Table of Contents

Hole Sizes for Cut Tapping - STANLEY® Engineered Fastening

- 1 - stanleyengineeredfastening.com Chips Hole Sizes for Cut Tapping These charts are supplied as a recommendation only. Actual sizes may vary depending on application and the material being tapped.

  Size, Tapping, Hole, Hole sizes for cut tapping

POP Blind Riveting Systems

POP ® The POP ® rivet installation sequence is simple. 1. Place the mandrel of the POP ® rivet into the nosepiece of the setting tool. 2. Insert the POP ® rivet body through the hole of the materials to be fastened. 3. Pull the trigger of the setting tool. The POP ® Rivet body clamps the materials together and expands to form a secondary head on the blind side of the joint.

www.StanleyEngineeredFastening.com www ...

Insert, Screw Thread, Self Locking (Inch Series) NASM33537 Insert, Standard Dimensions, Assembly (Inch Series) NASM8846 Insert, Screw Thread, Helical Coil (Inch Series) MA1565 Insert, Screw Thread, Helical Coil (Metric Series) MA1567 Insert, Screw Thread, Helical Coil, Standard Dimensions, Assembly (Metric Series) MA3279, 3280, 3281

  Thread, Dimensions

Inserts - STANLEY® Engineered Fastening

Insert, corrosion resistant Helical Coil Coarse Thread (Inch Series) NASM124651 thru NASM124850 Insert, corrosion resistant Helical Coil Fine Thread (Inch Series) NASM21209 Insert, Screw Thread, Self Locking (Inch Series) NASM33537 Insert, Standard Dimensions, Assembly (Inch Series) NASM8846 Insert, Screw Thread, Helical Coil (Inch Series) MA1565

  Standards, Thread, Inch, Insert

Stud, Ferrule & Accessory Catalog

Many studs, pins, anchors, and ferrules are featured to provide the greatest range of possible solutions to your stud welding applications. Bookmarks have been added to make navigation through the catalog quick and easy. Text explanations have been added to clarify some of the potential uses of each stud.

  Catalog, Solutions, Ferrules, Dust, Accessory, Ferrule amp accessory catalog

2020 Stud, Ferrule & Accessory Catalog

2020 Nelson® Stud Welding . Stud, Ferrule & Accessory Catalog . This catalog is designed to be a user-friendly source of information about the Nelson Stud Welding line of studs, anchors, pins, and the standard accessories used to weld them. Many features have been

  Welding, Dust, Nelson, Stud welding, Nelson stud welding

Torx Plus Drive System - STANLEY® Engineered Fastening

TORX PLUS Drive is a drive system designed to ensure optimum torque transmission and, ultimately, required clamp load. With a true 0° drive angle, the TORX PLUS system virtually eliminates the radial forces that can cause stress on fastener recesses. The elliptically-based geometric configuration of the TORX PLUS Drive System maximizes

  System, Transmissions

DFMA = Design for Assembly + Manufacturing

tapping including: – Minimize the threaded length in the hole. 1.5x the major diameter often provides sufficient strength. – Avoid blind holes where possible. If you must thread a blind hole, allow room at the bottom of the hole for 1/2 major diameter more than the threads. – Don’t over-specify the thread percentage.

  Tapping, Hole

THREAD CUTTING & FORMING

Chipless Tapping-A fluteless tap is used for Ø < ½” => cold formed in holes in ductile metals only-The required forming torque is twice the cutting torque that is necessary to cut the section.-They produce better accuracy than the fluted ones-The diameter of the hole must be well controlled-Lubricants (water soluble soaps ) are essential

  Tapping, Hole

Machining Guide for Engineering Plastics

applied, especially when hole depths are more than twice the diameter. In order to improve heat and swarf removal, frequent pull-outs (peck drilling) are necessary, especially for deep holes (pull-out the drill every time a depth ≈1.5 x the diameter is attained). For large diameter holes, it is advisable to use drills with a

  Engineering, Plastics, Hole, For engineering plastics

Chapter 5 Installing Balusters - Bayer Built

baluster firmly into the hole. 2. Next, place a small drop of glue on the top of the baluster and slide the angle cut of the baluster into the plowed portion of the rail. 2. On the previously marked intersecting lines of the baluster, drill a hole about 1-inch deep with a brad point bit of the appropriate diameter.

  Hole

Installation Guide

A class 3 self-tapping wing-tipped screw for fastening to 0.5mm to 1.6mm BMT light gauge steel frames. 1000 per box. Part No. 305984 COMPONENTS NOT SUPPLIED BY JAMES HARDIE James Hardie recommends the following products for use in conjunction with its Scyon™ Linea™ weatherboard and Scyon™ Axent™ trim.

  Guide, Installation, Installation guide, Tapping