DESIGN OF MACINE ELEMENTS- II - Rajagiri School of ...
Design of V-belt drives, Advantages and limitations of V-belt drive (3) Selection of roller chains, power rating of roller chains, galling of roller chains, polygonal action, silent chain. (3) 6 Connecting rod –material, connecting rod shank, small end, big end, connecting rod bolts, inertia bending stress, piston (5)
Tags:
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
DESIGN OF MACHINE ELEMENTS - Rajagiri School of ...
www.rajagiritech.ac.inLateral rigidity: Ability to resist deflection under the action of external forces ... angular misalignment •Absorbs vibrations •Used for transmitting high torques. Flexible Coupling: Animation Department of Mechanical Engineering 23. …
DESIGN OF MACHINE ELEMENTS - Rajagiri School of ...
www.rajagiritech.ac.inScrew Threads: Standards Department of Mechanical Engineering 7 B.S.W thread: Symmetrical V thread with thread angle 55 deg. Used in bolts and screwed fastenings B.A thread: B.S.W threads with fine pitches. Instruments and other precision works American national standard thread: Flat crest and roots. General
American, National, Screw, Thread, Screw thread, American national
MODULE 5 SHEET METAL OPERATIONS
www.rajagiritech.ac.inSheet bending Sheet bending is defined as the straining of the metal around a straight axis. During bending operation, the metal on the inner side of the neutral plane is compressed, and the metal on the outer side of the neutral plane is stretched. Bending causes no change in the thickness of the sheet metal.
Sheet, Metal, Bending, Sheet metal, Sheet bending sheet bending
Radiography Testing - Rajagiri School of Engineering ...
www.rajagiritech.ac.inapplications including medicine, engineering, forensics, security, etc. •In NDT, radiography is one of the most important and widely used methods. •Radiographic testing (RT) offers a number of advantages over other NDT methods, however, one of its major disadvantages is the health risk associated with the radiation.
Refrigeration and Air conditioning
www.rajagiritech.ac.in•Air conditioning systems - room air conditioner - split system - packaged system - all air system - chilled water system. Winter air conditioning - factors affecting heating system, humidifiers. Year round air conditioning. AC system controls - thermostat and humidistat. •Air distribution systems - duct system and
REPORT (2014-2017) DEPARTMENT OF ELECTRICAL & …
www.rajagiritech.ac.indevelopment in the particular area. Figure 3: Process of filling gaps in syllabus Syllabus Subject teachers Analysis by course experts Course outcome & its correlation with programme outcomes Gaps in syllabus identified Assessment committe Department Advisory Board
TYPES OF GRINDING WHEELS
www.rajagiritech.ac.inSurface grinding machine Machine may be similar to a milling machine used mainly to grind flat surface Basically there are four different types of surface grinding machines characterized by the movement of their tables and the orientation of grinding wheel spindles •Horizontal spindle and reciprocating table
BASICS OF HEAT TRANSFER - Rajagiri School of Engineering ...
www.rajagiritech.ac.inUnderstand the basics of Heat pipe, Boiling and Condensation[3] 5. ... This happens from solids, liquids and gases. ... The mechanism of heat flow by radiation consists three distinct phases: 1. Conversion of thermal energy of the hot source into electromagnetic waves.
FORGING
www.rajagiritech.ac.inRoll forging In this process, the bar stock is reduced in cross-section or undergoes change in cross-section when it is passed through apair of grooved rolls made of die steel. This process serves as the initial processing step for forging of parts such as connecting rod, crank shaft etc.
MULTI-STAGE VAPOUR COMPRESSION REFRIGERATION …
www.rajagiritech.ac.in•A multi-stage system is a refrigeration system with two or more low-side pressures. •Multi-stage systems can be classified into: a) Multi-compression systems b) Multi-evaporator systems c) Cascade systems, etc. •Two concepts which are normally integral to multi-pressure systems are, i) flash gas removal, and ii) intercooling.
Related documents
Series 90 100 cc Axial Piston Pump Parts Manual
www.moorepumps.comThe modular design of Series 90 units results in a simplified service parts list and part number identification procedure. The same item numbers are used for same part names on all units within a product type. ... Series 90 100 cc Axial Piston Pump. 87. 100. No. end.
Series 90 Axial Piston Pumps Technical Information Manual
www.precisionfluidpower.comSeries 90 motors also use the parallel axial piston/slipper design in conjunction with a fixed or tiltable swashplate. They can intake/discharge fluid through either port; they are bidirectional. They also include an optional loop flushing feature that provides additional cooling and cleaning of fluid in the working loop.
HPV-02. Variable pumps for closed loop operation.
www.linde-hydraulics.comDesign characteristics >> axial piston pump in swashplate design for high pressure closed loop systems >> clockwise or counter clockwise rotation >> exact and rugged servo control devices (mechanical, hydraulic, electro-hydraulic) >> integrated …
Operations, Design, Loops, Pumps, Piston, Variable, Closed, Axial, Axial piston, Variable pumps for closed loop operation
Brueninghaus Hydromatik Rexroth A10VO & A10VSO pump
hydpump.com– Axial piston pump A10SO, variable, in swash plate design for hydrostatic transmissions in open loop circuit – Flow is proportional to drive speed and displacement. By adjusting the swash plate angle it is possible to infinitely vary the flow – Mounting flange acc. to SAE J744 – Flanged ports acc. to SAE J518 – 2 case drain ports
Axial piston variable pump AA4VG Series 32
dc-us.resource.bosch.comAxial piston unit 01 Swashplate design, variable, nominal pressure 5800 psi (400 bar), maximum pressure 6500 psi (450 bar) AA4V Operating mode 02 Pump, closed circuit G Size (NG) 03 Geometric displacement, see “Technical data” on page 8 in3/rev. 1.71 2.44 3.42 4.33 5.49 7.63
Q Series Piston Pumps - Power management solutions | Eaton
www.eaton.com13,14 Pump design 20 Design number subject to number change. Installation dimensions remain unchanged for designs 10-19. 15,16 Control type C** Pressure compensator. PVQ10: Standard model is C21, indicating setting of 210 bar (3000 psi); range is 02-21 in tens of bar (350-3000 psi). PVQ13: Standard model is C14, indicating factory setting
API Standard 670
www.api.orgshaft vibration, casing vibration, shaft axial position, shaft rotational speed, piston rod drop, phase reference, overspeed, surge detection, and critical machinery