Synology Router RT2600ac

1 Synology Router RT2600acHardware Installation GuideTable of ContentsChapter 1: Meet Your Synology RouterPackage Contents 3RT2600ac at a Glance 4 Safety Instructions 5 Chapter 2: Set up Your Synology RouterInstall Antennas 6 Position Your RT2600ac 7 Connect to Your RT2600ac 7 Set up Synology Router Manager (SRM) 9 Appendix A: SpecificationsAppendix B: LED Indicator Table 2 Synology_HIG_RouterRT2600ac_20181225 3 Chapter 1: Meet Your Synology RouterThank you for purchasing this Synology product! Before setting up your new RT2600ac , please check the package contents to verify that you have received all of the items below. Also, make sure to read the safety instructions carefully to avoid harming yourself or damaging your : All images below are for illustrative purposes only, and may differ from the actual ContentsMain unit x 1AC power adapter x 1RJ-45 LAN cable x 1 Antenna x 4 Meet Your Synology Router1 Chapter 3 4 Chapter 1: Meet Your Synology RouterRT2600ac at a NameLocationDescription1 Antenna BaseRear PanelInstall the included antennas Power ButtonPress to power on/off the Synology Power PortConnect the AC power adapter RESET ButtonPress and hold for four seconds (Soft Reset) or for ten seconds (Hard Reset).

2 5 USB PortConnect an external drive, USB printer, or other types of USB devices WAN PortConnect a network cable from the ISP modem into this port to establish WAN LAN PortConnect network cables into these ports to establish LAN SD Card SlotFront PanelInsert the SD card STATUS IndicatorDisplays the status of the Wi-Fi IndicatorDisplays the status of Wi-Fi 5G Wi-Fi IndicatorDisplays the status of 5G Wi-Fi WAN IndicatorDisplays the status of WAN LAN IndicatorDisplays the status of LAN USB PortLeft PanelConnect an external drive, USB printer, or other types of USB devices Eject Button1. Press to eject USB/SD external Displays the status of USB/SD external WPS ButtonRight PanelPress to start Wi-Fi ButtonPress to turn on/off the Wi-Fi : For LED indicator information, please refer to "Appendix B: LED Indicator Table". 5 Chapter 1: Meet Your Synology RouterSafety InstructionsKeep away from direct sunlight and away from chemicals.

3 Make sure the environment does not experience abrupt changes in temperature or humidity. Place the product right side up at all not place near any cleaning, unplug the power cord. Wipe with damp paper towels. Do not use chemical or aerosol prevent the unit from falling over, do not place on carts or any unstable power cord must plug in to the correct supply voltage. Make sure that the supplied AC voltage is correct and remove all electrical current from the device, ensure that all power cords are disconnected from the power of explosion if battery is replaced with an incorrect type. Dispose of used batteries appropriately. 6 Chapter 2: Set up Your Synology RouterInstall Antennas1 Point the antenna at the antenna base. 2 Turn clockwise until the antenna is Repeat Steps 1 and 2 to install the other antennas. For optimal Wi-Fi performance, tilt the antennas so that they are at a 90 degree angle to the up Your Synology Router2 Chapter 6 7 Chapter 2: Set up Your Synology RouterPosition Your RT2600acFor optimal performance, it is recommended to position your RT2600ac as advised below: On a stable surface ( an elevated shelf) away from any possible physical interruptions.

4 Close to the center of the area where the wired/wireless client devices are placed, and within a visible distance from the wireless devices. In a position where few walls and ceilings are between your RT2600ac and its client devices. Away from any potential electrical signal sources, such as other Wi-Fi routers , 3G/4G bases, and microwave ovens. Away from large expanses of metal or other materials, such as metal doors, glass panels, and concrete. Place Flat on a SurfaceSimply place your RT2600ac flat on a horizontal, stable to Your RT2600ac1 Use the included network cable to connect your RT2600ac (at the WAN1 port) to the ISP modem. Connect one end of the power adapter to the power port on your RT2600ac , and the other end to the power outlet. Press the power button to power on your RT2600ac . Wait for up to two minutes until the STATUS and WAN LED indicators turn :If you wish to use Smart WAN, connect your RT2600ac (at the WAN1 and LAN1 ports ) to the ISP modem with network cables.

5 The remaining LAN ports will be available for wired devices. 8 Chapter 2: Set up Your Synology Router2 Connect wireless client devices to your RT2600ac . When the LED indicators have turned static green, RT2600ac is ready to connect with other devices. Use your wireless device to scan and join the Wi-Fi network created by your :Below are the default credentials for the Wi-Fi network: Wi-Fi SSID: Synology_(Serial) Password: synologyThe default credentials can be changed during the initial SRM Connect wired client devices to your RT2600ac . Use network cables to connect devices to the LAN ports . The corresponding LAN LED indicators should turn orange/green to indicate successful connection. 9 Chapter 2: Set up Your Synology RouterSet up Synology Router Manager (SRM)1 Use a computer or wireless device connected to your RT2600ac 's local network. If you use a wireless device, scan and join the Wi-Fi network (SSID: Synology_(Serial); Password: Synology ).

6 2 Open a web browser, and enter either URL into the address bar: :80003 Once connected, click Start to launch the SRM Setup Fill in the information to set up the administrator account. Click Next to continue. 10 Chapter 2: Set up Your Synology Router5 Fill in the information to set up the Wi-Fi network. Click Next to Set up the operation mode. When choosing the Wireless Router mode, you can also enable External access to SRM so that only external access via the HTTP(S) port ( 8000/8001) can reach Choose an Internet connection type: PPPoE: Choose this option if you have obtained PPPoE credentials from the ISP. Manual IP: Choose this option if you have obtained an available IP address for use. Auto IP: Choose this option if you rely on an ISP modem for automatic IP assignment. 11 Chapter 2: Set up Your Synology Router8 The wizard will continue to set up your RT2600ac , and it may take up to three minutes to complete the After the setup is complete, click Start managing now to enjoy SRM and its various features.

7 Note: 1. Above is a general demonstration of the SRM setup steps. The steps and available options may somewhat vary depending on your device type ( PC or wireless device), access type (LAN, WAN, or Wireless LAN), and chosen operation mode (Wireless Router or Wireless AP).2. If the setup is to be completed with a wireless device, remember to download DS Router to manage your RT2600ac from anywhere. 12 Appendix A: Specifications ItemRT2600acExternal ports USB x 1 USB x 1 SD x 1 WAN PortGigabit WAN x 1 or Gigabit WAN x 2 (Dual WAN)LAN PortsGigabit LAN x 4 or Gigabit LAN x 3 (Dual WAN)Size (H x W x D) (mm)77 x 280 x 169 (without antennas)Weight (kg) kgSupported Clients (for SRM management) Windows 7 onwards Mac OS X onwardsFile SystemsExternal: EXT4, EXT3, FAT, NTFS, HFS+Wireless Standards : b/g/n 5 GHz: a/n/acOperating Frequency Range ( ): Up to 800 Mbps (5 GHz): Up to GbpsWireless Operation Modes Wireless Router Wireless AP (Access Point) Wireless Repeater (WDS)Wireless Security 64/128-bit WEP WPS support WPA2-Personal WPA/WPA2-Personal WPA2-Enterprise WPA/WPA2-Enterprise Opportunistic Wireless Encryption (OWE) WPA3-Personal WPA3-Enterprise WPA2/WPA3-PersonalAntennas4T4R Omni-directional high-gain dipole ( )Buttons & Switches Power WPS Wi-Fi On/Off Reset USB/SD EjectLanguage LocalizationEnvironment Requirements Line voltage: 100V to 240V AC Frequency: 50/60Hz Operating Temperature: 40 to 104 F (5 to 40 C) Storage Temperature: -5 to 140 F (-20 to 60 C) Relative Humidity: 5% to 95% RHNote: Model specifications are subject to change without notice.

8 Please refer to for the latest 13 Appendix B: LED Indicator Table Appendix B: LED Indicator TableLED IndicatorColorStatusDescriptionSTATUSG reenStaticPowered onOrangeStaticSystem booting / Rebooting / Hard ResetBlinkingRestoring settings (Soft Reset)Green / OrangeBlinkingFinding deviceOffPowered offWi-Fi( & 5G)GreenStaticWi-Fi onBlinkingWi-Fi activeOffNo Wi-FiWANG reenStaticNetwork connectedBlinkingNetwork activeOffNo networkLAN(1-4)GreenStaticGigabit connectionBlinkingNetwork activeOrangeStatic10/100 Mbps connectionBlinkingNetwork activeOffNo networkUSB/SD1 GreenStaticStorage detectedBlinkingTransmitting dataOrangeStaticReady for removalBlinkingEjecting storagesOffNo storageWPSG reenStaticWPS readyBlinkingWPS connection in progressOffWPS disabledNote: Model specifications are subject to change without notice. Please refer to for the latest Indicator TableBAppendix1 The USB/SD LED does not reflect the status of the 3G/4G dongle or printer attached to your Synology Router RT2600ac nit Lead (Pb) Mercury (Hg) Cadmium (Cd) Hexavalent chromium (Cr+6) Polybrominated biphenyls (PBB) Polybrominated diphenyl ethers (PBDE) O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O 1.

9 Wt % wt % 2. 3. Declaration of the Presence Condition of the Restricted Substances Marking Equipment name Type designation (Type) Restricted substances and its chemical symbols Note 1 Exceeding wt % and exceeding wt % indicate that the percentage content of the restricted substance exceeds the reference percentage value of presence condition. Note 2 indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence. Note 3 The indicates that the restricted substance corresponds to the exemption. Synology , USER LICENSE AGREEMENTIMPORTANT READ CAREFULLY: THIS END USER LICENSE AGREEMENT ("EULA") IS A LEGAL AGREEMENTBETWEEN YOU (EITHER AN INDIVIDUAL OR A LEGAL ENTITY) AND Synology , INC. (" Synology ") FOR THESYNOLOGY SOFTWARE INSTALLED ONTO THE Synology PRODUCT PUCHASED BY YOU (THE "PRODUCT"),OR LEGALLY DOWNLOADED FROM , OR ANY OTHER CHANNEL PROVIDED BYSYNOLOGY ( "SOFTWARE").

10 YOU AGREE TO BE BOUND BY THE TERMS OF THIS EULA BY USING THE PRODUCTS CONTAINING THESOFTWARE, INSTALLING THE SOFTWARE ONTO THE PRODUCTS OR DEVICE CONNECTED TO THE PRODUCTS. IF YOU DO NOT AGREE TO THE TERMS OF THIS EULA, DO NOT USETHE PRODUCTS CONTAINING THESOFTWAREOR DOWNLOAD THE SOFTWARE FROM , OR ANY OTHER CHANNELPROVIDED BY , YOU MAY RETURN THE PRODUCT TO THE RESELLER WHERE YOUPURCHASED IT FOR A REFUND IN ACCORDANCE WITH THE RESELLER'S APPLICABLE RETURN 1. Limited Software License. Subject to the terms and conditions of this EULA, Synology grants you a limited, non-exclusive, non-transferable, personal license to install, run and use one copy of the Software loaded on the Product or onyour device connected to the Product solely relating to your authorized use of the 2. Documentation. You may make and use a reasonable number of copies of any documentation provided with theSoftware; provided that such copies will only be used for internal business purposes and are not to be republished orredistributed (either in hard copy or electronic form) to any third 3.