9. Hydroboration-Oxidation of Alkenes
this washing procedure with one additional 0.5 mL portion of brine. Prepare a sodium sulfate drying column (a small pipet plugged with a wad of cotton followed by the addition of 0.5 cm of sand and 3 cm of anhydrous Na 2SO 4). Transfer your organic layer to the drying column and collect the dried solution in a pre-weighed conical vial.
Tags:
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
Crystal Structure of Graphite, Graphene and Silicon
community.wvu.eduCrystal Structure of Graphite, Graphene and Silicon Dodd Gray, Adam McCaughan, Bhaskar Mookerji∗ 6.730—Physics for Solid State Applications (Dated: March 13, 2009)
Structure, Crystal, Graphene, Graphite, Crystal structure of graphite, Graphene and
What we did on the computers last class Sec. 4.2-4
community.wvu.eduWhat we did on the computers last class Sec. 4.2-4.6. MAE 340 – Vibrations 2 ... used to simplify a MDOF analysis into a several SDOF analyses: Mapping Eigenvalue MAE 340 – Vibrations 9 problem to SDOF problem ... individual dampers in a Modal Analysis.
Analysis, Computer, Class, Salt, Modal, Ofdm, Modal analysis, On the computers last class sec, Mdof analysis
SWE 621: Software Design Lecture Notes on Software Design
community.wvu.eduSWE 621: Software Design Lecture Notes on Software Design Spring Semester 2002 Hassan Gomaa Dept of Information & Software Engineering George Mason University ... Software Construction Detailed Design Internal design of individual components Design of logic and data structures Coding
Lecture, Notes, Design, Construction, Software, Software design lecture notes on
Plates and Shells - West Virginia University
community.wvu.edu1 MAE456 Finite Element Analysis Plates and Shells All images are from R. Cook, et al. Concepts and Applications of Finite Element Analysis, 1996.
Using SolidWorks for Finite Element Analysis – in 12 Easy ...
community.wvu.eduUsing SolidWorks for Finite Element Analysis – in 12 Easy Steps 1. Before starting the FEA of the structure, do some hand calculations to determine approximately what results (stresses or deflections) you should expect. Assume simplified geometry and loads. 2. Create a solid model of the part you wish to analyze. (In general, it does not need to
Analysis, Using, Elements, Finite, Solidworks, Using solidworks for finite element analysis
Chapter 8 : Sequence Diagram - West Virginia University
community.wvu.eduChapter 8 : Sequence Diagram The Sequence Diagram What is a Sequence Diagram This diagram is a model describing how groups of objects collaborate in some behavior over time. The diagram captures the behavior of a single use case. It shows objects and the messages that are passed between these objects in the use case. When to use a sequence diagram
16. Electrophilic Aromatic Substitution
community.wvu.eduAromatic compounds are extremely important for their industrial and pharmaceutical use. A few prescription drugs containing one or more aromatic rings are shown in figure 2. With their immense value as synthetic targets, it is important to understand both the properties and the reactivity of aromatic rings.
15. Synthesis of a Polymer: Nylon-6,6
community.wvu.eduNylon 6,6, which you will prepare in today’s lab experiment is an example of an alternating copolymer because it contains alternating diamine and dicarbonyl units. The 6,6 numbering refers to the number of carbon atoms in the diamine and dicarbonyl units, respectively. Another
Plates and Shells - West Virginia University
community.wvu.eduPlates and Shells All images are from R. Cook, et al. Concepts and Applications of Finite Element Analysis, 1996. MAE456 Finite Element Analysis 2 Plate Formulation • Plates may be considered similar to beams, however: – Plates can bend in two directions – Plates are flat with a thickness (can’t have an interesting cross-section)
Crystal Structure of Graphite, Graphene and Silicon
community.wvu.eduMar 13, 2009 · lar to the graphene sheet. The corresponding ABCABC layer forms a rhombohedral structure with identical lat-tice spacing parallel and orthogonal to the layer. 1.2. Reciprocal Lattice Structure Recall that the reciprocal lattice vectors bi are defined as a function of the primitive lattice vectors ai such that b1 = 2π a2 ×a3 a1 ·a3 ×a3 b2 ...
Related documents
Validation Standard Operating Procedures
elsmar.com100.10 Introduction to Validation Section VAL 200.00 ... 700.40 Ampule and Vial Washing Machine 700.50 Washing, Sterilizing, and Drying Machine for Stoppers 700.60 Ampule and Vial Filling Machine 700.70 Media Fill Run 700.80 Half-Automatic Inspection Machine
Introduction, Operating, Standards, Validation, Procedures, Washing, Vial, Validation standard operating procedures, Vial washing
Synthesis and Analysis of Acetyl Salicylic Acid
joshstaiger.orgIntroduction Acetyl salicylic acid, commonly known as aspirin, is one of the most common synthetic medicines. ... These washing steps had to be performed quickly to minimize the loss of aspirin due to its solubility in water. ... crystals were in the oven, a clean, dry vial was appropriately. This vial was weighed on a top load balance, and the ...
Expt 9: The Aldol Condensation - Towson University
tigerweb.towson.edusolids in the vial with a microspatula to make them easier to transfer. Pour the contents of the vial onto the Hirsch funnel and filter the solid. 9. To ensure complete transfer of all the solids into the Hirsch funnel, wash out the conical vial twice, using two 3 mL portions of DI water, transferring all washings into the Hirsch funnel each time.
Infection Control/ Bloodborne Pathogens
nt.prophecyhealth.comhand-washing guidelines and maintain a sterile field). Never administer medications from the same syringe to more than one patient, even if the needle is changed. Never enter a vial with a used syringe or needle. Do not use medications packaged as single-dose or single-use for more than one patient.
tuberculin skin test
www.cdc.govInvert the vial while keeping a firm hold on the syringe and plunger. The tip of the needle should be below the fluid level in the vial. Pull back on the plunger and draw out slightly more than the one tenth of a milliliter needed for the test. Remove the needle from the vial. Hold the syringe in an upright position, then draw back slightly on
Inherent Factors Affecting Soil pH - Home | NRCS
www.nrcs.usda.govThe vial will contain a 1:1 ratio of soil to water, on a volume basis. 3. Tightly cap vial and shake 25 times. Let the sample settle for 1 minute. Remove cap and decant 1/16inch of soil-water solution carefully into lid. Let sample sit in the lid for 2 to 3 minutes. 4. Take the end of a 1-inch-long piece of pH paper ...
Experiment 11: Dehydration of Cyclohexanol
tigerweb.towson.eduto the funnel. (This process is called “washing”.) The NaOH removes any trace of acid that may have co-distilled with the product. The aqueous layer is carefully removed, leaving the product in the funnel. The “wet” product is then transferred to a …