PDF4PRO ⚡AMP

Modern search engine that looking for books and documents around the web

Example: air traffic controller

TIPS & TRICKS ON DOUBLE PULSE TESTING - Rohde & Schwarz

Application Note TIPS & TRICKS ON DOUBLE PULSE TESTING From designing a test setup to performing accurate measurements DOUBLE PULSE TEST Products: R&S RTO2000 R&S RTE1000 R&S RTA4000 R&S RTM3000 R&S HMF2550 Jens Schweickhardt, Kevin Hermanns (PE-Systems), Dr. Markus Herdin (R&S) | GFM347 | Version | Rohde & Schwarz | Application Note Tips & TRICKS on DOUBLE PULSE TESTING 2 Contents Abbreviations .. 3 List of Nomenclatures .. 4 1 Overview .. 6 2 DOUBLE PULSE Test .. 7 Test Procedure ..8 Measurement Parameters .. 11 Switching Times , , .. 11 Switching Energy , .. 11 Reverse Recovery Characteristics of Freewheeling Diode.

first pulse is significantly longer than the duration of the break, in which the switch is off, and then the duration of the second pulse, in which the current through the inductance rises again. The length of the pulse break must be chosen such that the switching process starting the pulse break has decayed before the second pulse.

Fullscreen Download

Tags:

  Pulse

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Spam in document Broken preview Other abuse

Transcription of TIPS & TRICKS ON DOUBLE PULSE TESTING - Rohde & Schwarz

Documents from same domain

EMC Standards - Rohde & Schwarz

scdn.rohde-schwarz.com

IEC 61000-4-2 - Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test IEC 61000-4-3 - Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test

  Compatibility, Standards, Testing, Part, Electromagnetic, Electromagnetic compatibility, Emc standards

IEEE 802.11 ax TECHNOLOGY INTRODUCTION

scdn.rohde-schwarz.com

IEEE 802.11 is the IEEE working group developing wireless local area network specifications. The group began work in the late 1990s and since then has created several ... 1.6 µs: targeting high efficiency in outdoor channels and indoor UL MU-MIMO/ OFDMA

  Outdoor

Related documents

Lead (Pb)-Bearing Thick Film, Rectangular Chip Resistors

www.vishay.com

Pulse Duration t i (s) 10-5 10-4 10-3 10-2 10-1 1 10 100 Maximum pulse load, single pulse; applicable if P 0 and n < 1000 and Û ≤ Û max.; for permissible resistance change equivalent to 8000 h operation 1000 10 1 0.1 0.01 10-6 Continuous Pulse Maximum pulse load, continuous pulses; applicable if P ≤ P (ϑ amb) and Û ≤ Û max.;

  Pulse, Load, Pulse load

G2RL - Omron

omronfs.omron.com

• Reduced power consumption with voltage holding and pulse ... High-capacity type (resistive load) High-sensitivity type (resistive load) Item Model 1-pole 2-pole 1-pole Contact type Single Contact material Ag-alloy (Cd free) Rated load 12 A at 250 VAC 12 A at 24 VDC (See note) 8 A at 250 VAC 8 A at 30 VDC (See note) 16 A at 250 VAC

  Pulse, Load

AN2686 Ethernet Compliance Testing for 10BASE-T, …

ww1.microchip.com

For link pulse testing with Twisted Pair Model, the DUT is connected to the DUT port for the 10BASE-T Parametric/Tem-plate Test with Twisted Pair Model, and the oscilloscope probe is attached to the test jumper after load selection. To configure the DUT for link pulse testing, refer to 10BASE-T Link Pulse Setting on any part for register settings.

  Testing, Compliance, Pulse, Load, Ethernet, Ethernet compliance testing

500 mA, Low Voltage, Low Quiescent LDO Regulator

ww1.microchip.com

Jan 02, 2008 · 4: Load regulation is measured at a constant junction temperature using low duty-cycle pulse testing. Load regulation is tested over a load range from 1 mA to the maximum specified output current. 5: Dropout voltage is defined as the input-to-output voltage differential at which the output voltage drops 2% below its nominal value that was ...

  Pulse, Load

Servo Motor Selection Flow Chart - Omron

www.ia.omron.com

Load Inertia Load Inertia ≤ Motor Rotor Inertia x Applicable Inertia Ratio Effective Torque Effective Torque < Motor Rated Torque †Please allow a margin of about 20%. * ... Check if the Pulse Frequency does not exceed the Maximum Response Frequency or Maximum Command Frequency of a Positioner.

  Pulse, Load

Datasheet - L78 - Positive voltage regulator ICs

www.st.com

Nov 23, 2010 · 1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. Note: Minimum load current for regulation is 5 mA. L78 Electrical characteristics DS0422 - Rev 36 page 6/55

  Pulse, Load

CHAPTER 2 SINGLE PHASE PULSE WIDTH MODULATED …

www.tntech.edu

which the voltage gain is improved, leading to an increased load fundamental voltage, reduction in total current distortion and increased load power factor. In Figure 2.5, the top devices are assigned to be S11 and S21 while the bottom devices as S12 and S22, the voltage equations for this converter are as given in the following equations. 23

  Pulse, Load

LTC6992-1 (Rev. D) - Analog Devices

www.analog.com

LTC6992-1/LTC6992-2/ LTC6992-3/LTC6992-4 4 e For more information www.analog.com The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. Test conditions are V+ = 2.25V to 5.5V, VMOD = 0V to VSET, DIVCODE = 0 to 15 (NDIV = 1 to 16,384), RSET = 50k to 800k, RLOAD = 5k, CLOAD = 5pF …

  Devices, Analog devices, Analog

Related search queries

PULSE, Pulse load, Load, Ethernet Compliance Testing, Analog Devices