Connectivity and Structured Cabling

(M) = Male Plug (F) = Female Socket RF Connectors & Adapters 5 Part No . Compatible Cable Crimper Stripper 28-91007 (CPMC782) Belden 1505A, 24-9959P 24-7732P

RF Cable Assembly Guide - Bel Fuse

4 Metric assemblies available, highlighted in blue MMCX Straight Plug to MMCX Straight Plug Connector by Cable Type: RG-178 (135-3402-001) RG-316 (135-3403-001) Part Number Standard Cable Lengthc Metric Cable Length Cable Type 415-0066-006 6" 152 mm RG-178

  Guide, Cable, Assembly, Assemblies, Rf cable assembly guide

The 0RQB-30Y05L is an isolated DC/DC converter providing ...

The 0RQB-30Y05L is an isolated DC/DC converter providing 30 W of output power from a wide input range (24 V, 48 V, 72 V, 96 V, 110 V typical). Standard features include remote on/off, input under-voltage

  Ranges, Input, Voltage, Wide, Wide input range

RoHS compliant Ultra-wide 3.5 to 16 volt input range Input ...

Ultra-wide input voltage range allows operation from battery power as well as system power. The output is electrically isolated, thereby allowing the output to be configured as a positive or negative output voltage. Fully-isolated and filtered outputs permit usage in sensitive and low noise circuits.

  Ranges, Input, Voltage, Wide, Wide input voltage range, Input range input

The Bel Power Solutions produces ... - Bel - Power | Protect

E, F OVP-24G DUAL OUTPUT AA, B, BB, CC OVP-12G protects both outputs E OVP-24G protects both outputs TRIPLE OUTPUT AA, BAA, D CBB, 131 DBB, DCC OVP-12G protects both 12 V through 15 V outputs PEAK CURRENT MODELS N, BAA, CBB 131 OVP-12G protects any output not provided with built-in OVP

Surface Mount PTC - Bel Fuse

6. If potting is mandated, avoid rigid potting compounds as they will encase the PTC and prevent it from volumetrically expanding to properly respond to a trip event. 7. MSL: 2a (According to IPC J-Std-020). P S W Nominal Nominal Nominal mm Inch mm Inch mm Inch 2.00 0.079 1.00 0.039 1.90 0.075 All dimensions in mm. Part Number

  Compound, Potting, Potting compounds

°C

Solder Reflow Due to “lead free / RoHS 2 ” construction of these PTC devices , the required Temperature and Dwell Time in the “ Soldering ” zone of the reflow profile are greater than those used for non-RoHS devices. 1. Recommended reflow methods; IR, vapor phase oven, hot air oven. 2. Not Recommended For Wave Solder / Direct Immersion. 3.

  Free, Deal, Solder, Lead free

AEC-Q Compliant - Bel Fuse

n 0zcg0300ff2b 3.00 5.00 6 100 1.0 8.0 4.000 0.012 0.040 y y IH Hold Current- The maximum current at which the device will not trip in still air at 23°C. IT Trip current- The minimum current at which the device will trip in still air at 23°C.

HxxxFD(N/P)

Take ohm reading of keypad. The membrane switch has a 4-pin connector on the end of the ribbon cable. Measure using holes in top of connector. To test the MODE button, measure resistance across pins 1 and 4. To test the UP button, measure resistance across pins 2 and 4. To test the DOWN button, measure resistance across pins 3 and 4.

  Connectors

ARTICLE 625 Electric Vehicle Charging and Supply Equipment ...

connector is inserted for power transfer and information exchange. This device is part of the electric vehicle coupler. ... gas pressure during normal charging and operation, or for the addition of water or electrolyte, or for external measurements of electrolyte specific gravity.

  Connectors

SPECIFICATION GUIDE - StrongArm Gas Charged LIft …

Select the Extended Length of the Gas Spring • Measure your existing gas spring from the center point of each end fitting – “A” • Identify the connector type (eyelet/ball socket). • Capture all markings on tube; specially noting pressure which is identified as xxx#’s or xxxN.

  Guide, Specification, Connectors, Guide specification

AS/NZS5601.1:2013 Gas installations

appliance/equipment manufacturers, gas companies and technical regulators. In Queensland, the current Australian Standard for gas fitting in domestic, commercial and industrial situations is the AS/NZS5601.1:2010 Gas Installations Part 1: General Installations. This standard was recently revised and republished on 16 September 2013.