Car buyers guide - fairtrading.nsw.gov.au

Page 1 of 24 Car buyers guide Introduction Buying a new car can be an overwhelming experience with so many considerations . This booklet is designed to assist consumers through the entire car buying and owning experience – what type

  Guide, Buyers, Car buyers guide

New tenant checklistFor any promises made by the landlord ...

At the start of every tenancy, your landlord or agent should give you: a copy of this information (the New tenant checklist) a copy of your lease (tenancy agreement) 2 copies of the premises condition report (more on that later) an invitation to lodge the bond using Rental Bonds Online (RBO). Or, if you are unable to use RBO, a

GAS SUPPLY Licensee’s Copy Licensee’s Certificate of ...

Quantity connected Brand : Serial Number . Water Capacity : 0 Stationary engine power or air conditioner 1 Cook top or wok cooker 2 . Refrigeration or Absorption chiller

  Serial, Engine

Consumer Building Guide - fairtrading.nsw.gov.au

Builders and tradespeople must give you a copy of this guide before entering into a contract for residential building work that costs more than $5,000.

Condition Report - NSW Fair Trading | NSW Fair Trading

condition report is an important record of the condition of the residential premises when the tenancy begins and may be used as evidence of the state of repair or general condition of the premises at the commencement of the tenancy. It is important to complete the condition report accurately. It may be vital if there

  Report, Conditions, Condition report

Tenancy Condition Report - NSW Fair Trading

condition report accurately. It may be vital if there is a dispute, particularly about the return of the rental bond money and any damage to the premises. 2. At the end of the tenancy the premises will be inspected and the condition of the premises at that time will be compared to that stated in the original condition report. 3.

  Report, Conditions, Condition report

Code of conduct for the short-term rental accommodation ...

ensuring residential neighbours can enjoy the amenity of their homes without unreasonable disturbance. This code of conduct responds to this need by establishing behavioural obligations for short-term rental accommodation participants. In recent years, there has been an increasing focus on the regulation of the short-term rental

  Code, Residential, Conduct, Code of conduct

Notice to terminate Tenancy Agreement - tenant

the notice is given (section 96) Termination of periodic tenancy: 21 days notice (section 97) Breach of agreement: 14 days notice (section 98) (NB: the notice may specify a date that is before the end of the fixed term of the agreement).

  Agreement, Notice, Tenancy, Terminate, Notice to terminate tenancy agreement

Notice To Terminate Tenancy Agreement - NSW Fair Trading

Notice To Terminate Tenancy Agreement ... End of fixed term tenancy: 30 days minimum notice required (Section 84) Termination of periodic tenancy without a reason: 90 days notice (Section 85) (NB: if tenant is COVID-19 impacted and …

  Notice, Tenancy, Terminate, Notice to terminate tenancy

Deck and balcony safety - NSW Fair Trading

Different timbers need different treatment and maintenance and may be more or less durable when used in exposed external environments. Be certain about what type of timber was used in the construction of your deck or balcony. Make sure your maintenance routine is the right

  Timber

Guide to Standards and Tolerances (currently under review)

The Guide to Standards and Tolerances (the Guide) has been developed for use by builders and building owners as a convenient reference for acceptable standards of workmanship in domestic building construction. It is intended to address areas

  Standards, Tolerance, Standards and tolerances

Specifications and Tolerances for Reference Standards and ...

tolerances useful. Use of these standards at all appropriate levels of manufacture, distribution, and Weights and Measures inspection will help promote accuracy and uniformity in commerce. The terms “weight”, “mass standard”, and “mass” as used in this publication refer to all sizes in

  Standards, Specification, Tolerance, Specifications and tolerances for

ACI 117-10 Specification for Tolerances for Concrete ...

Specification synopsis: This specification provides standard tolerances for concrete construction and materials. This document is intended to be used by specification writers and ACI committees writing standards as the reference document for establishing tolerances for concrete construction and materials.

  Standards, Tolerance

IS 4251 (1967): Quality tolerances for water for processed ...

QUALITY TOLERANCES FOR WATER FOR PROCESSED FOOD INDUSTRY o. FOREWO RD 0.1 This Indian Standard was adopted by the Indian Standards Institution on 7 Aug~t 1967, after the draft finalized by the Water Sectional Committee had been approved by the Chemical Division Council. 0.2 In processed food industry, water is used for a number of purposes,

  Standards, Tolerance

General tolerances for Iinearand angular DIN dimensions ...

General tolerances based on the tolerancing principle specified in ISO 8015 are only to be applied when the drawing concerned contains the reference 'Tolerancing to ISO 8015'. Where that is the case. the general geometrical tolerances (i.e. the tolerances of form and position) apply independently of the actual local sizes of the workpiece feature.

  Tolerance

2015 Standard for Performance Rating of Water-chilling and ...

91 Section H4 The table reference for operating condition tolerances must be changed to Table 12 instead of Table 11. This was a typo that must be corrected. Current sentence: Tolerances and stability requirements are defined in Table 11 in Section 5.6.2. New sentence: Tolerances and stability requirements are defined in Table 12 in Section 5.6.2.

  Tolerance

General tolerances - 21food.cn

The use of general tolerances for size and geometry simplifies the task of ensuring that this prerequisite is met. 1 Scope This part of ISO 2768 is intended to simplify drawing indications and specifies general geometrical tolerances to control those features on the drawing which have no respective individual indication.

  Tolerance