(1.27 mm) .050 FTS SERIES MICRO LOW-PROFILE …

(1.27 mm) .050" FTS SERIES FTS1102L FTS11002FV FTS12201FV FTS11102LVSA Mates with socket strips or IDC cable Impedance matched for high-speed applications

  Series, Profile

HIGH MATING CYCLES LOW-PROFILE DUAL WIPE SOCKET

(1.27 mm) .050" CLP SERIES T Cw contacts CLP–107–02–F–D–P CLP–130–02–L–D CLP–116–02–F–DH CLP–115–02–L–D S m Lw-pro˜le

REVISION CF SSW-1XX-XX-XXX-X-XX-XXX-XX

this document contains confidential and proprietary information and all design, manufacturing, reproduction, use, patent rights and sales rights are expressly reserved by …

  Xx xxx x xx xxx xx

HIGH MATING FTSH–125–01L–DVEJ CYCLES SMT …

(1.27 mm) .050" FTSH–125–01L–DVEJ FTSH–120–01F–DV FTSH110–01–L–DV m . A Sm . Cm m m Sm Sm m . WWW.SAMTEC.COM For complete specifications and

POWER AND VOLTAGE RATING - Samtec …

VOLTAGE and POWER Ratings final 101207.doc 1 OF 13 10/18/2007 D-SCOPE-TECH, INC. POWER AND VOLTAGE RATING SCOPE: The purpose of this document is to take the confusion out of power and voltage ratings in

  Power, Ratings, Voltage, Power and voltage rating, Power ratings

REVISION AO FFSD-XX-X-XX.XX-01-X-X-XXX

this document contains confidential and proprietary information and all design, manufacturing, reproduction, use, patent rights and sales rights are expressly reserved by …

  Revisions, Ffsd xx x xx, Ffsd, Xx 01

SFM110–02–L–D–A SFML125–T2–LD–LC …

(1.27 mm) .050" SFML125–T2–LD–LC SFM–125–02–L–SH SFM110–02–L–D–A SFML115–T2–LD–LC Choice of SMT or through-hole tails Locking feature

  Sfm110 02 l d a sfml125 t2 ld lc, Sfm110, Sfml125

HIGH MATING CYCLES THROUGH-HOLE MICRO …

(1.27 mm) .050" FTSH SERIES Im m f applications ( CLP S) sock ips IC le T r surf m (2.51 mm) .0" O (1.27 mm) .050" m FTSH–120–02–L–D FTSH–120–01–L–D–RA

  Ftsh

REVISION J - Samtec Microelectronics

1.95049.53.05001.270.45011.43.0350.89 (typ) cl cl 01 all dimensions are symmetric about the centerline. notes: stencil to be .0060[.152] thick. a k j h

  Dimensions

HIGH MATING CYCLES HTSW115–05–LQ TSW–209–09F–SRA …

tsw, htsw series tsw–112–07–g–t tsw10910–f–d–ra htsw12013–t–d tsw–11416g–sre, , m . a sm . cm m m sm sm m .

CONA S - ARI Armaturen

• Socket weld ends ....3 ___ acc. to DIN EN 12760 • Butt weld ends ....4 _____ Weld preparation acc. to EN ISO 9692 identification No. 1.3 and 1.5 (Note restriction on operating pressure / inlet temperature depending to design!) Features • Ball float steam trap with level control for the condensate-discharge from

  Sockets, Weld, Socket weld

Underground Drainage Systems

weld joint or as 110mm mechanical or multiflex bends. ... spigot or socket/socket (shown) and can be adjusted from 0°-90°. Inspection chambers ... Start of external drain* 12 12 – 22 45 Rodding eye 22 22 22 45 45 Type 1 access fitting 150 x 100mm – – 12 22 22 Type 2 access fitting

  Sockets, Weld, 45 45

Bellows-Sealed Valves, B Series (MS-01-22;rev N;en-US;Catalog)

Tube socket weld ends—1/4 to 1/2 in. alloy 400 Tube butt weld ends—1/4 to 3/4 in. alloyFemale VCR® face seal fittings—1/4 and 1/2 in. Integral male VCR face seal fittings—1/4 and 1/2 in. Panel and bottom mounting Technical Data Determined …

  Sockets, Weld, Socket weld

Integrally Reinforced Forged Branch Outlet Fittings ...

requirements for 90 and 45 degree integrally reinforced forged branch outlet fittings of buttwelding, socket welding, and threaded types. 1.2 Fittings manufactured to this Standard Practice are designed to make a fully reinforced branch connection in accordance with applicable piping code requirements, when attached, at an opening in a run pipe by

  Sockets

Product Knowledge Guide Plastics

S Socket SPG Spigot 1/4 bend 90-degree bend 1/6 bend 60-degree bend 1/8 bend 45-degree bend 1/16 bend 22.5-degree bend. Products Offered 8 *Non-Pressure ... Solvent Weld Joints • Solvent cements must meet ASTM D 2564. • Primer is required. • …

  Sockets, Weld

C-18 Forged Steel valves

SW Socket Weld SWxNPT SW x NPT NPTxSW NPT x SW SH10 Schedule 10 SH40 Schedule 40 SH80 Schedule 80 SH160 Schedule 160 SHXXS Schedule XXS RF Raised Face - Smooth Finish 3.2-6.3 - Spiral RJ Ring Joint VALVE TY PE 0 Gate, IS&Y 1 Gate, OS&Y 2 Globe, IS&Y 3 Globe, OS&Y 4 Check, Piston 5 Check Ball 6 Check Swing TRI M DESIGN O BTURATOR …

  Sockets, Weld, Socket weld

VCR Metal Gasket Face Seal Fittings (MS-01-24;rev T;en-US ...

4 Weld, VCR, VCO, Pipe, and Vacuum Fittings WELD FITTINGS Ordering Information, Pressure Ratings, and Dimensions Dimensions are for reference only and are subject to change . The E dimension refers to the smallest nominal inside diameter of the part . To order fittings manufactured in accordance with Swagelok Ultrahigh-Purity Process Specification (SC-01) …

  Seal, Metal, Fitting, Faces, Gaskets, Weld, Swagelok, Metal gasket face seal fittings

CURE TIMES - Oatey

The pipe size, socket fit, ambient temperature, relative humidity, solvent cement used and the system operating pressure should all be considered when determining set up/cure times. Average Handling/Set Up Times for PVC/CPVC Solvent Cements Handling/Set Up Time is the time required prior to handling the joint. In damp or humid weather, allow

  Time, Sockets, Cures, Oatey, Cure times