Solid State Relays Common Precautions

2.Inductive Noise Do not wire power lines alongside the input lines. Inductive noise may cause the SSR to malfunction. If inductive noise is imposed on the input terminals of the SSR, use the following cables according to the type of inductive noise, and reduce the noise level to less than the must release voltage of the SSR.

  Power, Noise, Reduces

G2R - Omron

3 G2R PCB Power Relay G 2 R Quick-connect Terminal (#187) Full-wave Rectifier For Ultrasonically Cleanable Note: When ordering, add the rated coil voltage to the model number. Example: G2R-1A-T AC12 However, the notation of the coil voltage on the produc t case as well as on the packing will be marked as @@ VAC.

  Terminal

CSM PCB Con CN J 1 3 - omronfs.omron.com

A-20 最新の商品情報・便利な情報は www.fa.omron.co.jp/ コネクタ 共通の注意事項 コネクタ 共通の注意事項 挿抜作業について ・通電中の挿抜作業時および抜去後に、コネクタの接点 …

  Nomor

CSM XM2 XM3 AC DS J 1 8 - omronfs.omron.com

2 最新の商品情報・便利な情報は www.fa.omron.co.jp/ XM2/XM3 Dサブコネクタ X M 2 ／ X M 3 注1. 1個のコネクタに固定具は2個必要です。 注2. 形XM3K/Lには取付できません。

  Nomor

Solid State Pressure Sensors D8M - omronfs.omron.com

Compact D8M solid state pressure sensors provide reliable detection for gas and air inflow for burner controls in water heaters, furnaces and other gas-fired devices.

  States, Solid, Sensor, Solid state

G5V-2 - omronfs.omron.com

2 G5V-2 Low Signal Relay G 5 V-2 Ratings Coil Note 1. The rated current and coil resistance are measured at a coil temperature of 23°C with a tolerance of ±10%. 2.Operating characteristics are measured at a coil temperature of 23°C.

G6B - Omron

3 G6B PCB Power Relay G 6 B Models for Ultrasonically Cleanable Note: When ordering, add the rated coil voltage to the model number. Example: G6B-1114P-US DC5 However, the notation of the coil voltage on the produc t case as well as on the packing will be marked as @@ VDC.

DC Power Relays

High-voltage, High-current Loads • A compact relay (73 x 36 x 67.2 mm (L x W x H)) capable of switching 400-V 60-A DC loads. (Capable of interrupting 600 A at 300 VDC max.) • The switching section and driving section are gas-injected and hermetically sealed, allowing these compact relays to interrupt high-capacity loads.

  High, Voltage

G2RL - Omron

Test conditions: Shock is applied in ±X, ±Y, and ±Z directions three times each with without energizing the relays to check the number of malfunctions. Requirement: None malfuction 100 m/s2 Sample: G2RL-24 12 VDC Number of relays: 5 pcs Test conditions: Shock is applied in ±X, ±Y, and ±Z directions three times each with without energizing

  Tests

G6S - Omron

Electrical 100,000 operations min. for AC (at 1,800 operations/h with rated load) 100,000 operations min. for DC (at 1,200 operations/h with rated load) Failure rate (P level) (reference value) *3 10 μA at 10 m VDC Ambient operating temperature-40°C to 85°C (with no icing or condensation), and -40°C to 70°C (with no icing or condensation)

  Electrical

Valve terminal 2 Design The valve terminal VTUG- has the ...

2 Earth terminal (hole for the earthing screw) Fig. 2 2.1 Valve terminal VTUG-…-M The valve terminal VTUG-...-M (multi-pin node) has the following additional con­ necting component. 1 1 Electrical multi-pin plug connection (Sub-D or ribbon cable) Fig. 3 2.2 Valve terminal VTUG-…-V

  Screw, Terminal

DINnectors Single-Level Terminal Blocks

ttt Terminal Blocks tTBL-86 1-800-633-0405 t tt ttt DINnector Marking Tags Cross Reference - Screw-type Block Type DN-L DN-LA DN-LT DN-LAT DN-EMLBL DN-T12 X DN-T10 X DN-T8 X DN-T6 X DN-T4 X DN-T1/0 X DN-T3/0 X DN-D10 X DN-D10X X DN-D10LED X DN-D10DR X DN-TL14 X DN-THERM X DN-EMXM1 X DN-EMXDV X DN-M10 X DN-MG10 X DN-G10 X DN-G8 X DN-G6 X DN-G4 X DN-G1/0 X DN-F6 X DN-F10 X DN-DIS2 X DN-DIS4 X DN ...

  Screw, Terminal

USB-6212 Specifications - National Instruments

Screw Terminal 32 total, 16 (P0.<0..15>), 16 (PFI <0..7>/P1.<0..7>, PFI <8..15>/P2.<0..7>) Ground reference D GND Pull-down resistor 50 kΩ typical, 20 kΩ minimum Input voltage protection ±20 V on up to 8 pins1 PFI Functionality Functionality Static digital input, static digital output, timing input, timing output

  Specification, Screw, Terminal, Screw terminal

Terminals, Lugs, and Fasteners

side terminal batteries • Posts have 3/8" threaded stud to screw into side terminal batteries • 01477 fits 3/8" stud • Easy finger tight installation Part # Polarity Packaging Master Carton Quantity Weight 00575 Universal Clam Shell of 2 10 3 lbs. 05320 Universal Bulk 25 5 lbs. 05768 Positive Bulk 25 4 lbs. 05769 Negative Bulk 25 4 lbs.

  Screw, Terminal

KOBELCO INSTALLATION COMPRESSORS (AMERICA), INC ...

the operation of a rotary screw air compressor is inheritly dangerous. kobelco compressors (america), inc. has made every effort to provide you with a safe air compressor. only trained personnel, who have been designated, should operate and maintain this air compressor. failure to follow the enclosed instructions will

  Compressor, Screw, America

Grounding Techniques for Tactical Equipment and Systems

terminal, there are some visible parts connected to the metal chassis (ground) (see figure 1-3 on page 1-4). 1-9. The purpose of chassis ground is to connect (bond) individual items to the equipment grounding conductor in alternating current systems or negative in DC current systems.

  Terminal