonitis which can be :If affected, remove individual to fresh air. If breathing is difficult,administer oxygen. If breathing has stopped, give artificialrespiration. Keep person warm, quiet, and get medical PROTECTION:Do not breathe vapors. High concentration of vapor can behazardous. Keep out of sewers. Eliminate all sources of ignitionin vicinity of spill or released vapor to avoid fire or explosion. Forlarge spills, warn public of downwind explosion hazard.

9 Checkarea with explosion meter before re-entering area. Ground andbond all containers and handling DISPOSALD estroy by liquid incineration in accordance with applicableregulation. Contaminated absorbent should be disposed inaccordance to government packing is 200 kg steel data presented herein are believed to be accurate and reliable. We require customers to inspect and test our product before use and to satisfythemselves as to contents and suitability for their specific applications. Information herein is to assist customers in determining whether our productsare suitable for their applications but not to be taken as a guarantee, express warranty or implied warranty of merchantability or fitness forparticular purpose, nor is any protection form any law or patent to be inferred.

10 All patent rights are reserved. The exclusive remedy for all provenclaims is limited to replacement of our material and in no event shall we be liable for special, incidental or consequent ial : 2/2 Document Code: NT26-127-E Issue Date:AUG/2009 SWANCOR IND. CO., 9 Industry South 6 Road, Nantou City 54066, TaiwanTel: +886 49 225 5420 Fax: +886 49 225 1534E-mail: Promoted by Technipolymers, LLC 901-PT-VE-30 VINYLESTER LAMINATING RESIN technical data sheet Product Type: The 901-PT-VE-30 Vinylester laminating resin is a 100% vinylester resin in styrene. Basic Uses: The 901-PT-VE-30 is a high styrene content laminating resin used primarily in the production of fiberglass reinforced parts that require corrosion resistance or blister resistance from water.