PDF4PRO ⚡AMP

Modern search engine that looking for books and documents around the web

Example: air traffic controller

KWIK BOLT 1 (KB1) PREMIUM EXPANSION ANCHOR

hilti , Inc. 1-800-879-8000 | en espa ol (Canada) Corporation BOLT 1 (KB1) PREMIUM EXPANSION ANCHORKB1 concrete and masonry technical supplement2 December 2020 Uncracked concreteCracked concreteGrout-filledconcretemasonrySeism ic Design Categories A-FFire sprinklerlistingsProfis Engineeringdesign softwareHollow Drill Bitand AdaptiveTorque Tool (AT )PRODUCT DESCRIPTIONF eatures and Benefits Instructions For Use (IFU) provides multiple installation methods including hilti Hollow Drill bit, or no hole cleaning with hammer drill and hilti Dust Removal System (DRS) for virtually dustless installation (OSHA Table 1 compliant). Accurate SafeSet installation when using the hilti SIW-6AT-A22 impact wrench and the SI-AT-A22 Adaptive Torque Module. Product and length identification marks facilitate quality control after installation. Maximized thread lengths and multiple embedment depths to accommodate various base plate thicknesses. Functional coatings and profiled EXPANSION wedges provide increased reliability.

2 Hilti KB1 anchors are to be considered ductile steel elements, with the exception of the 3/4x12 KB1 which is a brittle steel element. 3 Tensile фN sa = ф A se,N f uta as noted in ACI 318 Ch. 17. 4 Shear values determined by static shear tests with фV sa < ф 0.60 A se,V f uta as noted in ACI 318 Ch. 17.

Fullscreen Download

Tags:

  Steel, Brittle, Hilti, Brittle steel

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Spam in document Broken preview Other abuse

Transcription of KWIK BOLT 1 (KB1) PREMIUM EXPANSION ANCHOR

Documents from same domain

KB-TZ2 TECHNICAL GUIDE

www.hilti.com

KB-TZ2 Technical uide April 2021 5 Table 4 - Allowable Hilti carbon steel KB-TZ2 strength in uncracked concrete for hammer drill and core drill installations 1,2,3,4 Nominal anchor

  Hilti

Page 1/8 Safety Data Sheet acc. to ISO 11014 - Hilti USA

www.hilti.com

Page 2/8 Safety Data Sheet acc. to ISO 11014 Printing date 05/19/2015 Version number 5 Reviewed on 05/19/2015 (Contd. of page 1) 40.2.7 H319 Causes serious eye irritation.

  Sheet, Data, Safety, Pages, Page 1, Hilti, 8 safety data sheet acc

Hilti. Outperform. Outlast.

www.hilti.com

Selector Guide Through-Penetration Joint Reference Data Firestop Mortar (CP 637) Product description ... Concrete and masonry assemblies Expansion on setting (approx.)Walls and floors rated up to 4 hours ... Mix ratio (recommended, mortar to water):

  Guide, Concrete, Selector, Selector guide

ICC-ES Evaluation Report ESR-2269 - Hilti

www.hilti.com

1.0 EVALUATION SCOPE Compliance with the following codes: 2018, 2015, and 2012 International Building Code ® (IBC) 2018, 2015, and 2012 International Residential Code® (IRC) For evaluation for compliance with codes adopted by the Los Angeles Department of Building and Safety (LADBS), see ESR-2269 LABC and LARC Supplement.

  Report, Evaluation, Hilti, 2269, Icc es evaluation report esr 2269

HILTI TECHNICAL BULLETIN

www.hilti.com

Mar 04, 2018 · )n ≤ 1, where n=5/3 for 3/8- and 1/2-inch diameters (No. 3 and No. 4 rebar) and n=1 for 5/8 and 3/4-inch diameter or No. 5 and No. 6 rebar. 9 The critical spacing, s cr, is the smallest anchor spacing where full load values may be used. The minimum spacing, s min, is the minimum anchor spacing for which values are

  Hilti

HIT-RE 500 V3 - Hilti

www.hilti.com

Safety information for 2-Component-products 18/06/2020 US-OSHA - en 2/27 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If skin irritation or rash occurs: Get medical advice/attention. If eye irritation persists: Get medical advice/attention.

  Medical, Safety, Hilti, Hit re 500 v3

Hilti HIT-HY 200 with HIT-V

www.hilti.com

Anchor rods HIT-V GR / -HCR) are available in variable length MIO M12 TE 16 M16 M20 M24 TE 40 M27 - TE 70 M30 compressed air gun or blow out pump, set of cleaning brushes, dispenser Drill hole to the required embedment depth with an appropriately sized Hilti TE-CD Or TE-YD hollow drill bit with Hilti vacuum attachment. This drilling

  With, Anchor, Rods, Hilti, Anchor rods, Hilti hit hy 200 with hit

Hilti HIT-HY 200 with rebar

www.hilti.com

Hilti HIT-HY 200 with rebar Benefits - suitable for cracked and non- cracked concrete C 20/25 to C 50/60. - Approved automatic cleaning with the use of the hollow drill-bit high loading capacity, excellent handling HY 200-R version with extended curing time for rebar applications small edge distance and anchor spacing possible

  Rebar, Hilti

OPENINGS IN COMPOSITE FLOOR DECKS - Hilti

www.hilti.com

in-situ reinforced concrete topping. The decking not only acts as a permanent formwork to the concrete, but also provides sufficient shear bond with the concrete so that, when the concrete has cured, the two materials act together compositely to resist the loads on the deck. Openings in floor decks are a common part of any building.

  Concrete, Reinforced, Hilti, Reinforced concrete

HIT-1 ADHESIVE ANCHORING SYSTEM - Hilti

www.hilti.com

HIT-1 ADHESIVE ANCHORING SYSTEM Technical Supplement PRODUCT DESCRIPTION Hilti HIT-1 is a hybrid adhesive mortar combining resin, hardener, cement, and water. It’s formulated for fast curing and easy installation in a wide range of concrete and masonry base materials with temperatures ranging from 32°F (0°C) up to 95°F (35°C).

  Rinses, Adhesive, Cement, Hilti

Related documents

ENGINEERING ETHICS: THREE CASE STUDIES

www.ewh.ieee.org

• Other steel shapes and plate (1020 carbon steel, ASTM A7-24) Ftu58.2 ksi, Fty31.7 ... • 1920’sera brittle fracture provisions for steels for buildings and bridges commonly ... induced --failure in brittle materials at low temperatures.

  Plate, Failure, Steel, Carbon, Brittle, Carbon steel

How to properly specify weld studs for steelwise use with ...

www.aisc.org

tween steel and concrete are written with the intent to mitigate these risks by guiding the design in such a way that if a composite system does fail, it will be a ductile failure and not a brittle failure. The ultimate failure of a ductile connection, such as an embed plate with headed studs, will be preceded by yielding of the stud material ...

  Plate, Failure, Steel, Brittle, Brittle failure

SPECIFICATIONS - DEL METALS

www.delmetals.com

Type Q - Quenched and Tempered Low Alloy Steel Plate. Steels of this type display a very high yield strength and good resistance to brittle fracture and are especially suited for bridges and similar structures. While these steels may be readily welded, the welding and fabrication techniques are of ... cause of bend failure, in no case should ...

  Plate, Failure, Steel, Brittle, Steel plate

General Engineering Principles I.

www.nrc.gov

• Hard materials exhibit brittle, catastrophic failure. Therefore, for very hard materials, there ... Excessive presence of sulfur in steel makes it brittle in elevated temperatures. • When the phosphorus contents are too high in ... • Plate - is a rolled product more than 3 0 mmis a rolled product more than 3.0 mm ...

  Plate, Failure, Steel, Brittle

Fastener Design Manual - NASA

ntrs.nasa.gov

Carbon steel is the cheapest and most common bolt material. Most hardware stores sell carbon steel bolts, which are usually zinc plated to resist corrosion. The typical ultimate strength of this bolt material is 55 ksi. An alloy steel is a high-strength carbon steel that can be heat treated up to 300 ksi. However, it is not corrosion resistant

  Fastener, Steel, Carbon, Carbon steel

Weld Design and Specification - udel.edu

udel.edu

ICriteria for failure: ... • Brittle: Shear Strength ~ 0.75 Tensile Strength IWeld strength analysis is generally based on Shear Strength. 4 Static Strength of Welds ... 0.707w * h Butt Fillet h = throat size! Weld Size vs. Throat Size 1/8 75o 3/8 h = plate thickness = weld size Butt h = 0.707 * plate thickness 0.707 * weld size 1/4 Fillet. 5 ...

  Design, Specification, Plate, Failure, Brittle, Weld, Weld design and specification

Weld Design and Specification

udel.edu

ICriteria for failure: ... • Brittle: Shear Strength ~ 0.75 Tensile Strength IWeld strength analysis is generally based on Shear Strength. 4 Static Strength of Welds ... 0.707w * h Butt Fillet h = throat size! Weld Size vs. Throat Size 1/8 75o 3/8 h = plate thickness = weld size Butt h = 0.707 * plate thickness 0.707 * weld size 1/4 Fillet. 5 ...

  Plate, Failure, Brittle

Bolt Grades

www.healey6.com

use them. Well, first you need to understand what the term “ brittle ” really means. Brittleness in bolts is defined as failure at stresses apparently below the strength of the bolt material with little or no evidence of plastic deformation. Typically, fasteners are not brittle below 180 ksi ultimate tensile strength. Grade 5’s

  Failure, Brittle

Advanced Composite Material for Aerospace Application-a …

ripublication.com

solution. These materials, while strong, were also brittle. Because of this, when they failed, they did so terribly. The theoretical high strengths could be severely undermined by flaws in the material, such as a micro crack on the surface. Also, the stress-to-failure varied widely between what should have been identical components,

  Failure, Brittle

Related search queries

Steel, Plate, Carbon steel, Brittle, Failure, Brittle failure, Steel Plate, Fastener, Weld Design and Specification