2015 Plumbing Rough In Checklist - MyBuildingPermit
Vents terminate a minimum 6” above roof line (10” in high snow load areas). (UPC 906.1 & 906.7) Vent clearance to building openings are 3’ above or 10’ horizontal. (UPC 906.2) Air-Admittance Valves Minimum 4” above drain. (Per local jurisdiction and manufacturer’s installation instructions ) Minimum 6” above insulation in attic.
Download 2015 Plumbing Rough In Checklist - MyBuildingPermit
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
Residential Building Final
mybuildingpermit.comHandrails and guards capable of withstanding 200 lbs. applied in any direction at any point on the rail. (IBC 1607.8.1.1) Handrail at stairs with 4 or more risers. (R311.7.8) Handrail minimum 34" to maximum 38" above nose of tread to top of handrail. (R311. 7.8.1) Type I handrails with circular cross sections 1 1/4” - 2" diameter.
Smoke and carbon monoxide alarms must be provided in all ...
mybuildingpermit.com• Smoke alarms and carbon monoxide alarms shall be located on every floor level, including basements (does not include crawlspace and uninhabitable attics). • In split level floor plans, at the upper level, provided there is no intervening door between adjacent levels and the lower level is less than a full story below the upper level
CONSTRUCTION TIP SHEET 19 Safety Glazing - …
mybuildingpermit.comglass and safety glazing standard to which it complies. The label must be permanently etched, fired, or embossed, on the glass or be a type that once applied cannot be removed without being destroyed. Safety Glazing Required Locations: 1. Glazing in Doors: Safety glazing is required in fixed and operable panels of swinging, sliding, and bifold ...
Converting a Garage to Living Space - Welcome to MBP | MBP
mybuildingpermit.comopening. In these cases it is often required to dig under the slab and add a footing to support the new wall above. The figure to the right shows one way that can be done. For other options speak to your jurisdiction. Excavation may be required to verify the existing slab thickness. Energy Code Requirements If your project does not meet the ...
INSPECTION CHECKLIST Residential Re-roof
mybuildingpermit.comWhen the application of new roof covering over wood shingle or shake roofs creates a combustible concealed space, the entire existing surface is to be covered with gypsum board, mineral fiber, glass fiber or other approved material and securely fastened in place. (R908.4)
Applications, Checklist, Material, Residential, Roof, Inspection, Woods, Inspection checklist residential re roof
What are Deferred Submittals? - MyBuildingPermit
mybuildingpermit.comdesign professional is required, shall list the deferred submittals on the construction documents for review by the building official. C. Generally, if an element has not been reviewed and approved under the original permit, it is required to be submitted as a deferred submittal to the City for review and approval.
Inspection Checklist Residential Fuel ... - MyBuildingPermit
mybuildingpermit.coma building if sleeved in schedule 40 steel, iron, or plastic pipe conduit extending at least 4 inches to outside of building. (G2415.14) The interior end of the conduit enclosing the gas pipe is sealed. (G2415.14.1) The exterior end of the conduit is a minimum 4 inches outside of the building, vented above grade and
Related documents
2020 FBC Roof Packet - Broward County
www.broward.orgIndicate: Mean Roof Height, Parapet Height, Height of Base Flashing, Component Material, Material Thickness, Fastener Type, Fastener Spacing or Submit Anchor/Base Sheet & No. of Ply(s): Anchor/Base Sheet Fastener/Bonding Material: Insulation Base Layer: Base Insulation Size and Thickness: Base Insulation Fastener/Bonding Material:
EVERGUARD TPO/PVC MECHANICALLY ATTACHED - GAF
www.gaf.com2.07 Insulation 39 2.08 High Traffic Applications 40 2.09 Cover/Re-cover Boards 40 2.10 Base Sheets 41 2.11 Slip Sheet/Protection Layer 41 2.12 Other Accessories 41 Part 3: Execution 3.01 Site Conditions 41 3.02 Preparation of Roofing Area - New & Tear-off Applications 41 3.03 Preparation of Roofing Area - Re-cover Applications 41
Plaster Systems Brochure (English) - SA920 - USG
www.usg.com–5/89 panel can be substituted for 5/8 i9mpeRial Brand FiRecoDe Core Gypsum Base and certain 1/2 9impeRial Brand FiRecoDe C Core Gypsum Base in wall assemblies without compromising the fire rating (see Application Guide Specifications, Part 3.3.5) – Refer to product submittal sheet F218 for more information impeRial® Brand Gypsum Base
Standard Details for Metal Roofing & Siding - Best Materials
www.bestmaterials.comnail available for steel panels when screws are not desired. The correct way to fasten steel panels with nails is to drive the nail through the top of the rib so the washer is compressed securely against the metal. Nail placement must be in the ribs for roofing ap-plications to minimize the potential for roof leaks. Over-driving the nail
Technical Note - Roofs - Queensland
www.qld.gov.au5. Roof structure—timber, steel or a combination of these materials make up the roof structure of most heritage-listed buildings. 6. Roof installations—aerials, satellite dishes, air conditioning units, solar panels, safety systems etc. Context The roof may be considered to be the most important part of the building.
Roof Insulations - Johns Manville
www.jm.comRoof Insulation Asphalt or Cold Adhesive Wood or Plywood Roof Deck Base Sheet Roofing Nail (Minimum 1" Head or Cap) 7 UltraFast Fastener and Metal Plate Roof Insulation Steel Roof Deck 1 UltraFast Fastener and Plastic Plate Roof Insulation Steel Roof Deck 2 Polymer Auger Fastener with Plate Roof Insulation Cementitious Wood Fiber or Gypsum Roof ...
USG DUROCK BRAND CEMENT BOARD SYSTEMS
www.usg.comUSG Durock® Brand Cement Board offers architects, builders and tile contractors a strong, water-durable tile base for tub and shower areas. Also an ideal underlayment for tile on floors and countertops in new construction and remodeling. Board is readily applied over wood or steel framing spaced 16" o.c. with corrosion-resistant wood or steel
Pro Field Guide - GAF
www.gaf.comTear Off Or Install Two Roof Layers, Tearing Off Roof Good Practices Tearing Off Old Roofing (Review #3)..... 29 Dealing with Decks..... 30-38 Roof Deck Basics, Installing Plywood, Insulation and Other Decks, ThermaCal® Nail Base Roof Insulation Panels,
OUTSULATION - Dryvit
www.dryvit.comnail-on window window head os 0.0.11 termination at os 0.0.12 wood framed deck ... cap flashing termination at parapet - os 0.0.16 solid substrate termination at sloped roof os 0.0.17 vertical wall/suspended os 0.0.18 soffit transition transition at soffit/ os 0.0.19 fascia intersection ... dryvit base coat eps insulation dryvit base coat ...