Technical Specification - cogeneration.com.ua

1 GE Jenbacher GmbH & Co OHGA-6200 Jenbach, AustriaJMS 612 gas +43 5244 600-0 Fax +43 5244 63255 Jenbacher gas enginesTechnical SpecificationJMS 612 gas Module data:Additional information:Electrical outputkW pressure level (engine, average value 1m)dB(A)100 Recoverable thermal output (120 C) pressure level exhaust gas (1m, 30 off engindB(A)116 Energy gas mass flow rate, Consumption based on a LHV ofExhaust gas volume, wetNm ,5 kWh/Nm Nm exhaust back pressure after enginembar60 Electrical efficiency%42,6%Exhaust gas temperature at full load C [8]397 Thermal efficiency%43,2%Combustion air mass flow efficiency%85,8%Combustion air volumeNm to be dissipated (LT-Circuit)kW95 Max.)

2 Inlet cooling water temp. (intercooler) C40 Emission values:Max. pressure drop in front of intake-air filtermbar10 NOx < 250 mg/Nm (5% O2) Return temperature C70 Forward temperature C90 Hot water flow ratem /h79,1 Engine data:Alternator:Engine typeJ 612 GS-E02 ManufacturerLeroy-SomerConfigurationV 60 TypeLSA 53 VS65No. of cylinders12 Type displacementlit74,85 Efficiency at = 1,0%97,3%Nominal at = 0,8%96,2%Mean piston speedm/s11 Ratings at = 1, effe. press. at stand. power and nom. spebar20,00 Ratings at = 0, ratioEpsilon11,0 FrequencyHz50 ISO standard fuel stop power ICFN kW1871 VoltageV690 Spec.

3 Fuel consumption of enginekWh/kWh2,28 Protection ClassIP 23 Specific lube oil consumptiong/kWh0,30 Insulation classHWeight capacity lube on methane number|Min. methane numbMZ94|80 Technical parameters:Applicable standards:Based on DIN-ISO 3046 Based on VDE 0530 REM with specified toleranceStandard conditions:Air pressure:1000 mbar or 100 m above sea levelAir temperature:25 C or 298 KRelative Humidity:30%Engine output derating:Gas quality:according to TA 1000-0300 Gas flow pressure:80 - 200 mbar(Lower gas pressures upon inquiry)Prechamber gas pressure: 3,3-4,0 barMax.

4 Variation in gas pressure: 10%All data are based on engine full load at specified media temperatures and are subject to Technical Instruction TA 1100-0110 "PARAMETER FOR GE Jenbacher GAS ENGINES" must be strictly plants installed at > 500m above see level and/or intake temperature > 30 C, the reduction of engine power is determined for each gas enginesTechnical SpecificationBasic engine equipment:Module equipment:*Exhaust gas turbocharger, Intercooler*Base frame for gas engine,*Motorized carburator for LEANOX control alternator and heat exchangers*Electronic contactless high performance ignition system*Internal pole alternator with excitation alternator and*Lubricating oil pump (gear driven) with automatic voltage regulator; 0,8 lagging to 1,0*Lubricating oil filters in main circuit*Flexible coupling, bell housing*Lubricating oil sump.

5 Lubricating oil heat exchanger*Anti-vibration mounts*Jacket water pump*Air filter*Fuel-, lubricating oil and jacket water pipe work on engine*Automatic lube oil replenishing with level control*Flywheel for alternator operation; Exhaust gas manifold*Wiring of components to module interface panel*Viscous damper*Crankcase breather*Knock sensors*Jacket water electric preheatingEngine accessories:*Electric starter motor*Electronic speed governor*Electronic speed monitoring device including starting and Module control panel: overspeed control*Totally enclosed , single door cubicle, wired to terminals and *Transducers and switches for oil pressure, jacket water temp.

6 , ready to operate, protection IP 41 outside, jacket water pressure, charge pressure and mixture temperature IP 10 inside, according to VDE-standards*One thermocouple per cylinderControl equipment:*Engine-Management-System (Dialog Network)Supplied loose: **Visualisation (industry PC-10'' color graphics display): Operation data,Gas train according to DIN-DVGW consisting of: controller display,Exh. gas temp.,Generator electr. connection,etc.*Manual stop valve, fuel gas filter, two solenoid valves, **Central engine- and module control: Speed-, Power output-, Leakage control device, gas pressure regulator LEANOX-Control and knock control, Gas Train*Multi-transducerDocumentation:*Loc kable operation mode selector switch*Operating and maintenance manual Positions: "OFF", "MANUAL", "AUTOMATIC"*Spare parts manual*Demand switch*DrawingsAssembly, painting, testing in Jenbach/AustriaIdentical to Genset except that heat recovery is included.

7 *jacket water heat exchanger mounted on module frame*exhaust gas heat exchanger mounted as separate heat recovery module*all heat exchangers with complete pipework*Heat exchangers and all inherent auxiliariesScope of Supply & Design Subject to Local Regulations and product development>>> Scope of supply genset - JGS 612 >>> Scope of supply module - JMS 612 gas enginesTechnical SpecificationGensetMain dimensions and weights (approximate value)Connections (at genset)Length water inlet and outletDN/PN100/10 Width gas outletDN/PN500/10 Height gas (at gas train)DN/PN100/16 Weight water connection:Weight Temperature CircuitDN/PN65/10 ModuleMain dimensions and weights (approximate value)Connections (at module)Length water inlet and outletDN/PN100/10 Width gas outletDN/PN500/10 Height gas (at gas train)DN/PN100/16 Weight water connection.

8 Weight water-Inlet/Outlet 2nd stageDN/PN65/10 Heat recovery moduleMain dimensions and weights (approximate value)Connections (on heat recovery module)Width water inlet and outletDN/PN100/10 Height gas outletDN/PN500/10 Length drainDN/PN50/10 Drain line '' ''GE Jenbacher GmbH & Co OHGTel. +43 5244 600-0A-6200 Jenbach, AustriaFax +43 5244 6325504. Jul gas enginesTechnical Specificatio