Transistor Technologies for High Efficiency and Linearity

Differential Topology • Double the available voltage swing • Even-order harmonic suppression • Double the frequency of current injection into substrate –Reduce the potential for LO-pulling • The tail current source is removed from the standard differential pair (this is a “quasi-differential” structure) –DC current set by the biasing of input devices

Phase Locked Loop Circuits

Clock generation: B. Razavi, Design of Analog CMOS Integrated Circuits, Chap. 15, McGraw-Hill, 2001. 1. Definition. A PLL is a feedback system that includes a VCO, phase detector, and low pass filter within its loop. Its purpose is to force the VCO to replicate and track the frequency and phase at the input when in lock.

  System, Design

ADS Tutorial Stability and Gain Circles ECE145A/218A

equations. The syntax is: gp_circle(S, gain, # points on circle) where S is the S-parameter matrix. Let’s illustrate. In the example below, a table is used to display frequency, maximum stable gain (MSG), the stability factor, k, and the magnitude of delta. The gain circles are at MSG (MaxGain1 in this case), and 1 and 2 dB below MSG.

  Stability, Gain, Tutorials, Circle, Tutorial stability and gain circles ece145a, Ece145a, Gain circles

Audio Amplifier Circuit - UC Santa Barbara

Week #1: Audio amplifier Week #2: Microphone circuit The audio amplifier project is more difficult and time-consuming than the microphone pre-amp, so part of week #2 may be used to finish the audio amp. All breadboarding and testing can and should be done in lab. Soldering and hardwiring can and should be done outside lab.

  Audio

Quality factor, Q

When a resonant circuit is connected to the outside world, its total losses (let’s call them RP or GP) are combined with the source and load resistances, RS and RL. For example, Here is a parallel resonant circuit (C,L and RP)connected to the outside. The total Q of this circuit is called the loaded Q or QL and is given by

  Parallel, Resonant, Parallel resonant

Latches, the D Flip-Flop & Counter Design

February 6, 2012 ECE 152A - Digital Design Principles 2 Reading Assignment Brown and Vranesic 7Flip-Flops, Registers, Counters and a Simple Processor 7.1 Basic Latch 7.2 Gated SR Latch 7.2.1 Gated SR Latch with NAND Gates 7.3 Gated D …

  Latch, Sr latch

Flip-Flops and Sequential Circuit Design

11 Latches and Flip-Flops 11.5 S-R Flip-Flop 11.6 J-K Flip-Flop 11.7 T Flip-Flop 11.8 Flip-Flops with Additional Inputs 11.9 Summary 12 Registers and Counters 12.5 Counter Design Using S-R and J-K Flip-Flops 12.6 Derivation of Flip-Flop Input Equations – Summary

  Flip, Flops, Latches, Latches and flip

BASICS OF THE SPECTRUM ANALYZER - UC Santa Barbara

Fourier ⋅ π → − + + Now instead of a bank of narrow filters, we shall have one narrow filter centered at a fixed frequency, say fI, and we shall scan the signal spectrum across this filter by multiplying x(t) by a sinusoid of varying frequency f0. See Figure 1. …

  Basics, Spectrum, Analyzer, Fourier, Spectrum analyzer

Mealy and Moore Machines

February 22, 2012 ECE 152A - Digital Design Principles 5 Finite State Machines Two types (or models) of sequential circuits (or finite state machines) Mealy machine Output is function of present state and present input Moore machine Output is function of present state only Analysis first, then proceed to the design of

  States, Design, Machine, Finite, Finite state

Number Representation and Computer Arithmetic

One way to encode decimal digits using binary signals is to encode each of the digits 0-9 by means of its 4-bit binary representation. The resulting binary-coded decimal (BCD) representation is shown below:

  Medical, Coded, Binary, Arithmetic, Binary coded decimal

Holistic FMEDA-Driven Safety Design and Verification for ...

The Midas Safety Platform (Figure 2) is a key technology to enable a FMEDA-driven safety methodology and flows. In addition, the Cadence Legato™ Reliability Solution, including an analog defect identification and simulation approach based on the

  Simulation, Driven

Understanding Motion Simulation - SolidWorks

A simulation of the motion of the inverted slider mechanism shown in Figure 3 presents an exercise commonly found in textbooks on the kinematics of machines. Here, the objective is to find the angular speed and the acceler- ... SlIdEr And drIVEn lInk. Engineers can represent simple mechanisms such as the elliptic trammel or inverted slider ...

  Simulation, Driven, Solidworks

The Globalization of Religion - Oakland University

This simulation will focus on the globalization of religion. Religions have crossed many boundaries, having been spread by immigrants, refugees, aggressors, or by the founders of this ... The economic growth of religions has also been driven by technology since mass media can be used to spread the word and provide many of the benefits of church ...

  Simulation, Driven

HSPICE User Guide: Simulation and Analysis

HSPICE® User Guide: Simulation and Analysis Version B-2008.09, September 2008

  Hspice, Simulation