Technical Data Sheet - Jotun

1 ^(ValidationDate)574574;5761,2epoxyTechn ical Data SheetMarathonProduct descriptionThis is a two component polyamine cured epoxy coating . It is a high solids, high build, glass flake reinforced product. It is scratch and abrasion resistant. Suitable for environments with very high corrosivity. Can be used as primer, mid coat, finish coat or as single coat system in atmospheric and immersed environments. Suitable for properly prepared carbon steel and concrete and certificatesAPAS approved to specification 0213 NORSOK Standard M-501, Edition 6, coating system no.

2 7A - Carbon and stainless steel in the splash zone NORSOK Standard M-501, Edition 6, coating system no. 7B - Submerged carbon and stainless steel 50 CNORSOK Standard M-501, Edition 6, coating system no. 7C - Submerged carbon and stainless steel >50 CColoursselected range of coloursTypical useMarine:Specially suited in areas where high scratch resistance is :Suitable for structural steel and piping to be exposed to corrosive environments up to very high and for offshore environments, refineries, power plants, bridges, buildings, mining equipment and general structural steel.

3 Compatible with cathodic protection certificates and approvals may be available on dataPropertyTest/StandardDescriptionSoli ds by volumeGloss level (GU 60 )ISO 2813 VOC-US/Hong KongUS EPA method 24 (tested)(CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)VOC-EUIED (2010/75/EU) (theoretical)The provided data is typical for factory produced products, subject to slight variation depending on pointISO 3679 Method 130 Cgloss (70-85)210 g/l248 description: According to Jotun Performance Coatings' data is valid for mixed 3233 VOC-ChinaGB/T 23985-2009 (tested)134 g/lVOC-KoreaKorea Clean Air Conservation Act (tested)(Max.)

4 Thinning ratio included)219 g/l 2 %Date of issue:19 April 2021 Page: 1/5 This Technical Data Sheet supersedes those previously Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at Data SheetMarathonFilm thickness per coatDry film thicknessWet film thicknessTheoretical spreading rateTypical recommended specification range20025044005002 m mm /l---Surface preparation summary tableSubstrateMinimumRecommendedSa 2 (ISO 8501-1)Carbon steelSa 2 (ISO 8501-1)Coated surfacesClean, dry and undamaged compatible coatingClean, dry and undamaged compatible coatingConcreteMinimum 4 weeks curing.

5 Moisture content maximum 5 %. Prepare the surface by means of enclosed blast shot or diamond grinding and other appropriate means to abrade the surrounding concrete and to remove 4 weeks curing. Moisture content maximum 5 %. Prepare the surface by means of enclosed blast shot or diamond grinding and other appropriate means to abrade the surrounding concrete and to remove primed steelSa 2 (ISO 8501-1)Sa 2 (ISO 8501-1)Surface preparationApplication methodsThe product can be applied bySpray:Use airless :Recommended for stripe coating and small areas. Care must be taken to achieve the specified dry film preparationTo secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any of issue:19 April 2021 Page: 2/5 This Technical Data Sheet supersedes those previously Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the Application Guide (AG) for this product.

6 For your nearest local Jotun office, please visit our website at Data SheetMarathonProduct mixing ratio (by volume)Marathon Comp A3part(s)part(s)1 Marathon Comp BThinner/Cleaning solventThinner: Jotun Thinner No. 17 Nozzle tip (inch/1000):Pressure at nozzle (minimum):Guiding data for airless spray21-31150 bar/2100 psiDrying and Curing timeSurface (touch) dryWalk-on-dry14 h3 h32 h12 h6 h14 d7 d3 dSubstrate temperature10 C23 C40 CDried/cured for serviceDry to over coat, minimum32 h12 h6 hWalk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks,imprints or other physical and curing times are determined under controlled temperatures and relative humidity below 85 %, and at average of the DFT range for the to over coat, minimum: The recommended shortest time before the next coat can be (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal for service.

7 Minimum time before the coating can be permanently exposed to the intended maximum overcoating intervals, refer to the Application Guide (AG) for this time and Pot lifePot life1 hPaint temperature23 CDate of issue:19 April 2021 Page: 3/5 This Technical Data Sheet supersedes those previously Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at Data SheetMarathonNote that the coating will be resistant to various immersion temperatures depending on the specific chemical and whether immersion is constant or intermittent.

8 Heat resistance is influenced by the total coating system. If used as part of a system, ensure all coatings in the system have similar heat , sea waterDry, atmosphericHeat resistance C120 ContinuousPeak120 C70 C80 CPeak temperature duration max. 1 temperatures listed relate to retention of protective properties. Aesthetic properties may suffer at these compatibilityPrevious coat:Subsequent coat:epoxy, zinc epoxy, inorganic zinc silicatepolyurethane, polysiloxane, epoxy, vinyl epoxyPackaging (typical)The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary due to local of containers(litres)Marathon Comp B5 Marathon Comp A15205 Storage The product must be stored in accordance with national regulations.

9 Keep the containers in a dry, cool, well ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle with life at 23 C4848 Marathon Comp AMarathon Comp Bmonth(s)month(s)In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf life, thereafter the paint quality is subject to (litres)Depending on the actual exposure of the coating system, various primers and topcoats can be used in combination with this product. Some examples are shown below. Contact Jotun for specific system of issue:19 April 2021 Page: 4/5 This Technical Data Sheet supersedes those previously Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the Application Guide (AG) for this product.

10 For your nearest local Jotun office, please visit our website at Data SheetMarathonCautionThis product is for professional use only. The applicators and operators shall be trained, experienced and have the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun 's Technical documentation. Applicators and operators shall use appropriate personal protection equipment when using this product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing the and safetyPlease observe the precautionary notices displayed on the container.