15. Synthesis of a Polymer: Nylon-6,6
Nylon 6,6, which you will prepare in today’s lab experiment is an example of an alternating copolymer because it contains alternating diamine and dicarbonyl units. The 6,6 numbering refers to the number of carbon atoms in the diamine and dicarbonyl units, respectively. Another
Download 15. Synthesis of a Polymer: Nylon-6,6
Information
Domain:
Source:
Link to this page:
Documents from same domain
Crystal Structure of Graphite, Graphene and Silicon
community.wvu.eduCrystal Structure of Graphite, Graphene and Silicon Dodd Gray, Adam McCaughan, Bhaskar Mookerji∗ 6.730—Physics for Solid State Applications (Dated: March 13, 2009)
What we did on the computers last class Sec. 4.2-4
community.wvu.eduWhat we did on the computers last class Sec. 4.2-4.6. MAE 340 – Vibrations 2 ... used to simplify a MDOF analysis into a several SDOF analyses: Mapping Eigenvalue MAE 340 – Vibrations 9 problem to SDOF problem ... individual dampers in a Modal Analysis.
SWE 621: Software Design Lecture Notes on Software Design
community.wvu.eduSWE 621: Software Design Lecture Notes on Software Design Spring Semester 2002 Hassan Gomaa Dept of Information & Software Engineering George Mason University ... Software Construction Detailed Design Internal design of individual components Design of logic and data structures Coding
Plates and Shells - West Virginia University
community.wvu.edu1 MAE456 Finite Element Analysis Plates and Shells All images are from R. Cook, et al. Concepts and Applications of Finite Element Analysis, 1996.
Using SolidWorks for Finite Element Analysis – in 12 Easy ...
community.wvu.eduUsing SolidWorks for Finite Element Analysis – in 12 Easy Steps 1. Before starting the FEA of the structure, do some hand calculations to determine approximately what results (stresses or deflections) you should expect. Assume simplified geometry and loads. 2. Create a solid model of the part you wish to analyze. (In general, it does not need to
Chapter 8 : Sequence Diagram - West Virginia University
community.wvu.eduChapter 8 : Sequence Diagram The Sequence Diagram What is a Sequence Diagram This diagram is a model describing how groups of objects collaborate in some behavior over time. The diagram captures the behavior of a single use case. It shows objects and the messages that are passed between these objects in the use case. When to use a sequence diagram
9. Hydroboration-Oxidation of Alkenes
community.wvu.eduthis washing procedure with one additional 0.5 mL portion of brine. Prepare a sodium sulfate drying column (a small pipet plugged with a wad of cotton followed by the addition of 0.5 cm of sand and 3 cm of anhydrous Na 2SO 4). Transfer your organic layer to the drying column and collect the dried solution in a pre-weighed conical vial.
16. Electrophilic Aromatic Substitution
community.wvu.eduAromatic compounds are extremely important for their industrial and pharmaceutical use. A few prescription drugs containing one or more aromatic rings are shown in figure 2. With their immense value as synthetic targets, it is important to understand both the properties and the reactivity of aromatic rings.
Plates and Shells - West Virginia University
community.wvu.eduPlates and Shells All images are from R. Cook, et al. Concepts and Applications of Finite Element Analysis, 1996. MAE456 Finite Element Analysis 2 Plate Formulation • Plates may be considered similar to beams, however: – Plates can bend in two directions – Plates are flat with a thickness (can’t have an interesting cross-section)
Crystal Structure of Graphite, Graphene and Silicon
community.wvu.eduMar 13, 2009 · lar to the graphene sheet. The corresponding ABCABC layer forms a rhombohedral structure with identical lat-tice spacing parallel and orthogonal to the layer. 1.2. Reciprocal Lattice Structure Recall that the reciprocal lattice vectors bi are defined as a function of the primitive lattice vectors ai such that b1 = 2π a2 ×a3 a1 ·a3 ×a3 b2 ...
Related documents
Specifications - CJT
cjt.com1.00mm pitch wire to board connector A1002HG-XP 1.00mm pitch 180° Single Row Housing Reference Informations: *Material:Nylon 66,UL94V-0 *Suitable CJT A1002A-T series Terminal *Mates with CJT A1002WRC-S-XP series Wafer
OPERATOR'S MANUAL 56-VOLT LITHIUM-ION CORDLESS 15 …
egopowerplus.com6 56-VOLT LITHIUM-ION CORDLESS 15" STRING TRIMMER IMPORTANT SAFETY INSTRUCTIONS WARNING! When using electric trimmers, basic safety precautions should ... line or other material in place of the nylon cutting lines. Pieces of wire could break off and be thrown at high speed toward the operator or bystanders.
Technical Information Bulletin
static.nhtsa.govPort E, Option 1 • 2.1m Aux Heater or 2 nd Drivetrain Cooler • OR 1.9m Aux Heater • Brass: D2111-3603 & V88-1109 • Composite: V38-1166 and V88-
Hoisting & Rigging Fundamentals - Energy
www.energy.govat WVNS: nylon and polyester. Nylon is the most common type used on site. It has an elastic stretch of 6% at noted capacity. Polyester has less stretch, approximately 3 percent. The stretching of slings allows a cushion against sudden shock. Both types are sensitive to heat and certain chemicals. Neither should be exposed to
One-Piece Instrumentation Ball Valves - Swagelok
www.swagelok.comNylon with powdered metal 300 series SS insert 2 Set screw S17400/A564 3 Packing bolt Powdered metal 300 series SS 4 Springs S17700/A693 5 Gland Powdered metal 300 series SS 6 Ball stem 316 SS/A276 7 Packing Modified PTFE/D1710 type 1, Grade 1, Class B or UHMWPE/D4020 8 Side rings Powdered metal 9 Side discs 300 series SS/B783
Glass Filled Nylon Technical Properties Data Sheet
www.theplasticshop.co.ukGlass Filled Nylon Technical Properties Data Sheet Author: www.theplasticshop.co.uk Subject: Provides technical data and properties for glass filled nylon rod, sheet and tube Keywords: glass, filled, nylon, technical, data, sheet, properties, information Created Date: 1/21/2011 11:38:51 AM
CHEMICAL RESISTANCE CHART - U.S. Plastic
www.usplastic.com6. Ceramag — Satisfactory to 72° F. CHEMICAL RESISTANCE DATA These recommendations are based upon information from material suppliers and careful examination of available published information and are believed to be accurate. However, since the resistance of metals, plastics and elastomers can be affected by concentration, temperature ...