WARNING - blueox.com

1 BX21902007-10 Ford Edge Installation Instructions292-2942 Rev G Page 1 of 8 4/14/16 Please visit for the latest version of these installation your vehicle owner s manual for manufacturer s towing specifications. Serial NumberIf the front of your vehicle looks different than this, please contact us at (402)385-3051.!Failure to read and follow these instructions could result in separation of the towed vehicle from the tow bar, causing property damage, loss of towed vehicle, personal injury or SizeGrade 5 Grade 81/4 10145/16 19293/8 33477/16 54781/2 781195/8 1542303/4 257380 Bolt Torque Specifications Torque in Foot-Pounds for Inch Bolts Bolt Torque Specifications Torque in Foot-Pounds for Metric Bolts Bolt SizeGrade Tab Height: 26-1/2 Attachment Tab Width.

2 26 Please read BOTH these Installation Instructions and the General Information sheet prior to installing or operating this Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who are familiar with our products and have the equipment and knowledge necessary to do fit work . If needed, Blue Ox Dealers can be found at or by contacting our Technical Service Department at (402) Many Blue Ox baseplates are designed to use existing holes and hardware to mount the baseplate to the towed vehicle. Even though bolts are there, do not assume they are adequate for baseplate mounting.

3 Always use the hardware supplied in the hardware kit and existing hardware as specified in the installation instructions. BX21902007-10 Ford EdgeInstallation Instructions292-2942 Rev G Page 2 of 8 4/14/16213 CONNECTOR1134-PINCONNECTOR41412797785151 610716-PIN6 Tools RequiredLoctite RED 3/4 Socket Phillips Screwdriver 9/16 SocketHammer 8MM SocketReciprocating Saw 13MM Socket1 1/4 Hole Saw 10MM SocketUtility Knife SocketRef. No. Qty. Part # Description1 2 61-4029 Weldment, 1/2 Nut Wire2 1 61-6386 Weldment, Baseplate, BX21903 2 62-3469 Attachment, Assembly, SF/LB, 1 Hole4 2 201-0060 1/2-13x1 Hex Bolt, Grd.

4 5, ZP5 2 201-0192 #10-32x1/2 Slot, Round Head Screw6 4 201-0443 3/8-16x1 Hex Bolt, Grd. 5, ZP7 n/a Existing Bolts8 2 201-0979 #12-14 x 1 Self Drilling Screw, ZP9 2 202-0047 #10-32 Hex Nut10 4 202-0071 3/8-16 Hex Flange Whiz Lock Nut, ZP11 4 203-0003 3/8 Flat Washer.

5 ZP12 2 203-0005 1/2 Flat Washer, ZP13 4 203-0010 3/8 Lock Washer, ZP14 2 203-0012 1/2 Lock Washer, ZP15 2 203-0054 #10 Lock Washer16 1 299-0685 4-Way Bracket 2 290-0437 Cap Plug, Black (Not Shown)

6 2 229-0359 Quicklink, 3/8 , ZP (Not Shown) 2 226-0046 Baseplate Safety Cable, 36 Class III (Not Shown)Important:Use only genuine factory replacement parts on your baseplate. Do NOT substitute homemade or non-typical parts. If a bolt is lost or in need of replacement, for your safety and the preservation of your baseplate, be sure to use a replacement bolt of the same grade (In most cases it will be Grade 5, please reference the parts list above). Replacement parts may be ordered through your nearest Blue Ox Dealer or Distributor.

7 Failing to follow and/or altering these installation instructions in either installation or required equipment will void the manufacturer s warranty. Towing behind a non-motorized vehicle will void the Ford EdgeInstallation Instructions292-2942 Rev G Page 3 of 8 4/14/161. Using a Phillips screwdriver, remove two plastic Phillips push pins (see white arrows) and then using a 10MM socket, remove one bolt (see grey arrow) from the flat plastic piece on top. Do this to both sides of the vehicle. Set bolts and push pins aside to be reinstalled later. 1 2. Using a socket, remove three bolts just forward of the front tire on the wheel well.

8 Do this to both sides of the vehicle. Set bolts aside to be reinstalled later. 2 Instruction Notes: The fascia, headlights and windshield washer fluid reservoir are removed and reinstalled for the baseplate installation. Some drilling and trimming is all components that are removed on a flat, sturdy surface. All items will be reinstalled unless otherwise noted after the baseplate is installed. The dimensional variations between otherwise identical vehicles can be considerable. While the baseplate was designed for easy installation, it may be necessary to tailor the baseplate slightly to compensate for vehicle manufacturer s tolerances.

9 The BX8848 4-Diode Wiring Kit is recommended for this Handling of some cosmetic parts when installing this product may require the use of protective covers, rags, specialty tools, etc. to prevent damage. When using power drills be aware of the dangers of torque and drill bit length. When using a reciprocating saw be aware of objects behind the cutting surface. Use a good quality paint to spray cut edges of frame to prevent rusting. Be sure that ALL electrical connections are plugged in and accessories are functioning properly before reinstalling the fascia. The baseplate is computer tested to your vehicle s GVWR, exceeding this weight will void the manufacturer s warranty.

10 Be sure to use a sufficient amount of Loctite Red on all bolt threads before tightening. Tighten all bolts according to the torque chart provided. Dealer or installer be certain the user receives these instruction sheets. If the baseplate is in an accident, it must be replaced. DO NOT use it again! An accident can cause unseen damage and using it again could result in more damage or serious injury. DO NOT use the baseplate if it is damaged or missing parts. BX21902007-10 Ford EdgeInstallation Instructions292-2942 Rev G Page 4 of 8 4/14/163. Using a socket, remove two bolts that are located underneath.