PDF4PRO ⚡AMP

Modern search engine that looking for books and documents around the web

Example: tourism industry

Lab 3.5.1: Basic VLAN Configuration - ut

All contents are Copyright 1992 2007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 1 of 6 Lab : Basic VLAN Configuration Topology Diagram Addressing Table Device (Hostname) Interface IP Address Subnet Mask Default Gateway S1 VLAN 99 N/A S2 VLAN 99 N/A S3 VLAN 99 N/A PC1 NIC PC2 NIC PC3 NIC PC4 NIC PC5 NIC PC6 NIC Initial Port Assignments (Switches 2 and 3) Ports Assignment Network Fa0/1 0/5 Trunks (Native VLAN 99) /24 Fa0/6 0/10 VLAN 30 Guest (Default)

If necessary, refer to Lab 2.5.1, Appendix 1, for the procedure to clear switch configurations. It is a good practice to disable any unused ports on the switches by putting them in …

Fullscreen Download
Loading..

Tags:

  Configuration, Basics

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Spam in document Broken preview Other abuse

Transcription of Lab 3.5.1: Basic VLAN Configuration - ut

Documents from same domain

Lab 2.5.1: Basic Switch Configuration

courses.cs.ut.ee

Set the login password to cisco . Also configure the vty lines 0 to 15 with the password cisco . S1#configure terminal Enter the configuration commands, one for each line. When you are finished, return to global configuration mode by entering the exit command or pressing Ctrl-Z. S1(config)# line console 0 S1(config-line)# password cisco

  Configuration, Cisco

Lab 4.4.1: Basic VTP Configuration - Arvutiteaduse instituut

courses.cs.ut.ee

Set the VTP domain name to Lab4 and the VTP password to cisco on all three switches . Configure S1 in server mode, S2 in client mode, and S3 in transparent mode.

  Cisco

Lab: Basic OSPF Configuration Lab

courses.cs.ut.ee

The OSPF router ID is used to uniquely identify the router in the OSPF routing domain. A router ID is an IP address. Cisco routers derive the Router ID in one of three ways and with the following precedence: 1. IP address configured with the OSPF router-id command. 2. Highest IP address of any of the router’s loopback addresses. 3.

  Cisco, Routing

Lab 5.5.1: Basic Spanning Tree Protocol - ut

courses.cs.ut.ee

CCNA Exploration LAN Switching and Wireless: STP Lab 5.5.1: Basic Spanning Tree Protocol ... • Configure a password of cisco for console connections. • Configure a password of cisco for vty connections. (Output for S1 shown) Switch> enable Switch# configure terminal

  Basics, Cisco, Ccna, Protocol, Tree, Spanning, Basic spanning tree protocol

Lab: Basic Router Configuration

courses.cs.ut.ee

R1(config-if)#interface serial 0/0/0 R1(config-if)#ip address 192.168.2.1 255.255.255.0 R1(config-if)#clock rate 64000 R1(config-if)#no shutdown R1(config-if)# Note: The interface will be activated until the serial interface on R2 is configured and activated Step 12: Return to privileged EXEC mode. Use the end command to return to privileged ...

  Configuration, Basics, Routers, Config, Basic router configuration

Lab: Basic Static Route Configuration

courses.cs.ut.ee

If you can answer yes to all the proceeding questions, the interface should come up. CCNA Exploration Routing Protocols and Concepts: Static Routing Lab …

  Configuration, Question, Basics, Ccna, Route, Static, Basic static route configuration

Packet Tracer Configuring VPNs (Optional) - ut

courses.cs.ut.ee

Packet Tracer – Configuring VPNs (Optional) © 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 2 of 6 ISAKMP Phase 1 ...

  Packet, Optional, Configuring, Carter, Vpns, Packet tracer configuring vpns

Rui Jiang Xuegong Zhang Michael Q. Zhang Editors Basics of ...

courses.cs.ut.ee

include useful introductions to concepts such as gene or Bayesian methods. This is a valuable aspect of the volume allowing a student various angles of approach to a new topic. Chapter 1, “Basics for Bioinformatics,” defines bioinformatics as “the storage, manipulation and interpretation of biological data especially data of nucleic acids

  Basics, Bayesian

Related documents

Cisco Catalyst 2960-S Series Switches Data Sheet

www.cisco.com

The Cisco® Catalyst® 2960-S Series Switches are fixed-configuration Gigabit Ethernet switches (Figure 1) ... with settings optimized for the device type. Cisco Smart Troubleshooting is an extensive array of diagnostic commands and system health checks ... Cisco Catalyst 2960S-48TD-L 1.75 x 17.5 x 11.8 4.5 x 44.5 x 30

  Devices, Configuration, Series, Cisco, Sheet, Data, Switches, Catalysts, 174 catalysts, 9206, Cisco catalyst 2960 s series switches data sheet, 174 2960 s series switches

Cisco Expressway-E and Expressway-C - Basic Configuration

www.cisco.com

Expressway configuration details used in this document are listed in Appendix 1: Configuration Details, page 51. DNS records required for the example deployment used in this document are in Appendix 2: DNS Records, page 55. Details of required NAT and firewall configurations are in Appendix 3: Firewall and NAT Settings, page 57.

  Configuration, Basics, Cisco, Basic configuration

Related search queries

Cisco Catalyst 2960-S Series Switches Data Sheet, Cisco® Catalyst® 2960-S Series Switches, Configuration, Device, Cisco, Basic Configuration