Flange dimension guide - Reece

Drilling for ANSI B16.5, Class 150 is compatible with ANSI B16.1, Class 125 Flange dimensions Nominal size: 40mm. Flange dimensions Flange dimension guide 9 ISO 7005 (DIN) PN6 140 110 4 14 M12 16 - 11 16 PN10 165 125 4 18 M16 20 19 11 20 PN16 165 125 4 18 M16 20 19 11 -

Pressure - Temperature Ratings (psig) Class - 150#

Vize LLC | 13964 S. Wayside Houston, TX 77048 USA | Toll Free: 877.411.VIZE | info@vizellc.com | www.vizellc.com

  Pressure, Class, Temperatures, Ratings, Pressure temperature ratings, Psig

Rosemount 3051 Pressure Transmitter - Emerson Electric

Traditional flange, 316 SST, alloy C-276 drain/vent ★ HJ DIN-compliant traditional flange, SST, 7/16-in. (10 mm) adapter/manifold bolting ★ FA Level flange, SST, 2-in. (51 mm), ANSI Class 150, vertical mount 316 SST drain/vent ★ FB Level flange, SST, 2-in. (51 mm), ANSI Class 300, vertical mount 316 SST drain/vent ★

  Class, Flange, Class 150

AWWA Butterfly Valves 3 – 20 - Henry Pratt Company

Pressure Class: n Class 150B per AWWA Standard C504 Working Pressure: 150 psig Flanges: n Flat faced and drilled in accordance with ANSI B16.1, Class 125 standards. Rubber Seat: Bonded seat-in-body Actuation Options: n ®Pratt hand lever n MDT manual actuator with AWWA nut, handwheel or chainwheel n Pratt Dura-Cyl hydraulic or pneumatic cylinder

  Class

Weld Neck Flanges - ANSI B16

Class 150 lb Pipe Flange Data Hub Data Raised Face Drilling Data Weight Nominal Pipe Size Outside Diameter Overall Diameter Inside Diameter Flange Thickness min Overall Length Diameter at Weld Bevel Hub Diameter Face Diameter Number of Holes Bolt Hole Diameter Diameter of Circle of Holes kg/ in piece mm in mm in mm in mm in mm in mm in mm in mm ...

  Class, Ansi, Flange, Neck, Weld, Class 150, Weld neck flanges ansi

CONTROL VALVE HANDBOOK - Emerson Electric

Emerson Automation Solutions Flow Controls Marshalltown, Iowa 50158 USA Sorocaba, 18087 Brazil Cernay, 68700 France Dubai, United Arab Emirates Singapore 128461 Singapore

  Handbook, Control, Valves, Control valve handbook

ANSI Chart Cast and Ductile Iron Flange Chart Dimensions ...

ANSI 125 150 250 300 CLASS CAST IRON & DUCTILE IRON FLANGE (ASME B16.1 & B16.42) CHART DIMENSIONS & PRESSURE TEMPERATURE RATINGS In terms of drilling and fl ange O.D. 125 class is the same as 150 class and 250 class if the same as 300 class. It should be noted that some soft seated valves such as knife gate, rubber lined butterfl y or sluice

  Chart, Pressure, Class, Temperatures, Dimensions, Ratings, Flange, Chart dimensions amp pressure temperature ratings, 150 class

Temperature Measurement Devices - Swagelok

–100 to 150 –70 to 70 01 –40 to 160 –40 to 70 19 0 to 200 –15 to 90 05 0 to 250 –20 to 120 06 50 to 300 10 to 150 08 50 to 550 10 to 290 16 150 to 750 65 to 400 11 200 to 1000 100 to 540 12 Dial range not available with silicone liquid fill. Not recommended for continuous use over 800°F (426°C). 1/4 in. hex adjustment 1.46

  Devices, Measurement, Temperatures, Swagelok, Temperature measurement devices

STEEL FLANGE DIMENSIONS t;:;F~ m t+--G;:]

The regular '!winch raised face of Class 150 and 300 flanges is incluaed in the minimum flange thickness given above, but other raised faces must be added thereto. Class 150 loose flanges are thicker than integral flanges for sizes 31f,..inch and smaller. Note column B. Lengths of alloy steel stud bolts do not include the height of the points.

  Class, Steel, Dimensions, Flange, Class 150, Steel flange dimensions t

Calculated Flange Weights in Pounds Class 150

Calculated Flange Weights in Pounds Class 150 Nominal Pipe Size Outside Diameter (Inches) Slip-On / Threaded Socket Weld Weld Neck Blind Lap-Joint 1/2 3.50 2 2 2 2 3/4 3.88 2 2 2 2 1 4.25 2 2 2 2 1 1/4 4.62 3 4 3 3 1 1/2 5.00 3 5 4 3 2 6.00 5 9 4 5 2 1/2 7.00 7 11 11 7 3 7.50 8 14 14 8 3 1/2 8.50 11 15 13 11 4 9.00 13 16 19 13 5 10.00 15 21 21 ...

  Class, Flange, Class 150