Technical Data Sheet - Jotun

1 ^(ValidationDate)31403140;3240;43201,2po lyurethaneTechnical Data SheetHardtop XPProduct descriptionThis is a two component chemically curing aliphatic acrylic polyurethane coating. It has a glossy finish with very good gloss retention. It is a high solids product . The product has good application properties with low dry be used as topcoat in atmospheric and certificatesThis product contributes to the Green Buildings Standard credits. Please see section Green Building System 1, , Newcastle Occupational HealthFood, Compliant with USA, FDA Title 21, Part for dry solidsWhen used as part of an approved scheme, this material has the following certification:- Low Flame Spread in accordance with EU Directive for Marine Equipment.

2 Approved in accordance with parts 5 and 2 of Annex 1 of IMO 2010 FTP Code, or Parts 5 and 2 of Annex 1 of IMO FTPC when in compliance with IMO 2010 FTP Code Ch. 8 Consult your Jotun representative for to colour card and Multicolor Industry tinting system (MCI)Typical useOther variants availableHardtop XP AluHardtop XPLH ardtop XPF (Winter grade version)Marine:Recommended for topside, deck and :Recommended for offshore environments, refineries, power plants, bridges and buildings. Suitable for a wide range of industrial structures. Used as a topcoat in pre-qualified NORSOK to separate TDS for each certificates and approvals may be available on dataPropertyTest/StandardDescriptionSoli ds by volumeGloss level (GU 60 )ISO 2813 VOC-US/Hong KongUS EPA method 24 (tested)(CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)63 Flash pointISO 3679 Method 130 Cgloss (70-85)323 3233 2 %Date of issue:22 March 2021 Page: 1/6 This Technical Data Sheet supersedes those previously Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the Application Guide (AG) for this product .

3 For your nearest local Jotun office, please visit our website at Data SheetHardtop XPVOC-EUIED (2010/75/EU) (theoretical)The provided data is typical for factory produced products, subject to slight variation depending on g/lGloss description: According to Jotun Performance Coatings' data is valid for mixed VOC values refer to white 23985-2009 (tested)330 g/lVOC-KoreaKorea Clean Air Conservation Act (tested)(Max. thinning ratio included)385 g/lFilm thickness per coatDry film thicknessWet film thicknessTheoretical spreading rateTypical recommended specification colours may need film thickness in the high end of the recommended specification range to achieve effect colours may have diverging specification range.

4 Refer to the Application Guide (AG) for additional information or contact your nearest Jotun office. m mm /l---Surface preparation summary tableSubstrateMinimumRecommendedClean, dry and undamaged compatible coatingCoated surfacesClean, dry and undamaged compatible coatingSurface preparationApplication methodsThe product can be applied bySpray:Use air spray or airless :Recommended for stripe coating and small areas. Care must be taken to achieve the specified dry film :May be used. Care must be taken to achieve the specified dry film preparationTo secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any of issue:22 March 2021 Page: 2/6 This Technical Data Sheet supersedes those previously Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the Application Guide (AG) for this product .

5 For your nearest local Jotun office, please visit our website at Data SheetHardtop XPProduct mixing ratio (by volume)Hardtop XP Comp A10part(s)part(s)1 Hardtop XP Comp BThinner/Cleaning solventThinner: Jotun Thinner No. 10 Jotun Thinner No. 26 is supplied and used in USA due to is not normally required. Consult the local representative for advice during application in extreme conditions. Do not thin more than allowed by local environmental Thinner No. 26/Nozzle tip (inch/1000):Pressure at nozzle (minimum):Guiding data for airless spray13-19150 bar/2100 psiNozzle tip:Pressure at nozzle (minimum):Guiding data for air sprayHVLP: 11-19 (inch/1000) / Pressure pot: (mm)HVLP: bar/30 psi / Pressure pot: bar/30 psiDrying and Curing timeSurface (touch) dryWalk-on-dry16 h6 h2 h24 h14 h7 h4 h21 d14 d7 d3 dSubstrate temperature5 C10 C23 C40 CDried/cured for serviceDry to over coat, minimum24 h14 h7 h4 hWalk-on-dry.

6 Minimum time before the coating can tolerate normal foot traffic without permanent marks,imprints or other physical and curing times are determined under controlled temperatures and relative humidity below 85 %, and at average of the DFT range for the to over coat, minimum: The recommended shortest time before the next coat can be (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal for service: Minimum time before the coating can be permanently exposed to the intended maximum overcoating intervals, refer to the Application Guide (AG) for this of issue:22 March 2021 Page: 3/6 This Technical Data Sheet supersedes those previously Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the Application Guide (AG) for this product .

7 For your nearest local Jotun office, please visit our website at Data SheetHardtop XPInduction time and Pot lifePot h50 minPaint temperature23 C40 CTemperatureDry, atmosphericHeat resistance C120 ContinuousPeak140 CPeak temperature duration max. 1 temperatures listed relate to retention of protective properties. Aesthetic properties may suffer at these compatibilityPrevious coat:epoxy, zinc epoxy, epoxy mastic, polyurethanePackaging (typical)The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary due to local of containers(litres)Hardtop XP Comp / XP Comp / / 201 / 3 Storage The product must be stored in accordance with national regulations.

8 Keep the containers in a dry, cool, well ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle with life at 23 C4848 Hardtop XP Comp AHardtop XP Comp Bmonth(s)month(s)In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf life , thereafter the paint quality is subject to (litres)Depending on the actual exposure of the coating system, various primers and topcoats can be used in combination with this product . Some examples are shown below. Contact Jotun for specific system of issue:22 March 2021 Page: 4/6 This Technical Data Sheet supersedes those previously Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the Application Guide (AG) for this product .

9 For your nearest local Jotun office, please visit our website at Data SheetHardtop XPGreen Building StandardsThis product contributes to Green Building Standard credits by meeting the following specific requirements:LEED v4 (2013)MR credit: Building product disclosure and optimization- Material Ingredients, Option 2: Material Ingredient Optimization, International Alternative Compliance Path -REACH optimization: Fully inventoried chemical ingredients to 100 ppm and not containing substances on the REACH Authorization list Annex XIV, the Restriction list Annex XVII and the SVHC candidate Environmental product Declarations.

10 product -specific Type III EPD (ISO 14025;21930, EN 15804).BREEAM International (2016)- Mat 01: product -specific Type III EPD (ISO 14025;21930, EN 15804).BREEAM International (2013)- Hea 02: VOC content for Two-pack performance Coatings SB (500 g/l) (EU Directive 2004/42/CE).The EPDs are available at product is for professional use only. The applicators and operators shall be trained, experienced and have the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun 's Technical documentation. Applicators and operators shall use appropriate personal protection equipment when using this product .