PDF4PRO ⚡AMP

Modern search engine that looking for books and documents around the web

Example: stock market

Carbozinc 859 - Carboline

Carbozinc 859 PRODUCT DATA SHEET September 2018CZ859 Page 1 of 4 SELECTION & SPECIFICATION DATA Generic TypeOrganic Zinc Rich Epoxy DescriptionLow VOC organic zinc epoxy steel primer with extremely fast cure-to-topcoat characteristics forin-shop applications and quick turnaround requirements in the field. Carbozinc 859 has less than360g/litre VOC (thinned) and is used extensively in virtually all industrial markets. Features Meets Class B slip co-efficient and creep testing criteria for use on faying surfaces.

Flash Point (Pensky Martens Closed Cup) Part A: 9°C Part B: 3°C Zinc Filler: N/A Storage Store indoors. This product is solvent-based and not affected by excursions below these published storage temperatures, down to -12°C, for a duration of …

Fullscreen Download

Tags:

  Closed, Entram, Pensky, Carbozinc, Carbozinc 859, Pensky martens closed cup

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Spam in document Broken preview Other abuse

Transcription of Carbozinc 859 - Carboline

Documents from same domain

Bitumastic 300M - Carboline

msds.carboline.com

Bitumastic 300M PRODUCT DATA SHEET November 2021 300M Page 2 of 4 PERFORMANCE DATA (TYPICAL VALUES) ASTM B117 Salt FogTest Method Blasted steel 2 Coats 300MSystem Results No blistering, rusting or delamination. No measurable undercutting at scribe after 2000 hours ASTM D2794 Impact Blasted steel 2 Coats 300M Impact site diameter, 9.5, 9.5, 12.7 ...

  030m, Bitumastic 300m, Bitumastic

Carbomastic 15 - Carboline

msds.carboline.com

Generic Type Epoxy Mastic Description Aluminium-pigmented, low-stress, high solids mastic with a proven field history. Carbomastic 15 was the pioneer mastic coating in a number of industrial markets and today still provides unmatched levels of barrier protection and corrosion resistance over existing finishes and rusted or

  Mastic, Carbomastic 15, Carbomastic

Carbozinc 11 HS - Carboline

msds.carboline.com

These are nominal values. When used as a pre-construction primer thin up to 38 oz/gal using exempt Thinner 236 E. Topcoats Acrylics, Epoxies, Polyurethanes, High Heat Silicones, Silicates and others as recommended by your Carboline sales representative. Not required for certain exposures. A mist-coat/full-coat spray technique is often required to

  Itsm, Carbozinc, Carbozinc 11 hs

Carboguard 893 - Carboline

msds.carboline.com

Brush Use a medium bristle brush. Roller Use a short-nap synthetic roller cover with phenolic core. APPLICATION CONDITIONS Condition Material Surface Ambient Humidity Minimum 4°C (40°F) 4°C (40°F) 4°C (40°F) 0% Maximum 32°C (90°F) 57°C (135°F) 43°C (110°F) 90% This product simply requires the substrate temperature to be above the ...

  Blister, Carboguard, Carboguard 893

Carbothane 134 HG - Carboline

msds.carboline.com

24°C (75°F) 8 Hours 8 Hours 7 Days 32°C (90°F) 4 Hours 4 Hours 5 Days These times are based on a 50 micron dry film thickness. Higher film thickness, insufficient ventilation or cooler temperatures will require longer cure times and could result in solvent entrapment and premature failure. *Maximum self-recoat times are indefinite.

  Carbothane 134 hg, Carbothane

Carbothane 134 - Carboline

msds.carboline.com

NOTE: Substitute thinners, especially Lacquer Thinners, may contain alcohols which will inhibit the cure of Carbothane 134. Use of thinners other than those supplied or approved by StonCor Africa may adversely affect product performance and void product warranty, whether express or implied. Ratio 8:1 Pot Life

  Carbothane, Thinner, Carbothane 134

Thermaline 450 EP - Carboline

msds.carboline.com

Surface profile should be a dense angular 1-3 mils and is best achieved through abrasive blasting. Remove all contaminants that would interfere with the performance of stainless steel for the intended service such as, but not limited to, imbedded iron or chlorides.

  Abrasive, Blasting, Abrasive blasting, 450 ep

Carboguard 890 - Carboline

msds.carboline.com

January 2019 890 Page 2 of 4 SUBSTRATES & SURFACE PREPARATION General Surface must be clean and dry. Remove all dirt, dust, oil and all other contaminants. Steel Immersion: ISO 8501 Sa2½ Non-immersion: ISO 8501 Sa2½ 40 to 75µm ISO 8501 St2 or St3 are suitable cleaning methods for mild environments. Galvanized Steel

  Surfaces, Preparation, Steel, Mild, Surface preparation, Carboguard, Carboguard 890

SELECTION & SPECIFICATION DATA - Carboline

msds.carboline.com

to these guidelines to achieve the desired results. Spray Application (General) The following spray equipment has been found suitable and is available from equipment manufacturers. Keep material under mild agitation during application. If spraying stops for more than 10 minutes, recirculate the material remaining in the spray line.

  Guidelines, Data, Specification, Material, Selection, Selection amp specification data

Carboguard 635 - Carboline

msds.carboline.com

Potable Water Use: (0200) Beige, (0700) Grey and (0800) White Other Colours: Red and Black Gloss Satin Primer Self-priming Recommended Thickness 100 to 150 microns per coat Solid(s) Content By Volume: 65% ± 2% Theoretical Coverage Rates 25.6m²/litre at 25 microns 6.4m²/litre at 100 microns 4.3m²/litre at 150 microns Allow for loss in mixing ...

  Water, Carboguard, Carboguard 635

Related documents

Flash points of aqueous solutions of flammable solvents

www.icheme.org

The flash points were determined using a Sommer and Runge PMA2 Automatic Pensky-Martens Closed Cup Flash Point Tester supplied by Gallenkamp. The procedure used was similar to that described in the relevant British3, American4 and European5 Standards. However, as the standard Pensky-Martens Closed Cup Flash Point Tester is designed

  Closed, Entram, Pensky, Pensky martens closed cup

SAFETY DATA SHEET

www.castrol.com

Closed cup: 204°C (399.2°F) [Pensky-Martens.] Not available. Not available. Viscosity Kinematic: 121.8 mm2/s (121.8 cSt) at 40°C Kinematic: 15.8 mm2/s (15.8 cSt) at 100°C Odor threshold Not available. Partition coefficient: n-octanol/water Appearance Boiling point Not available. Lower and upper explosive (flammable) limits Not available.

  Closed, Entram, Pensky, Closed cup

Standard Test Method for Flash and Fire Points by ...

www.sepehrshimi.com

D93Test Methods for Flash Point by Pensky-Martens Closed Cup Tester D 140 Practice for Sampling Bituminous Materials D 1310 Test Method for Flash Point and Fire Points of Liquids by Tag Open-Cup Apparatus D 4057 Practice for Manual Sampling of Petroleum and Petroleum Products D 4177 Practice for Automatic Sampling of Petroleum and Petroleum ...

  Closed, Entram, Pensky, Pensky martens closed cup

Related search queries

Pensky-Martens Closed Cup, Closed cup, Pensky, Martens