International Building Code: Smoke Door Requirements
In the past, a solid core door with minimal clear-ances required for proper operation was thought to provide this effective barrier. However, the IBC 2009 Commentary states in Section 711.5.2, describing the air infiltration requirements for smoke and draft control doors, that “section 407.3.1 requires corridor doors in
Tags:
Draft, Control, Requirements, Doors, Smoke, Smoke and draft control, Smoke door requirements
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
Decoded - idighardware.com
idighardware.comDecoded. 2015 International Building Code 2015 NFPA 101 - The Life Safety Code Delayed Egress Controlled Egress Delayed Egress Controlled Egress Code Section 1010.1.9.7 - Delayed Egress 1010.1.9.6 Controlled egress doors in Groups I-1 and I-2 7.2.1.6.1 - Delayed Egress Locking Systems
Mounting Heights for Door Hardware
idighardware.comCourtesy of the Steel Door Institute table 5 – hardware Locations Locks, Latches, Roller Latches and Double Handle Sets 38" – 42" (965 mm – 1067 mm) Centerline of Lock Strike from Bottom of Frame Rim and Mortise Panic Devices Cylindrical and Mortise Deadlocks(1) 48" (1219 mm) to Centerline of Strike from Bottom of Frame
Hardware, Doors, Mounting, Sets, Height, Mounting heights for door hardware
DECODED: Calculating the Egress Width of Door Openings
idighardware.comcalculate egress capacity is the same, but the egress capacity factors vary slightly from those of the IBC: For non-sprinklered healthcare occupancies, the egress capacity factor is 0.5 inches per occupant. For occupancies with high-hazard contents, …
DECODED: Calculating the Occupant Load
idighardware.comDECODED: From the well-known blog idighardware.com, Lori Greene brings some much-needed clarity to codes. Calculating the Occupant Load BY LORI GREENE, AHC/CDC, FDAI, FDHI, CCPR ANY CODE REQUIREMENTS ARE DEPENDENT UPON THE OCCUPANT load of the room or space in question.
DECODED: Calculating the Occupant Load - I Dig Hardware
idighardware.comoccupancy may include chairs that are not fixed, and the occupant load factor is 7 net square feet per person. According to the International Building Code (IBC), standing space is calculated using an occupant load factor of 5 net square feet per person. When an Assembly occupancy includes tables and chairs, it is typically considered a less
Related documents
2010 FLORIDA BUILDNG CODE, FIRE AND LIFE SAFETYi
www.floridabuilding.orgSmoke Barriers (§710.5). Exception 1 modified to allow ¾ inch undercuts in smoke barrier doors in Group I-2. Smoke Partitions (§711.5.2). Removes language requiring artificial bottom seal across full width of bottom of door when testing smoke and draft control doors in smoke partitions. (§711.5) Horizontal Assemblies. Eliminates fire resistance
Draft, Control, Doors, Smoke, Assemblies, Smoke and draft control
S D I TECHNICAL DATA SERIES 118 19 - Steel Door Institute
steeldoor.orgThese door and frame assemblies divide occupancies in a building. 1 Hour 3/4 Hour (45 minute) For use where there are openings in corridors or room partitions. 2 Hour ... smoke and draft control is a primary concern. 2.7 Doors tested without hose stream Doors may be rated as 20 minutes without a hose stream. These doors have successfully
Draft, Control, Doors, Smoke, Assemblies, Smoke and draft control
7500 SERIES - Norton Door Controls
www.nortondoorcontrols.com• It is strongly recommended, and it is required on fire door assemblies, that doors having a door closer be hung on ball-bearing or anti-friction hinges or pivots • Failure to use the correct type and size fasteners may void factory warranty • Fasteners for fire/smoke door assemblies must conform to NFPA 80.
Doors, Smoke, Assemblies, Door assemblies, Smoke door assemblies
draft) - ASDMA
www.asdma.com3.6 Smoke control doorsets Approved document B requires that certain door assemblies meet smoke control requirements and in order to do this the doorset will require seals to be provided at the jambs, head, and in the case of pairs, the meeting stiles.
Draft, Control, Doors, Smoke, Assemblies, Smoke control, Door assemblies, Masad
MASTER SPECIFICATIONS Division 08 OPENINGS
www.northwestern.edu1. Smoke- and Draft-Control Assemblies: Provide an assembly with gaskets listed and labeled for smoke and draft control by a qualified testing agency acceptable to authorities having jurisdiction, based on testing according to UL 1784 and installed in compliance with NFPA 105.
Draft, Control, Smoke, Assemblies, Smoke and draft control, Control assemblies, And draft
Basic Fire Door Requirements - ASSA ABLOY Academy
www.assaabloyacademy.comThese openings are in corridors where smoke and draft control is required. The minimum wall rating is 1 hour. Table 1 – Fire door openings 1 Introduction Fire testing of doors and hardware and the resulting labeling authorities granted, is a com-plex subject that is better understood when basic rules and guidelines are applied. 2 Doors
Smoke Barrier and Smoke Partition ... - Door Gap Gauge
doorgapgauge.comSmoke and draft control doors complying with UL 1784 shall be labeled as such. Labels shall be approved and permanently affixed. The label shall be applied at the factory or location where fabrication and assembly are performed. 715.3.5.3 Smoke and draft control door labeling requirements. Smoke and draft control doors complying with UL 1784 ...
Draft, Control, Doors, Smoke, Smoke and draft control, Smoke and draft control door
Architectural Woodwork Standards doors 9
woodworkinstitute.comedge guards. The door manufacturer is often a valuable assistant in these matters. Contract documents shall: • Specify neutral pressure or positive pressure compliance. • If positive pressure, specify the category of door: A or B assembly. • Specify whether the smoke and draft label (S label) is validated or not. FAce MAterIAl selectIon
Architectural Door Closer - Norton Door Controls
www.nortondoorcontrols.comProvides a smooth constant control of the door through its full opening and closing cycle. 180° door swing can be achieved when door, frame, hardware and arm function do not interfere. Non-handed With few exceptions all series 8301/ 8501 door closers are non-handed and can be installed on either right- or left-hand swing doors.