PDF4PRO ⚡AMP

Modern search engine that looking for books and documents around the web

Example: stock market

Bitumastic 300M - Carboline

Bitumastic 300 MPRODUCT DATA SHEET November 2021300 MPage 1 of 4 SELECTION & SPECIFICATION DATA Generic TypeCoal tar epoxy DescriptionRenowned high build coal tar epoxy for protection of steel and concrete in single or two-coatapplications in a broad variety of aggressive industrial applications. Features Excellent chemical, corrosion and abrasion resistance High build, 400 to 600 microns in a single coat (up to 875 microns with force curing) Compatible with controlled cathodic protection Suitable for use in exposures as referenced in the following specifications Corp of Engineers C-200, C200a AWWA C-210 for exterior SSPC-Paint 16 Steel Tank Institute Corrosion Control System STI-P3 ColorBlack and Red PrimerSelf-priming, or use suitable primer as

* Disclaimer: Bitumastic 300M is a proprietary formula that is not necessarily formulated to the exact compositional guidelines set forth in some of these standards. Major deviations that control and improve application characteristics may be present, but does not have a detrimental effect on the suitability for use outlined ...

Fullscreen Download
Loading..

Tags:

  030m, Bitumastic 300m, Bitumastic

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Spam in document Broken preview Other abuse

Transcription of Bitumastic 300M - Carboline

Documents from same domain

Carbomastic 15 - Carboline

msds.carboline.com

Generic Type Epoxy Mastic Description Aluminium-pigmented, low-stress, high solids mastic with a proven field history. Carbomastic 15 was the pioneer mastic coating in a number of industrial markets and today still provides unmatched levels of barrier protection and corrosion resistance over existing finishes and rusted or

  Mastic, Carbomastic 15, Carbomastic

Carbozinc 859 - Carboline

msds.carboline.com

Generic Type Organic Zinc Rich Epoxy Description Low VOC organic zinc epoxy steel primer with extremely fast cure-to-topcoat characteristics for in-shop applications and quick turnaround requirements in the field. Carbozinc 859 has less than 360g/litre VOC (thinned) and is used extensively in virtually all industrial markets. Features

  Zinc, Carbozinc, Carbozinc 859

Carbozinc 11 HS - Carboline

msds.carboline.com

These are nominal values. When used as a pre-construction primer thin up to 38 oz/gal using exempt Thinner 236 E. Topcoats Acrylics, Epoxies, Polyurethanes, High Heat Silicones, Silicates and others as recommended by your Carboline sales representative. Not required for certain exposures. A mist-coat/full-coat spray technique is often required to

  Itsm, Carbozinc, Carbozinc 11 hs

Carboguard 893 - Carboline

msds.carboline.com

Brush Use a medium bristle brush. Roller Use a short-nap synthetic roller cover with phenolic core. APPLICATION CONDITIONS Condition Material Surface Ambient Humidity Minimum 4°C (40°F) 4°C (40°F) 4°C (40°F) 0% Maximum 32°C (90°F) 57°C (135°F) 43°C (110°F) 90% This product simply requires the substrate temperature to be above the ...

  Blister, Carboguard, Carboguard 893

Carbothane 134 HG - Carboline

msds.carboline.com

24°C (75°F) 8 Hours 8 Hours 7 Days 32°C (90°F) 4 Hours 4 Hours 5 Days These times are based on a 50 micron dry film thickness. Higher film thickness, insufficient ventilation or cooler temperatures will require longer cure times and could result in solvent entrapment and premature failure. *Maximum self-recoat times are indefinite.

  Carbothane 134 hg, Carbothane

Carbothane 134 - Carboline

msds.carboline.com

NOTE: Substitute thinners, especially Lacquer Thinners, may contain alcohols which will inhibit the cure of Carbothane 134. Use of thinners other than those supplied or approved by StonCor Africa may adversely affect product performance and void product warranty, whether express or implied. Ratio 8:1 Pot Life

  Carbothane, Thinner, Carbothane 134

Thermaline 450 EP - Carboline

msds.carboline.com

Surface profile should be a dense angular 1-3 mils and is best achieved through abrasive blasting. Remove all contaminants that would interfere with the performance of stainless steel for the intended service such as, but not limited to, imbedded iron or chlorides.

  Abrasive, Blasting, Abrasive blasting, 450 ep

Carboguard 890 - Carboline

msds.carboline.com

January 2019 890 Page 2 of 4 SUBSTRATES & SURFACE PREPARATION General Surface must be clean and dry. Remove all dirt, dust, oil and all other contaminants. Steel Immersion: ISO 8501 Sa2½ Non-immersion: ISO 8501 Sa2½ 40 to 75µm ISO 8501 St2 or St3 are suitable cleaning methods for mild environments. Galvanized Steel

  Surfaces, Preparation, Steel, Mild, Surface preparation, Carboguard, Carboguard 890

SELECTION & SPECIFICATION DATA - Carboline

msds.carboline.com

to these guidelines to achieve the desired results. Spray Application (General) The following spray equipment has been found suitable and is available from equipment manufacturers. Keep material under mild agitation during application. If spraying stops for more than 10 minutes, recirculate the material remaining in the spray line.

  Guidelines, Data, Specification, Material, Selection, Selection amp specification data

Carboguard 635 - Carboline

msds.carboline.com

Potable Water Use: (0200) Beige, (0700) Grey and (0800) White Other Colours: Red and Black Gloss Satin Primer Self-priming Recommended Thickness 100 to 150 microns per coat Solid(s) Content By Volume: 65% ± 2% Theoretical Coverage Rates 25.6m²/litre at 25 microns 6.4m²/litre at 100 microns 4.3m²/litre at 150 microns Allow for loss in mixing ...

  Water, Carboguard, Carboguard 635