Example: confidence
TRIM MATERIAL - kinkavalves.com
2H (d) 304 (Hardfaced) Stellite 6 Stellite 6 Type 304 Stainless Steel X, Y, Z (f) Type 304 Stainless Steel Stellite 6 5 Hardfaced Co Cr-A Stellite 6 Stellite 6 13% Chromium X, Y, Z (f) 13Cr 13% Chromium Co Cr-A Stellite 6 13Cr 13% Chromium Ni-Cr Ni-Cr 9 Monel Ni-Cu Alloy Monel Monel Monel X, Y, Z (e) (f)
Tags:
Information
Domain:
Source:
Link to this page:
Related documents
Type 3241-1 and Type 3241-7 Pneumatic Control Valves Type ...
www.samsongroup.comUndivided valve bonnet up to NPS 6 Valve plug • Metal seal • Soft seal • High-performance metal seal Optional with RFID tags with one-to-one device marking ... for ≤NPS 4 plug up to seat bore 38 made of solid Stellite available. 3) Other packings on request (u T 8000-1) 4) Other materials on request. T 8012 EN 5
Alloy Valves from stock
alloy-valves.comFull stellite trims, combination of CS A216 WCB body and alloy trim HF Acid (CS/Monel or Monel/Monel) Check valves Duo Check 2” – 72”, 150#, 300#, 600#, 800# 900#, 1500#, 2500# in BW and RF Monel, Alloy 20, F347, duplex, super duplex, inconel, hastelloy C276 / B3, titanium
切削条件表 - fuji-bc.com
www.fuji-bc.comStellite-6 Ti 5Al- .5Sn Ti 6- -4- 焼 鈍 320-350 S&A 370-415 焼 鈍 300-350 S&A 350-395 焼 鈍 170-235 ブリネル 硬度 S 220-280 S 220-280 S & A 370-390 S 165-205 S & A 270-315 S & A 300-345 応力除去 280 冷間圧延 240-315 鋳 造 220-280 360-405 焼 鈍 110-175 焼 鈍 280-330 焼 鈍 300-350 送り mm/rev 切削速度 m/min 0.1 0 ...
Visible Dye Penetrant Testing - Magnaflux
www.magnaflux.comiron, steel, stainless steel, carbides, stellite, certain plastics and ceramics. The essentials of the method are: penetration of the defect by the dye penetrant - removal of the excess penetrant from the surface - development of the indication - inspection. A deep red indication will mark the defect.
STELLITE 21 ALLOY - Deloro
www.deloro.comStellite TM 8. CORROSION RESISTANCE Stellite TM 21 is resistant to oxidizing and reducing gaseous atmospheres up to 1150°C (2100°F). Because its ternary alloying element is Mo and not W, it has higher resistance to reducing or complex environments (e.g. sulphuric acid, hydrochloric acid, and sour gas) than CoCrW alloys such as Stellite TM 6 ...
MSC094 Final ver5d - MSC Industrial Direct
cdn.mscdirect.comNon Ferrous 1700 0.0003 0.0006 0.0010 0.0013 Stainless Steel 525 0.0003 0.0006 0.0010 0.0013 High Temp Alloys 100 0.0003 0.0006 0.0010 0.0013 Steel 600 0.0003 0.0006 0.0010 0.0013 Cast Iron 600 0.0003 0.0006 0.0010 0.0013 Important Disclaimer: The Accupro speed and feed rates are suggested by the manufacturer as a general guideline.Machine type, horsepower,