UltraClave Automatic Sterilizers - Henry Schein

1 FOR USE BY MIDMARK TRAINED TECHNICIANS ONLYS ervice andParts ManualSF-1854 Part No. 004-0453-00 Rev. E (4/25/12)UltraClaveAutomatic SterilizersModel Numbers:M9M9DM11M11D-020 thru -022-020 & -022-020 thru -022-020 & -022 Serial Number Prefixes:RN, RP, RR, VRW, RX, VRS, RT, RV, VRY, RZ, V FOR USE BY MIDMARK TRAINED TECHNICIANS ONLYT able Of ContentsGENERAL INFORMATIONS ymbols .. iOrdering Parts .. iModel / Serial NumberLocation .. iWeights, Dimensions,Electrical Specifications .. iiModel Identification /Compliance Chart .. iiiCycle Parameters .. ivSpecial Tools.

2 IvWarranty Information .. vOPERATION &TROUBLESHOOTINGE rror Codes .. A-2 Power-Up Mode .. A-18 Fill Mode .. A-20 Heat-Up Mode .. A-22 Sterilization Mode .. A-24 Vent Mode .. A-26 Door Motor System .. A-28 Drying Mode .. A-30 Fan System .. A-32 TESTING & REPAIRC hecking forPressure Leaks .. B-2 Using a Pressure Gauge .. B-3 Fuses .. B-4 Service Diagnostics .. B-5 Air Valve .. B-12 Fill & Vent Valves .. B-15 Pressure Relief Valve .. B-18 Heating Element .. B-20 Temperature Sensor .. B-23 Water Level Sensor .. B-27 High-Limit Thermostats .. B-31 Door Switch .. B-34 Touch Pad & Display Panel.

3 B-37 TESTING & REPAIR - continuedDoor Motor System .. B-39 Fan & Fan Thermostat .. B-42 Main PC Board .. B-46 Printer (optional) ..B-50 Adjusting the Dry Time .. B-54 ACCESS PROCEDURESR emoving & Installing:Covers / Panels .. C-2 Tray Plate / Rack .. C-3 Draining / Filling Reservoir .. C-4 WIRING & FLOW DIAGRAMSM9 (-020 / -021 / -022):Wiring Diagram ..D-2 Flow (-020 / -022):Wiring (-020 / -021 / -022):Wiring Diagram ..D-2 Flow (-020 / -022):Wiring VIEWS / PARTS LISTSM9 (-020 / -021 / -022) ..E-2M9D (-020 / -022): .. E-3M11 (-020 / -021 / -022) ..E-2M11D (-020 / -022).

4 E-3 General InformationSection ESection ESection BSection BSection CSection DSection Ai Midmark Corporation 2004 SF-1854 General InformationSymbolsCautionIndicates a potentially hazardous situationwhich could result in injury if not AlertIndicates a potentially hazardous situationwhich could result in equipment damage if not a procedure, practice, or that the component the check mark appearsbeside should be tested before replacing Section A, test the components in the order indicated.(ex. 1st then, 2nd )Refer to Section B for component testing symbols are used throughout this manual to represent theoperational status of functions and the function / component is working action the function / component is working,but a problem the function / component is not working at / Serial Number LocationGeneral Information 333333333333333 Ordering PartsThe following information is required when ordering parts: Serial number & model number Part number for desired part.

5 [Refer to Section E: Exploded Views / Parts Lists]Non-warranty parts orders may be faxed to Midmark usingthe Fax Order Form in the back of this warranty parts orders, call Midmark's Technical ServiceDepartment with the required :8:00 am until 5:00 pm EST [Monday - Friday]Phone:1-(800)-MidmarkMA616300iSer ial NumberModel / Serial NumberiiGeneral Information Midmark Corporation 2004 SF-1854MA599600iBACDW eights, Dimensions, Electrical SpecificationsDimensions [Refer to illustration]: Front Height (A) .. in. ( cm) Width (B) .. in. ( cm) Depth w/plug (C).

6 In. (51 cm) Back Height (D) .. in. ( cm)Standard Tray Dimensions M9 / M9D (Large).. 7 5/16 in. x 12 in. x 7/8 in. ( cm x cm x cm) M9 / M9D (Small).. 5 5/8 in. x 12 in. x 7/8 in. ( cm x cm x cm)Chamber Size:..Diameter: 9 in. ( cm) Depth: 15 in. ( cm)Shipping Carton: (Length x Width x Height).. in. x in. x 21 in. ( cm x 52 cm x cm)Weight: Shipping 81 lbs ( kg) w/reservoir 73 lbs ( kg) w/reservoir 82 lbs (37 kg)Reservoir Capacity.

7 Approx. gallon ( liters) at FULL markPressure Relief Valve:opens at approximately:..40 psi (275kPa)Electrical Requirements:..[See Model Identification /..Compliance Chart]Fuses (on main PC board):115 VAC model F1 .. amp, 250 V, Slo-Blo, 1/4" x 1-1/4" F2 ..15 amp, 250 V, Fast-Acting, 1/4" x 1-1/4"230 VAC models: F1 .. amp, 250 V, Slo-Blo, 5mm x 20mm F2 ..8 amp, 250 V, Fast-Acting, 5mm x 20mmPower Consumption: 115 VAC watts, 12 amps @ 120 VAC 230 VAC watts, 7 amps @ 240 VACHeat Emission: M9 / M9D.

8 5000 BTU/Hr during operationM9 / M9D Model InformationDimensions [Refer to illustration]:Front Height (A) .. in. ( cm)Width (B) .. in. ( cm)Depth w/plug (C) .. in. ( cm)Back Height (D) .. in. ( cm)Standard Tray DimensionsM11 / M11D (Large).. 9 in. x 15 in. x 1 1/8 in. ( cm x 38 cm x cm)M11 / M11D (Small).. 6 5/8 in. x 15 in. x 1 1/8 in. ( cm x 38 cm x cm)Chamber Size:..Diameter: 11 in. ( cm) Depth: 18 in.

9 ( cm)Shipping Carton:(Length x Width x Height).. in. x in. x 21 in. (66 cm x cm x cm)Weight:Shipping lbs ( kg)w/reservoir 99 lbs ( kg)w/reservoir lbs ( kg)Reservoir Capacity:..Approx. gallon ( liters) at FULL markPressure Relief Valve:opens at approximately:..40 psi (275kPa)Electrical Requirements:..[See Model Identification / Compliance Chart]Fuses (on main PC board):115 VAC modelsF1.

10 Amp, 250 V, Slo-Blo, 1/4" x 1-1/4"F2 ..15 amp, 250 V, Fast-Acting, 1/4" x 1-1/4"230 VAC models:F1 .. amp, 250 V, Slo-Blo, 5mm x 20mmF2 ..8 amp, 250 V, Fast-Acting, 5mm x 20mmPower Consumption:115 VAC watts, 12 amps @ 120 VAC230 VAC watts, 7 amps @ 240 VACHeat Emission:M11 / BTU/Hr during operationATTENTIONA seperate (dedicated) electrical circuit is recommended for all models (M9/D &M11/D). Do not connect to a circuit with other devices, unless the circuit is ratedfor the additional 8/10M11 / M11D Model Informationiii Midmark Corporation 2004 SF-1854 General InformationModel Identification / Compliance Chart - M9/D & M11/DUL61010A-1 LABORATORYEQUIPMENT59 FMledoMnoitpircseDlaireSrebmuNsexiferP:o TseilpmoC.