Transcription of Taylor indoor outdoor thermometer instructions 1730
1 ContinueTaylor indoor outdoor thermometer instructions 1730by 1528 WeatherGuide System with MOON Remote Sensor Command Manual 1 FASAW elcome to Weather System. Simple, reliable, accurate .. it allows you to monitor the location of the interior or exterior from one room. The base unit reads the internal conditions, while wirelessly remote sensors report external weather conditions back to the baseunit for an all-in-one weather display. Plan your workday, play the day, every day. Now it's smart! Weather Power Content Table .. 3 How To Set Up WeatherGuide.
2 For power of your WeatherGuide Base Unit Your Weather Base Unit the base unit can be powered by either an AC adapter (including) or 2 AAA batteries (excluding). Adaptratepower - insert the end of the adaptier connector into the jack on the side of the base unit. Tip the rest into the right electrical tract. Battery Power Remove the battery compartment cover on the back of the unit. Install 2 AAA batteries. Replace the battery compartment cover. If the shipment is successful, remote delivery of successful sensor readings andicons will appear on the base unit.
3 If the dashes are still displayed on the recipients unit, press the Tx button again. To convert the temperature display of the remote sensor to Celsius, press the +C/F button in the remote battery compartment. Select F or C to replace the remote battery compartment cover. The remote control will automatically sendreadings to the base unit. How to Display your WeatherGuide Over schedule - use the Table Stand behind the foundation and the remote sensor unit of the Wall - use the keyhole behind the basic and remote sensor units. Keyhole Base Unit Table Stand Remote Sensor Base unit location - Place the unit inside the house in a good location ventilated awayfrom direct sunlight.
4 Remote sensor location - The remote sensor delivery range is 100 feet. Atomic Clock and Your Weather Calendar have a radio-controlled clock/calendar that sets itself up to a radio signal sent by the Atomic Clock located in synchronizing the atomic clock: 1. Press and hold the button -PMCE/RCC behind the baseunit. Press and hold -PMCE/RCC to synchronize atomic clocks. Release when the bear unit. Steady icon = Synchronized atomic clock (may take up to 24 hours to capture signals). Press PMCE/RCC to select the time zone. unit will beep.
5 How to Set press Clock Manually and hold SET/AL to start clock settings Press +C/F or -PMCE/RCC to reset theseconds. Press SET/AL to enter the moment. Press +C/F or -PMCE/RCC to change the minutes. Press SET/AL to insert minutes. Repeat to set other clock/calendar settings. To set the clock manually: 1. Press and hold the SET/AL. Unit button will beep. 2. Press +C/F or -PMCE/RCC to set the moment Press SET/AL to enter. 3. Press +C/F or -PMCE/RCC tochange the clock. Press SET/AL after selecting 12/24 hours. Tip: Hold down the +C/F or -PMCE/RCC button to quickly forward the digits.
6 The clock set Daylight Saving Time - to turn on the DST, press mode until OFF appears in the clock digits. Press and hold the SET/AL button until it switches to ON. DST is now above. Press MOD to return to the watchview. Press Mode, then press and hold SET/AL, then press Mode to change the DST. How To Set Your Weather Alarm has 2 separate alarm settings. Press and hold SET/AL Hour digit flash Press +C/F or -PMCE/RCC to change business hours. Press SET/AL to enter the business hours. Minutes of the flash digits. Repeat to set the minute. Alarm 1 activeAlarm 2 active 2.
7 Press and hold the SET/AL button. The unit will beep and the alarm clock digits will flash. 3. Press +C/F or -PMCE/RCC to change the clock. Press SET/AL to enter. The minutes will blink. 4. Press +C/F or -PMCE/RCC to change the minutes. Press SET/AL to enter. Press Mode then SET/AL to turn off alarm To turn off the alarm: PressMODE until the Alarm display appears. Press the SET/AL button. The alarm icon will be lost. The alarm is off. No alarm icon = alarm is turned off. Press Snooze/Light to disarm the Snooze Press the Snooze/Light button at the top of the base unit to dissipate the alarm for 5 minutes.
8 The icon will flash as long as the tow is active. The tow will deactivate whenthe alarm is turned off. How to read your WeatherGuide Basic Unit displays internal conditions from its location. A secluded unit will send weather readings from its location back to the base unit. Alternatively, a remote sensor investigation cord can be used. Plug the investigative cord into the rubber plug on a remote sensor. Leave the end to hang whereyou want to measure the temperature (outside the windows, aquariums, swimming pools, etc. The auto scroll will switch between different remote sensor readings Auto Scroll features - the base unit can be set to scroll automatically through reading.)
9 To activate the Auto Scroll, press the Channel button behind the base unit until an automatic scroll symbolappears on the LCD. The base unit will automatically display the basic and remote readings for 10 seconds each. Temperature Reading Temperature/Humidity displays a temperature display in the middle left side of the See Minimum/Maximum temperature/humidity readings During Weather AndaGuide will keep the last recorded high and lowtemperatures recorded and humidity within 24 hours. A 24-hour period begins when the battery is installed.
10 Press MIN/MAX to see high and low daily temperature & humidity 1. Press the Min/Max button once to see the highest Today. Minimum or Max 2 readings. Press the Min/Max button again to see the lowest temperature/humidity of the Pressure Reading Pressure Barometric refers to the pressure given by the atmosphere at the given altitude. It can be expressed in klibars (mb)/hectopascals (hPa), or inches of merqueries (inHg). Rising or falling barometric pressure readings indicate the possibility of fair or bad weather conditions. - High or increased barometric pressureindicates fair weather conditions.
