Technical Data - Newmans Valve

1 TC9308-2 newco Pressure Seal valves Technical Data2TC9308-2 All the information contained in this manual is the exclusive property of Cameron. Any repro-duction or use of the calculations, drawings, photographs, procedures or instructions, either expressed or implied, is forbidden without the written permission of Cameron or its autho-rized Release 01 October 2013 Produced by Technical Publications, Houston, TX, USA 2013 Cameron3TC9308-2 PREFACEThe procedures included in this book are to be performed in conjunction with the requirements and recommendations outlined in API Specifications. Any repairs to the equipment covered by this book should be done by an authorized Cameron service representative.

2 Cameron will not be responsible for loss or expense resulting from any failure of equipment or any damage to any property or death or injury to any person resulting in whole or in part from repairs performed by anyone other than authorized Cameron personnel. Such unauthorized repairs shall also serve to terminate any contractual or other warranty, if any, on the equipment and may also result in equipment no longer meeting applicable copies of this manual are maintained. Revisions and/or additions will be made as deemed necessary by Cameron. The drawings in this book are not drawn to scale, but the dimensions shown are book covers Cameron Box 1212 Houston, Texas 77251-1212 713-939-2211 :5TC9308-2 TABLE OF CONTENTSO verview.

3 7 Materials ..8I. Body/Bonnet Materials ..8 II. Trim Materials ..9 III. Sour Gas Service Materials ..10 IV. Features and Benefits ..10 Pressure Temperature Ratings - ASME ..11 Dimensions ..15I. Flange ASME ..15 II. Butt Weld ASME ..18 Auxiliary Connection Locations ..19 Gate Valve Features ..21I. Cast Steel Pressure Seal Bonnet ..21 Gate Valve Materials ..22I. Cast Steel Pressure Seal Bonnet ..22 Gate valves ..23I. Cast Steel Pressure Seal Bonnet Class 600 and 900 ..23 II. Cast Steel Pressure Bonnet Class 1500 and 2500 ..24 Globe and Angle Valve Features ..25I. Cast Steel Pressure Seal Bonnet ..25 Globe and Angle Valve Materials.

4 26I. Cast Steel Pressure Seal Bonnet ..26 Globe and Angle valves ..27I. Cast Steel Pressure Seal Bonnet Class 600 and 900 ..27 II. Cast Steel Pressure Seal Bonnet Class 1500 and 2500 ..28 Lift Check Valve Features ..29I. Cast Steel Pressure Seal Bonnet ..29 Lift Check valves ..31I. Cast Steel Pressure Seal Bonnet Class 600 to 2500 ..31 Valve Weights ..32I. Pressure Seal II. Pressure Seal III. Pressure Seal Lift Check ..346TC9308-2 Testing ..35 Ordering Chart ..36 Ordering All Cameron newco Products ..37 Industry Standards Typically Used in Valve Manufacturing ..387TC9308-2 OVERVIEWV alve and TagThe identification tag displays all construction and tracking data regarding the respective Valve on which it is attached.

5 Below is a general overview of the identification tag tags are located in 1 of the 3 following areas: Yoke Body/Bonnet Flange Under the Handwheel NutTrim Description750 PSI @ 100 FC5/CR13, CR13, HFNPS 2S/N 100419 FIG. 13F-C5 CLASS 300 API 600/ISO10434 Serial NumberNominal Port SizeDesign SpecificationPressure ClassModel Pressure Temperature Rating NEWCO6300 WCB77T5158 BrandSizePressure ClassBody MaterialPatternHeat Tag LocationsHeat BODY/BONNET MATERIALSC ameron s newco cast steel valves are available in stock in a wide range of body/bonnet materials and optional trim materials. Listed below are some of the more popular materials.

6 Additional materials are available. Please contact Cameron or your local distributor for DesignationCommon DescriptionASTM Material Service Limitations*CBCarbon SteelA216 Non-corrosive service water, oil and gases at temperatures between -20 F and +800 Temp CarbonA352 Low temperature service between -50 F and +650 Chrome and 1% MolyA217 Non-corrosive service water, oil and gases at temperatures between -20 F and +1100 Chrome and 1% MolyA217 Non-corrosive service water, oil and gases at temperatures between -20 F and +1100 Chrome and .5% MolyA217 Corrosive, non-corrosive or erosive service at temperatures between -20 F and +1200 Chrome and 1% MolyA217 Corrosive, non-corrosive or erosive service at temperatures between -20 F and +1200 Chrome, 1% Moly, and VA217 Corrosive, non-corrosive or erosive service at temperatures between -20 F and +1200 316A351 Corrosive, cryogenic or high temperature servicebetween -450 F and +1200 20A351 Corrosive service at temperatures between -20 F and +300 F.

7 * Limitations are per 2004 Edition of ASME TRIM MATERIALSThe following are Cameron s newco standard trim Trim NumberCommon NameAPI 600 Ring Facing (1)Wedge or Disc Facing (1)StemOther Trim Parts (2)Service Limitations113 Chrome1CR 13CR 13CR 13CR 13 Non-corrosive , gas and general service to 700 and oil vapor to 900 Stellite8 HFCR 13CR 13CR 13 Steam, gas and general service to 1000 trim for gate Stellite5 HFHFCR 13CR 13 Premium trim service to 1200 F. Excellent for high pressure water and steam services to 850 F. Low temperature service standard for 316 SS Stellite12HF3163163164/3316/Full Stellite16 HFHF3163165 Monel9 NiCuNiCuNiCuNiCuCorrosive services to 750 Stellite11 HFNiCuNiCuNiCu5/3 Monel/Full Stellite-HFHFNiCuNiCu6 Alloy 2013A20A20A20A20 Corrosive services to 300 , gas or low pressure steam to 450 Bronze-AL BRZAL BRZAL BRZAL BRZ8 Iron-IronIronSTLIron or STLXS pecialSpecialSpecialSpecialSpecialSpecia lCustomer to specify.

8 (1) Facing is defined as the seating surface of a seat ring and wedge/disc.(2) Other trim parts are defined as small internal parts that are normally in contact with the service fluid. This includes the stem, backseat bushing in gate and globe valves and the swing check disc SOUR GAS SERVICE MATERIALSC ameron s newco cast steel valves may be furnished with body and trim materials in compli-ance with NACE MR-01-75 specifications. The standard Valve is WCB with double tempered trim 2 and Class II bolting. Other materials, trim and bolting are available. To order the con-figuration you require, please specify the appropriate figure number and suffix designation as shown on Page FEATURES AND BENEFITS Certifications International Organization for Standardization (ISO) Traceability Fugitive Emmisions Tested API-598 Tested Major End-user Approved Multiple Global Locations Extensive Engineering Capabilities Excellent Customer Service Warranty Onsite Non-destructive Testing Field Services for Start-up Inhouse Automation Capabilities11TC9308-2 PRESSURE TEMPERATURE RATINGS ASME 150 Temperature F ( C)

9 WCB*LCCWC6WC9C5C12C12A-20 to 100 (-29 to 38)285290290290290290290200 (93)260260260260260260260300 (148)230230230230230230230400 (204)200200200200200200200500 (260)170170170170170170170600 (316)140140140140140140140650 (343)125125125125125125125700 (371)110-110110110110110750 (399)95-9595959595800 (427)80-8080808080850 (454)65-6565656565900 (482)50-5050505050950 (510)35-35353535351000 (538)20-20202020201050 (566)--20**20**20**20**201100 (593)--20**20**20**20**201150 (621)----20**20**201200 (649)----20**20**20 Class 300 Temperature F ( C)WCB*LCCWC6WC9C5C12C12A-20 to 100 (-29 to 38)740750750750750750750200 (93)680750750750750750750300 (148)655730720730730730730400 (204)635705695705705705705500 (260)605665665665665665665600 (316)570605605605605605605650 (343)550590590590590590590700 (371)530-570570570570570750 (399)505-530530530530530800 (427)410-510500510510510850 (454)320-485485485485485900 (482)230-45045037545045012TC9308-2 Class 300 Temperature F ( C)WCB*LCCWC6WC9C5C12C12A950 (510)135-3203852753753851000 (538)85-2152652002553651050 (566)--1451751451703601100 (593)--951101001153001150 (621)--657060752251200 (649)--40403550145 Class 600 Temperature F ( C)WCB*LCCWC6WC9C5C12C12A-20 to 100 (-29 to 38)

10 1480150015001500150015001500200 (93)1360150015001500150015001500300 (148)1310145514451455145514551455400 (204)1265140513851410141014101410500 (260)1205133013301330133013301330600 (316)1135121012101210121012101210650 (343)1100117511751175117511751175700 (371)1060-11351135113511351135750 (399)1015-10651065106510651065800 (427)825-10151015101510151015850 (454)640-975975975975975900 (482)460-900900745900900950 (510)275-6407555507557751000 (538)170-4305354005057251050 (566)--2903502903457201100 (593)--1902202002256051150 (621)--1301351251504451200 (649)--808070 10529013TC9308-2 Class 900 Temperature F ( C)WCB*LCCWC6WC9C5C12C12A-20 to 100 (-29 to 38)2220225022502250225022502250200 (93)2035225022502250225022502250300 (148)1965218521652185218521852185400 (204)1900211020802115211521152115500 (260)1810199519951995199519951995600 (316)1705181518151815181518151815650 (343)1650176517651765176517651765700 (371)1590-17051705170517051705750 (399)1520-15951595159515951595800 (427)1235-15251525152515251525850 (454)955-14601460146014601460900 (482)690-13501350112013501350950 (510)410-9551160825113011601000 (538)255-65080559576010901050 (566)--43052543051510801100 (593)--2903303003409051150 (621)--1952051852256701200 (649)