Example: dental hygienist
Using the ColdFire Flash Module with the MCF521x ColdFire
4.1 CFM Clock Divider Register The following code lines are used to configure the CFMCLKD, Figure 2, to assign the CFM frequency. /* Select FLASH frequency to 200 kHz. Section 15.4.3.1 MCF5213RM */ MCF_CFM_CFMCLKD = MCF_CFM_CFMCLKD_DIV(25) | MCF_CFM_CFMCLKD_PRDIV8;. IPSBAR Offset: 0x1D_0002 (CFMCLKD) Access: User …
Information
Domain:
Source:
Link to this page:
Documents from same domain
All Digital VCXO Replacement Using a Gigabit Transceiver
www.eeweb.comQPLL output with run-time configurable parameters (e.g., gain, cutoff frequency, and clock divider values) to enable you to set up the operation specifically for the end application. This allows the flexibility of the reference input signal and DPLL cleaning bandwidth. Application Note: UltraScale FPGAs and UltraScale+ Devices
MMCM and PLL Dynamic Reconfiguration - EEWeb
www.eeweb.comEvery clock output has a divider group associated with it. The divider group is composed of the following parameters: † High Time e m i T w o †L † No Count †Edge The first two parameters associated with the divider group are the High and Low Time counters. These counters set the number of voltage-controlled oscillator (VCO) clock cycles ...
Horizontal Synchronization Locking System for Video ... - EEWeb
www.eeweb.comThe NCO function is performed by using the Sigma Delta output to drive the V divider clock enable. The Sigma Delta output is a pulse stream whose duty cycle is directly controlled by the VOLT output on the DPLL. That is, when the VOLT output is 0: • The Sigma Delta output is 0 •The V dividers are never enabled
AN 635: Implementing SATA and SAS Protocols in Altera …
www.eeweb.com(3) The high-speed serial clock runs at 750 MHz (1.5 Gbps), 1500 MH z (3 Gbps), and 3000 MHz (6 Gbps), depending on the SATA and SAS da ta rates. Parallel Recovered Clock RX Phase Compensation FIFO (2) (2) (2) (2) TX Phase Compensation FIFO Byte Ordering Byte Deserializer Byte Serializer 8-, 16-, or 32-bit Interface (1) 8B/10B Decoder 8B/10B ...
Related documents
All Digital VCXO Replacement Using a Gigabit Transceiver
www.eeweb.comQPLL output with run-time configurable parameters (e.g., gain, cutoff frequency, and clock divider values) to enable you to set up the operation specifically for the end application. This allows the flexibility of the reference input signal and DPLL cleaning bandwidth. Application Note: UltraScale FPGAs and UltraScale+ Devices
MMCM and PLL Dynamic Reconfiguration - EEWeb
www.eeweb.comEvery clock output has a divider group associated with it. The divider group is composed of the following parameters: † High Time e m i T w o †L † No Count †Edge The first two parameters associated with the divider group are the High and Low Time counters. These counters set the number of voltage-controlled oscillator (VCO) clock cycles ...
Horizontal Synchronization Locking System for Video ... - EEWeb
www.eeweb.comThe NCO function is performed by using the Sigma Delta output to drive the V divider clock enable. The Sigma Delta output is a pulse stream whose duty cycle is directly controlled by the VOLT output on the DPLL. That is, when the VOLT output is 0: • The Sigma Delta output is 0 •The V dividers are never enabled
AN 635: Implementing SATA and SAS Protocols in Altera …
www.eeweb.com(3) The high-speed serial clock runs at 750 MHz (1.5 Gbps), 1500 MH z (3 Gbps), and 3000 MHz (6 Gbps), depending on the SATA and SAS da ta rates. Parallel Recovered Clock RX Phase Compensation FIFO (2) (2) (2) (2) TX Phase Compensation FIFO Byte Ordering Byte Deserializer Byte Serializer 8-, 16-, or 32-bit Interface (1) 8B/10B Decoder 8B/10B ...