MATERIAL DATASHEET Composites

markforged.com 480 Pleasant St, Watertown, MA 02472 Composites MATERIAL DATASHEET Plastic Matrix Test (ASTM) Onyx Onyx FR Nylon W Tensile Modulus (GPa) D638 1.4 1.3 1.7 Tensile Stress at Yield (MPa) D638 36 29 51

MATERIAL DATASHEET 17-4 PH Stainless Steel

17-4 PH Stainless Steel ADDITIONAL DATA Values listed below compare Markforged samples processed in three different ways: As-Sintered, heat treated to H900 standard, and heat treated to H1150 standard. These representative data were tested, measured, or calculated using standard methods and are subject to change without notice.

  Steel, 17 4

MATERIAL DATASHEET 17-4 PH Stainless Steel

17-4 PH Stainless Steel ADDITIONAL DATA Values listed below compare Markforged samples processed in three different ways: As-Sintered, heat treated to H900 standard, and heat treated to H1150 standard. These representative data were tested, measured, or calculated using standard methods and are subject to change without notice.

  Steel, 17 4

MATERIAL DATASHEET H13 Tool Steel - Markforged

Ultimate Tensile Strength ASTM E8 1420 MPa 1500 MPa 1580 MPa 0.2% Yield Strength ASTM E8 800 MPa 1250 MPa 1360 MPa Elongation at Break ASTM E8 5% 5% 14% Hardness ASTM E18 40 HRC 45 HRC 46 HRC Relative Density ASTM B923 94.5% 94.5% 100% Composition Amount Chromium 4.7-5.5% Molybdenum 1.3-1.7% Silicon 0.8-1.2% Vanadium 0.8-1.2% …

  Astm, 2015

MATERIAL DATASHEET 17-4 PH Stainless Steel - Markforged

Carbon 0.07% max Phosphorous 0.04% max Sulfur 0.03% max Iron bal Markforged H900 Heat Treated 17-4 PH stainless steel processed with the Markforged Metal X system heat treated to H900 specification. ASTM A564 H900 Heat Treated ASTM A564 17-4 PH stainless steel heat treated to H900 specification. MIM H900 Heat Treated

  Steel, Carbon, 17 4

Design Guide for 3D Printing with Composites - Markforged

process. Unless otherwise specified, data is based on parts printed on Markforged composite printers at 100 micron layer height in Onyx with default print settings. Minimum part dimensions X: 1.6 mm (0.063”) Y: 1.6 mm (0.063”) Z: 0.8 mm (0.031”) Minimum part size is limited to the extrusion width and height of each bead. The

  Based, Composite

DuPont Delrin acetal resin Molding Guide

3 • Hold-up areas—in cylinder, adapter, nozzle, screw tip, hot runner and check valve assembly • Plugged nozzle—from scrap metal or higher melting point

  Guide, Dupont, Molding, Molding guide

Joining of Plastics and Composites

UNESCO – EOLSS SAMPLE CHAPTERS WELDING ENGINEERING AND TECHNOLOGY - Joining of Plastics and Composites - Mladen Sercer, Pero Raos ©Encyclopedia of Life Support Systems (EOLSS)

  Engineering, Plastics, Composite, Joining, Joining of plastics and composites

Chemical Resistance Guide - Gilson Eng

1. INTRODUCTION. Thermoplastics and elastomers have outstanding resistance to a wide range of chemical reagents. The chemical resistance of plastic piping is basically a function of the thermoplastic material and the compounding components.

  Resistance, Chemical, Chemical resistance, Thermoplastic

Long Fiber Reinforced Thermoplastics - Hi Polymers

Long Fiber Reinforced Thermoplastics Injection Molding Guide Plastic Materials Celstran & Injection Molding Process & Handling Trouble Shooting Guide

  Brief, Long, Reinforced, Thermoplastic, Long fiber reinforced thermoplastics

Advanced Materials Araldite 2000+ Adhesives

Design Flexibility Dissimilar Materials – Unlike welding, Araldite® 2000+ Adhesives can join metals to plastics, aluminum to steel, or a variety of other materials.

  Material, Advanced, Araldite, Advanced materials araldite

General Information on Properties - ProPolymers …

Figure 10 Tensile strength at 23°C after heat aging at 150°C for Stanyl and competitive thermoplastics. Table 2 Heat aging resistance as expressed by the CUT and ARO-concept and stiffness at

  General, Information, Properties, Thermoplastic, General information on properties