LM5164 100-V Input, 1-A synchronous buck DC/DC converter ...
LM5164 100-V Input, 1-A synchronous buck DC/DC converter with ultra-low IQ 1 1 Features 1• Designed for reliable and rugged applications – Wide input voltage range of 6 V to 100 V – Junction temperature range: –40°C to +150°C – Fixed 3-ms internal soft-start timer – Peak and valley current-limit protection
Tags:
Converter, Current, Dc converter
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
LM136-2.5,LM236-2.5,LM336-2 - TI.com
www.ti.comLM136-2.5/LM236-2.5/LM336-2.5V Reference Diode General Description The LM136-2.5/LM236-2.5 and LM336-2.5 integrated cir-cuits are …
SimpleLink™ CC3120, CC3220 Wi-Fi ... - Texas …
www.ti.comUser User x x x x x x x x x x x x x x x x x x x x Application Servers Vendor IoT Devices Internet Introduction www.ti.com 4 SWRA509A–February 2017–Revised March 2017 Submit Documentation Feedback
www.ti.com SNVS749F - Texas Instruments
www.ti.comLM136-2.5-N SNVS749F – MAY 1998– REVISED APRIL 2013 www.ti.com Typical Performance Characteristics (continued) Temperature Drift Figure 13. …
MSP430x2xx Family User's Guide (Rev. J) - TI.com
www.ti.comMSP430x2xx Family User's Guide Literature Number: SLAU144J December 2004– Revised July 2013
Guide, User, Family, Msp430x2xx family user s guide, Msp430x2xx
1.8-V Micropower CMOS Operational Amplifier …
www.ti.com5 OPA2333-HT www.ti.com SBOS483I –JULY 2009–REVISED MAY 2015 Product Folder Links: OPA2333-HT Copyright © 2009–2015, Texas Instruments Incorporated Submit Documentation Feedback
Operational, Texas, Texas instruments, Instruments, Cmos, Amplifier, Micropower, Micropower cmos operational amplifier
LMC6482 CMOS Dual Rail-To-Rail Input and Output ...
www.ti.comLMC6482 www.ti.com SNOS674E –NOVEMBER 1997–REVISED APRIL 2015 5 Pin Configuration and Functions D, DGK and P Packages 8-Pin SOIC, VSSOP and PDIP (Top View) Pin Functions PIN TYPE DESCRIPTION NO.
OPAx354 250-MHz, Rail-to-Rail I/O, CMOS …
www.ti.comOPA354 IN +IN V OUT V+ V Product Folder Order Now Technical Documents Tools & Software Support & Community Reference Design An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use …
Analog linearization of resistance temperature …
www.ti.com21 Analog Applications Journal Texas Instruments Incorporated 4Q 2011 www.ti.com/aaj High-Performance Analog Products …
Resistance, Temperatures, Texas, Texas instruments, Instruments, Analog, Analog linearization of resistance temperature, Linearization
TMS320C28x DSP/BIOS 5.x Application …
www.ti.comSPRU625L—August 2012 API Functional Overview 9 Submit Documentation Feedback www.ti.com Naming Conventions 1.2 Naming Conventions The format for a DSP/BIOS operation name is a 3- or 4-letter prefix for the module that contains the
WL18x7MOD WiLink™ 8 Dual-Band Industrial …
www.ti.comProduct Folder Order Now Technical Documents Tools & Software Support & Community Reference Design An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
Related documents
AN149 Modeling and Loop Compensation Design of …
www.analog.comSince the current and voltage sources are the products of two variables, the system is still a nonlinear system. SmAll SIgnAl modelIng of PWm ConVerter PoWer StAge A switching mode power supply (SMPS), such as the buck step-down converter in Figure 4, usually has two operating modes, depending on the on/off state of its main control switch.
Snubber Circuits Suppress Voltage Transient Spikes in ...
pdfserv.maximintegrated.comloop due to (dv/dt) induced spurious turn-on of the MOSFET as a result of the transient voltage spike. Secondary Leakage Inductance and the Rectifier Diode The transformer secondary leakage inductance may couple with the reverse recovery current IREC of the output rectifier diode to cause ringing when the diode turns off.
High-voltage resonant controller
www.st.comThe IC enables the designer to set the operating frequency range of the converter by means of an externally programmable oscillator. At start-up, to prevent uncontrolled inrush current, the switching frequency starts from a programmable maximum value and progressively decays until it reaches the steady-state value determined by the control loop.
Zero Voltage Switching Resonant Power Conversion
www.ti.comvalue L, and the magnetizing current ML., as well as the inductor’s DC resistance is negligi-ble. In addition, both the input voltage VjN and output voltage V. are purely DC, and do not vary during a given conversion cycle. Last, the converter is operating in a closed loop configu-ration which regulates the output voltage V. .
Switching, Loops, Power, Converter, Current, Conversion, Zero, Voltage, Resonant, Zero voltage switching resonant power conversion
TDA8954 2 × 210 W class-D power amplifier - NXP
www.nxp.compop noise-free start-up. The bias-current setting of the (VI converter) input stages is related to the voltage on the MODE pin. In Mute mode, the bias-current setting of the VI converters is zero (VI converters are disabled). In Operating mode, the bias current is …
Building a DC-DC Step-Down (Buck) Converter Circuit Using ...
www.egr.msu.eduThe primary objective is to build a simple circuit of DC-DC stepping-down (Buck) converter. With the LM7809 positive voltage regulator, it is expected to have about 11V-17V DC input stepping-down to 9V DC output. And the secondary objective is to be able to achieve output voltage that is stabilized at its level.