2015 National Design Specification - AWC

NDS-1991 with an approval date of October 16, 1992. In 2010, AWC was separately incorporated, re-chartered, and accredited by ANSI as a standards developing organization. The current edition of the Standard is designated ANSI/AWC NDS-2015 with an approval date of September 30, 2014. In developing the provisions of this Specification,

  Design, Specification, 2015, National, October, 2015 national design specification

Prescriptive Residential Wood Deck Construction Guide

3. Maximum allowable overhang cannot exceed L/4 or ¼ of actual main span. Assumes cantilever length/180 deflection with 220 lb point load (See Figure 1A and Figure 2). 4. Incising assumed for Douglas Fir-Larch, Hem-Fir, and Spruce-Pine-Fir. 5. Design values based on northern species with no incising assumed. 6. Ledger shall be a minimum of 2x8 ...

  Guide, Construction, Deck, Maximum, Minimum, Deck construction guide

Design Aid 6 Beam Design Formulas with Shear and Moment ...

AMERICAN WOOD COUNCIL w R V V 2 2 Shear M max Moment x 7-36 A ab c x R 1 R 2 V 1 V 2 Shear a + — R 1 w M max Moment wb 7-36 B Figure 1 Simple Beam–Uniformly Distributed Load

  Moment

WIND & SEISMIC - AWC

2.1.2.1 Allowable Stress Design: Allowable stress design (ASD) shall be in accordance with the Na-tional Design Specification ® (NDS ®) for Wood Con-struction (ANSI/AF&PA NDS-05) and provisions of this document. 2.1.2.2 Strength Design: Load and resistance factor design (LRFD) of wood structures shall be in accor-

  Design, Seismic, Load, Wind, Wind amp seismic

INTERIOR SHEAR WALLS - awc.org

interior shear walls to be designed to resist wind loads. WFCM Section 2.4.4.2 states: “Walls parallel to the applicable wind load or seismic motion shall provide the required shear resistance at each level. The sum of the individual shearwall segment shear

  Walls, Interior

2012 ASD/LRFD Manual for Engineered Wood Construction

ASD/LRFD MANUAL FOR ENGINEERED WOOD CONSTRUCTION iii AMERICAN WOOD COUNCIL FOREWORD This Allowable Stress Design/Load and Resistance Factor Design Manual for Engineered Wood Construction (ASD/LRFD Manual) provides guidance for design of most wood-based structural products used in the construction

  Construction, Woods, Engineered, Engineered wood construction

2015 National Design Specification Supplement - awc.org

AMERICAN WD CUNCIL. DESIGN VALUES FOR WOOD CONSTRUCTION – NDS SUPPLEMENT iii. Introduction. This Supplement is a compendium of reference de …

  Supplement

2005 Span Tables For Joists And Rafters - awc.org

2 EXPLANATION OF TABLES AMERICAN WOOD COUNCIL 7. LUMBER IDENTIFICATION The tabulated spans in these tables apply to lum-ber identified by the grade stamp of, or certificate of

  Table

WCD1 - Details for Conventional Wood Frame Construction

may provide equal, or possibly, improved performance. These, however, must provide performance assurance ac-ceptable to the owner and the building inspector. Dimensioning. In general, dimensions for framing lumber, wood sid-ing and trim referenced in this document are nominal dimensions; i.e., 2x4, 2x6, etc., for simplicity. Actual sur-

  Performance, Details

MAT100: The Basics of Wood Frame Construction

one comprehensive program for building officials on wood frame construction basics. In each module, learning outcomes will be further refined respectively. MAT 100 learning outcomes (see slide). 5 MAT100: Learning Outcomes 3. Floor, roof/ceiling, wall framing 4. Wall bracing, introduction to Wood Frame Construction Manual 5. Fireblocking ...

  Frame, Slides

Bearings - NMB Technologies

*Stainless steel is the standard material Bearing Types. NMBTC.COM / 818.341.3355 Introduction 7 ... Z Metallic Shield (Fitted with Snap-Ring) H Metallic Shield (Pressed) K Metallic Shield (Staked) ... Other materials are also available for the plastic retainer. 9. NMBTC.COM / …

  Other, Material, Steel, Stainless, Stainless steel, Metallic, Other materials

Installing, modifying and maintaining domestic plumbing ...

Particular materials unsuitable for use in contact with water intended for ... Pipes of different metallic materials are not to be connected unless suitable precautions are taken to ensure that corrosion through galvanic action cannot take place. Water fittings should be adequate for the ... STAINLESS STEEL PIPES: BS 4127: Light gauge stainless ...

  Material, Steel, Contact, Stainless, Stainless steel, Metallic, Metallic materials, In contact

Biomaterials- Chapter One

medical practice, polymeric materials alone and in combination with metals and ceramics are becoming increasingly incorporated into devices used in the body. 2- Metals The metallic systems most frequently used in the body are: (a) Iron-base alloys of the 316L stainless steel (b) Titanium and titanium-base alloys, such as

  Material, Steel, Stainless, Stainless steel, Metallic

Clean Steam Systems in the Pharmaceutical Industry

corrosive to many materials commonly used in utility steam systems. Carbon steel, gunmetal and bronze, all commonly found in utility steam components, would all be rapidly corroded. Metal components for clean steam systems are therefore usually AISI 316L stainless steel, or sometimes titanium. Non-metallic materials used include EPDM and PTFE.

  Material, Steel, Steam, Stainless, Stainless steel, Metallic, Metallic materials

Standard Test Methods for Tension Testing of Metallic ...

1.1 These test methods cover the tension testing of metallic materials in any form at room temperature, specifically, the methods of determination of yield strength, yield point elongation, tensile strength, elongation, and reduction of area. 1.2 The gauge lengths for most round specimens are re-quired to be 4D for E8 and 5D for E8M.

  Material, Metallic, Metallic materials

B-Line series product line overview - Eaton

Spring steel fastener anchors. Pipe hangers Traditional strut systems. Pipe hangers. Manufactured from carbon or stainless steel and available in a variety of finishes, our pipe hangers and supports are suited for everything from indoor commercial to highly corrosive industrial applications. All of these products meet or exceed the MSS or Federal

  Eaton, Steel, Stainless, Stainless steel

Cerabar M PMC51, PMP51, PMP55 (Technische Information)

metallic sensors Application The device is used for the following measuring tasks: • Absolute pressure and gauge pressure measur ement in gases, steams or liquids in all areas of process engineering and process measurement technology • Level, volume or mass measurements in liquids • High process temperature

  Metallic

Cerabar M PMC51, PMP51, PMP55

Cerabar M PMC51, PMP51, PMP55 8 Endress+Hauser Turn down calculation LRL LRV URV URL 1 = 2 3 A0029545 1 Calibrated/adjusted span 2 Zero point-based span