AWS EDITION 1, 2009 - Woodwork Institute

as registered AIA/CES instructors, they also provide numerous hours of standards/quality assurance/industry-based education. Additionally, our DAS’s are available as an unbiased, industry consultation service.

  Standards, Quality, Edition

Architectural Woodwork Standards millwork 6

©2014 AWI | AWMAC | WI 2nd Edition, October 1, 2014 Architectural Woodwork Standards 131 section 6 Millwork 6 introductory information Guide specifications are available through the sponsor associations in interactive digital format

Architectural Woodwork Standards ... - Woodwork Institute

©2014 AWI | AWMAC | WI 2nd Edition, October 1, 2014 Architectural Woodwork Standards 73 SECTION 4 Sheet Products 4 introductory information INTRODUCTION Section 4 is the second “material” section.

  Material

Architectural Woodwork Standards finishing 5

requirements. Choose performance characteristics which meet, but do not exceed, the needs of your project in the interest of value engineering. • Varying costs of finish systems typically relate directly to their performing characteristics. • Intermixing systems will likely cause quality and/or performance problems; they are usually

  Performance, Standards, Woodworks, Architectural, Architectural woodwork standards

SAMPLE ARCHITECTS ORIGINAL ... - Woodwork Institute

SAMPLE SHOP DRAWINGS NOTE: 1. THESE ARE SAMPLE DRAWINGS ONLY; ALL NAMES ARE FICTITIOUS. 2. MINIMUM SHEET SIZE REQUIRED BY W.I. IS 11” x 17”. 3. THESE DRAWINGS ILLUSTRATE DETAILS REQUIRED BY W.I. a. Refer to the Archetectural Woodwork Standards, Section 1, Submittals. 4. ALL INFORMATION INCLUDED IN THE …

  Woodworks

Architectural Woodwork Standards millwork 6

the architectural manufacturer can use several methods to fabricate radius moldings. Moldings applied to radii can be segmented, (typically only by direct specification) bent or steam bent, laminated and formed, preshaped, or machined to the radius. Manufacturers will fabricate the moldings in the longest practical lengths, with the

  Standards, Specification, Woodworks, Architectural, Architectural woodwork standards

2010 FLORIDA BUILDNG CODE, FIRE AND LIFE SAFETYi

Smoke Barriers (§710.5). Exception 1 modified to allow ¾ inch undercuts in smoke barrier doors in Group I-2. Smoke Partitions (§711.5.2). Removes language requiring artificial bottom seal across full width of bottom of door when testing smoke and draft control doors in smoke partitions. (§711.5) Horizontal Assemblies. Eliminates fire resistance

  Draft, Control, Doors, Smoke, Assemblies, Smoke and draft control

S D I TECHNICAL DATA SERIES 118 19 - Steel Door Institute

These door and frame assemblies divide occupancies in a building. 1 Hour 3/4 Hour (45 minute) For use where there are openings in corridors or room partitions. 2 Hour ... smoke and draft control is a primary concern. 2.7 Doors tested without hose stream Doors may be rated as 20 minutes without a hose stream. These doors have successfully

  Draft, Control, Doors, Smoke, Assemblies, Smoke and draft control

7500 SERIES - Norton Door Controls

• It is strongly recommended, and it is required on fire door assemblies, that doors having a door closer be hung on ball-bearing or anti-friction hinges or pivots • Failure to use the correct type and size fasteners may void factory warranty • Fasteners for fire/smoke door assemblies must conform to NFPA 80.

  Doors, Smoke, Assemblies, Door assemblies, Smoke door assemblies

draft) - ASDMA

3.6 Smoke control doorsets Approved document B requires that certain door assemblies meet smoke control requirements and in order to do this the doorset will require seals to be provided at the jambs, head, and in the case of pairs, the meeting stiles.

  Draft, Control, Doors, Smoke, Assemblies, Smoke control, Door assemblies, Masad

International Building Code: Smoke Door Requirements

In the past, a solid core door with minimal clear-ances required for proper operation was thought to provide this effective barrier. However, the IBC 2009 Commentary states in Section 711.5.2, describing the air infiltration requirements for smoke and draft control doors, that “section 407.3.1 requires corridor doors in

  Draft, Control, Requirements, Doors, Smoke, Smoke and draft control, Smoke door requirements

MASTER SPECIFICATIONS Division 08 OPENINGS

1. Smoke- and Draft-Control Assemblies: Provide an assembly with gaskets listed and labeled for smoke and draft control by a qualified testing agency acceptable to authorities having jurisdiction, based on testing according to UL 1784 and installed in compliance with NFPA 105.

  Draft, Control, Smoke, Assemblies, Smoke and draft control, Control assemblies, And draft

Basic Fire Door Requirements - ASSA ABLOY Academy

These openings are in corridors where smoke and draft control is required. The minimum wall rating is 1 hour. Table 1 – Fire door openings 1 Introduction Fire testing of doors and hardware and the resulting labeling authorities granted, is a com-plex subject that is better understood when basic rules and guidelines are applied. 2 Doors

  Draft, Control, Doors, Smoke, Smoke and draft control

Smoke Barrier and Smoke Partition ... - Door Gap Gauge

Smoke and draft control doors complying with UL 1784 shall be labeled as such. Labels shall be approved and permanently affixed. The label shall be applied at the factory or location where fabrication and assembly are performed. 715.3.5.3 Smoke and draft control door labeling requirements. Smoke and draft control doors complying with UL 1784 ...

  Draft, Control, Doors, Smoke, Smoke and draft control, Smoke and draft control door

Architectural Door Closer - Norton Door Controls

Provides a smooth constant control of the door through its full opening and closing cycle. 180° door swing can be achieved when door, frame, hardware and arm function do not interfere. Non-handed With few exceptions all series 8301/ 8501 door closers are non-handed and can be installed on either right- or left-hand swing doors.

  Control, Doors