WARNING - READ YOUR OWNERS MANUAL - Supplies

1 WARNING - read your OWNERS MANUALM anual before any steps are taken to operate or maintain this machineGENERAL MAINTENANCENEVERNEVERDO NOTUSE ONLYDAILYadd chemicals or pretreat parts - doing so may cause foaming, fire hazard and personal the water disposal/recycle feature until all floating oil is skimmed/ removed. To do so maycreate a fire hazard resulting in personal injury and/or property skim all oil from your washer unless you are preparing to perform the water recycle function. A%" layer of oil on top of the solution is beneficial because it reduces steaming and retards specifically made for use in recirculating, cabinet style automatic parts washers. Any othermaterial may cause foaming, fire hazard and personal injury.

2 Maintain your washer's water level. Water level should be just below the oil skimmer exit pipe. Do not allowwater level to get too low. Check after every 8 hours of operation. Water temperature should be no less than 140 F and no more than 195 F. Use a thermometer to determineactual temperature. Wash at as low a temperature as Oil Removal System (overnight) if the oil layer in your washer is over 2" deep.(NOTE: If your unit has Auto-Water-Fill - disconnect the AWF plug before using the Oil Removal Feature.)1. Place a catch pan (at least 3 gallons) under the oil removal pipe (left side of washer).2. Open ball Flip oil removal switch to "on" position. All other switches should be in the "off" Allow system to run Close ball valve after Oil Removal is DaysOperate Water Recycle/Disposal feature.

3 NOTE: See OWNERS MANUAL before first use.(NOTE: If your unit has Auto-Water-Fill - disconnect the AWF plug before using the Water Recycle Feature.)1. Do not operate the Water Recycle/Disposal feature until all floating oil is skimmed/removed, washer is cooledand all oil has come to the Remove baskets, turntable and Delta-Wave filter from the Ventilate washer cabinet (remove cap from vent pipe, connect 4" clothes dryer vent hose to vent pipe OPENFRONT DOOR OF WASHER AT LEAST 1")4. Turn on the "HEAT TIME" Control until water heater light turns off (to preheat water).5. Water Recycle/Disposal switch is "on". All other controls are "off1. Momentarily depress "START" Remove solid waste from floor of washer and dispose of properly (see OWNERS MANUAL ).

4 7. Clean out spray Clean rod on Low-Water Float (located inside unit on front-left panel near oil skimmer wheel). Debris can buildup on the rod and cause the float to stick.'NVIROUIPOWNER'S MANUALWARNINGRead your owner 's ManualMaintain your washer's water level properlyNEVER add chemicals or pretreat parts - doing so may cause foaming,fire hazard and personal perform the water disposal/recycle feature until all floating oil isskimmed/removed. To do so may create a fire hazard resultingin personal injury and/or property totally skim all oil from your washer unless you are preparing toperform the water recycle function. A %" layer of oil on top of thesolution is beneficial because it reduces evaporation and ONLY detergent specifically made for use in recirculating, cabinet styleautomatic parts washers.

5 Any other material may causefoaming, fire hazard and personal washer will operate reliably for years with minimal careand maintenance. Thank and Start UpLocation ConsiderationsYour EnviroQuip automatic parts washer is designed to replace old style sink on a drum typesolvent washers. It may be used to wash any and all parts that you used to wash in washer needs to be located for the convenience of your technicians so they can washparts without leaving their work washer should be level side-to-side and slightly higher in the front. Allow 1ft. of clearanceon all sides of the unit. Do not install and operate the washer on or near flammable washer must be on concrete.

6 Do not use on a wood pallet. your washer containsswitches and contactors that may spark when turning on and off. The washer's skintemperature can operate as high as 200 degrees when using the water RequirmentsIn normal daily wash operations, your washer does not need to be vented. You will find that acap is installed on the vent pipe of your washer. When in normal operation, this vent cap helpsretain heat in the washer and minimize water loss due to evaporation and is removed onlywhen operating the water recycle/disposal water recycle/disposal feature operates by bringing all of the water in the washer to a hardboil and converting the water into steam.

7 This steam must be allowed to escape the cabinet todispose of the water within the forced evaporation of this quantity of water will generate a lot of steam, which willcondense back into distilled water. For this reason, you may wish to consider the followingoptions when selecting a site for your automatic parts washer: Vent your washer with a vent hose out through a wall to allow this steam outdoors. A 4"clothes dryer vent hose works fine. (See service section for detailed venting instructions.)Vent Pipe If your shop is large and fairly well ventilated, you may also place the vent hose into a 55-gallon drum and allow the steam to condense into the drum.

8 The condensed steam isclear, distilled water that can be used to refill your washer after clean : 07/02 Page 1 Installation and Start Up You may also wish to place the end of the vent hose near a floor drain to allow thecondensed, distilled water to flow into it. To limit the amount of steam leaving the hose,use a minimum 10ft hose. The longer the ventilation hose, the more the steam escapingthe cabinet will condense back into distilled water before leaving the vent hose. Vent the steam out directly from the washer in a large, well-ventilated shop. Open the flip-top and the front door of the washer. LEAVE THE CAP ON THE NOTREMOVE IT.

9 This option will decrease the recycle time, as the steam dissipates at a morerapid to Electrical PowerConsult the specification sheet in the rear of this MANUAL for proper breaker size. Do not use awild leg (measures more than 120 VAC above ground) to power single phase ) MAKE SURE THAT ALL SWITCHES AND ELECTRICAL CONTROLS ARE "OFF"BEFORE CONNECTING TO ELECTRICAL ) your washer is equipped with a low water protection circuit. Upon connection to electricalpower you should see a lighted indicator on the front control panel that is titled "LowWater." This function is operated by a float switch and prevents the pump and immersionheater from operating if the washer does not have a high enough water level to protectthese Start UpYour washer is designed to clean with soap and water.

10 NEVER INTRODUCE SOLVENTS ORMATERIALS WITH FLASH POINTS BELOW 220 FAHRENHEIT, OR ANY OTHER TOXICMATERIALS INTO your ENVIROQUIP WASHER. TO DO SO MAY RESULT IN FIREEXPLOSION, INJURY OR ) your washer comes with a starter kit that contains a pre-measured charge of EQ-3 GeneralPurpose Soap. Add this soap to the washer before filling with water. Open the oildischarge valve. "Hose in" the powdered detergent to dissolve it into wash solution andcontinue to add water until it begins to exit the discharge pipe. Be sure to close the oildischarge valve after filling with ) Check the belt drive for the turntable by lifting the hinged cover on the top of the washer tomake sure that the belt has adequate tension to turn the turntable, but is not so tight thatthe belt cannot slip if the turntable is jammed.