PURLINS AND GIRTS - Canam Bâtiments

table, one row of discrete bracing is required at midspan. Therefore, Lt Step 4: Preliminary choice of a section Section choice: 356Z76-326M (1400Z300-128) Assumption: The standing seam roof, with connections at 24 in. (610 mm) c/c, provides partial lateral support of the Z section’s compression flange. Calculation of the positive moment

  Asme, Table, Roof, Standing, Standing seam roof

Canam - Steel Deck Catalogue (Canada)

our sales department. Most of the stainless steel types have a yield strength of 205 MPa (30 ksi). The resistance values of stainless steel deck are considered to be 90% of those shown in the tables. COATING Canam steel deck profiles are available with Z275 (G90) or ZF75 (A25) zinc protection according to the standard ASTM A 653M.

  Profile, Steel, Stainless, Stainless steel

MAIN TYPES OF PAINT USED WITH STEEL: STANDARDS ...

and certain types of intumescent coatings. Ideally, the application of a top coat should be done on the job site to minimize touchups from impacts that occur during transportation. Specialty paints Finishes other than the standard grey alkyd primers described above are commonly referred to as specialty paints.

  Intumescent

Steel Deck Diaphragm - Canam Bâtiments

CANAM PROFILES 8 P-3615 & P-3615 COMPOSITE PHYSICAL PROPERTIES Nominal Overall Gross Moment Type Thickness Depth Weight of Inertia mm mm kg/m2 mm4/m (in.) (in.) (lb./ft.2)(in.4/ft.) 22 0.76 37.4 8.50 228 227

HAMBRO COMPOSITE FLOOR SYSTEM - Canam Bâtiments

This manual has been developed to assist you in understanding the Hambro composite floor system, and for you to have at hand the information necessary for the most efficient and economical use of our Hambro products. Suggested detailing and design information throughout this manual illustrates methods of use.

  Manual, Design

Tablier métallique en diaphragme - Canam Bâtiments

diaphragme et son origine doivent être clairement indiquées sur les plans de conception de l’ingénieur responsable de la charpente du bâtiment. La disponibilité de ces informations assure que le coût, le choix du matériel et la méthode

  Diaphragme

Steelwork Design Guide to BS 5950-1: 2000

the case of reprographic reproduction only in accordance with the terms of the licences issued by the UK ... • Universal beams, Universal columns, joists, bearing piles, parallel flange channels, and structural tees cut from Universal beams and Universal columns to BS 4-1

  Parallel, Flange, Channel, Accordance, In accordance, Parallel flange channels

Steel Building Design: Design Data - Steel Construction

Licensing Agency, or in accordance with the terms of licences issued by the appropriate Reproduction Rights ... 2.3.3 Parallel flange channels A-3 3 SECTION PROPERTIES A-3 3.1 General A-3 3.2 Sections other than hollow sections A-3 3.2.1 Second moment of area (I) A-3 3.2.2 Radius of gyration (i) A-4 ...

  Parallel, Flange, Channel, Accordance, In accordance, Parallel flange channels

IS 1852 (1985): Rolling and cutting tolerances for hot ...

4.2.2 Width of Flange - The tolerance on flange width up to and includ- ing 100 mm shall he f 2 mm. 4.2.3 Flanqes Out-of-Square or Out-of-Parallel - The flanges shall be parallel with‘in 1 in 60 tolerances ( see Fig. 4 ). Fm. 4 FLANGES QUT-OF-SQUARE OR OUT-OF-PARALLEL

  Parallel, Flange

IS 811 (1987): Cold Formed Light Gauge Structural Steel ...

2.1 Y-Y Axis - A line parallel to the axis of web of section ( in the case of channels) or parallel to the webs (in the case of hat sections and rectangular sections) or parallel to either flange (in the case of angles and square sections), and passing through the centre of gravity of the profile

  Parallel, Flange, Channel

Seventh Edition Hot Rolled and Structural Steel Products

Taper Flange Beams 125 TFB, 100 TFB l Parallel Flange Channels 380 PFC, 300 PFC l l l l l l l 250 PFC l l l l l l l 230 PFC, 200 PFC, 180 PFC, 150 PFC l l l l l l l 125 PFC, 100 PFC, 75 PFC l Universal Bearing Piles 310 UBP 149, 110† 310 UBP 78.8 l l l l l l l 200 UBP 122 l Equal Angles 200 EA, 150 EA, 125 EA l l l l l 100 EA, 90 EA, 75 EA l

  Parallel, Flange, Channel, Parallel flange channels

HANDBOOK OF HANDBOOK OF STRUCTURAL STEELWORK

Parallel flange channels 166 ASB (Asymmetric Beams) 168 Equal angles 171 Unequal angles 172 Equal angles back-to-back 174 Unequal angles back-to-back 175 Tees cut from universal beams 176 Tees cut from universal columns 180 Hot-finished circular hollow sections 182 Hot finished square hollow sections 186 Hot-finished rectangular hollow sections 190

  Parallel, Flange, Channel, Parallel flange channels

HANGERS AND SUPPORTS FOR

in accordance with Section 15250, Mechanical Insulation. J. Provide hangers on piping on each side of, and within 6 inches of, hubless pipe couplings so the couplings will bear no weight. K. Provide supports that allow free axial movement and only support the weight of …

  Support, Accordance, Hanger, In accordance, Hangers and supports for