3. STEAM SYSTEM
Apart from proper sizing of pipe lines, provision must be made for proper draining of condensate which is bound to form as steam travels along the pipe. For example, a 100 mm well lagged pipe of 30-meter length carrying steam at 7 kg/cm2 pressure can condense nearly 10 kg. of water in the pipe in one hour unless it is removed from
Download 3. STEAM SYSTEM
Information
Domain:
Source:
Link to this page:
Documents from same domain
7. COOLING TOWER - Bureau of Energy Efficiency
www.beeindia.gov.inCooling Tower:Types and performance evaluation, Efficient system operation, Flow control strategies and energy saving opportunities, Assessment of cooling towers Cooling towers are a very important part of many chemical plants.
3. ENERGY PERFORMANCE ASSESSMENT OF …
www.beeindia.gov.in3. Energy Performance Assessment of Cogeneration and Turbine Bureau of Energy Efficiency 46 3.4 Reference standards Modern power station practices by British electricity International (Pergamon Press) ASME PTC 22 - Gas turbine performance test. 3.5 Field Testing Procedure
10. ENERGY EFFICIENT TECHNOLOGIES IN ELECTRICAL SYSTEMS
www.beeindia.gov.inAutomatic power factor controllers, Energy efficient motors, Soft starters with energy saver, Variable speed drives, Energy efficient transformers, Electronic ballast, Occupancy sensors, Energy efficient lighting controls, Energy saving potential of each technology. 10.1. Maximum Demand Controllers
2. BOILERS
www.beeindia.gov.in2. BOILERS Bureau of Energy Efficiency 27 Syllabus Boilers: Types, Combustion in boilers, Performances evaluation, Analysis of losses, Feed water treatment, Blow down, Energy conservation opportunities. 2.1 Introduction A boiler is an enclosed vessel that provides a means for combustion heat to be transferred into water until it becomes heated water or steam.
5. INSULATION AND REFRACTORIES
www.beeindia.gov.inInsulation and Refractories: Insulation-types and application, Economic thickness of insulation, Heat savings and application criteria, Refractory-types, selection and application of refractories, Heat loss. 5.1 Purpose of Insulation A thermal insulator is a poor conductor of heat and has a low thermal conductivity. Insulation
Chapter: 1.1 Energy Scenario Part-I: Objective type ...
www.beeindia.gov.inThe major sources of pollutants in Air are fuel combustion in transport, industry, forest fires, and solid waste disposal. 12. What is greenhouse gas effect? The heating up of earth’s atmosphere due to trapping of long wavelength infrared rays by the carbon di- oxide layer in the atmosphere is called green house effect. 13.
5. FANS AND BLOWERS
www.beeindia.gov.inCentrifugal blowers look more like centrifugal pumps than fans. The impeller is typically gear-driven and rotates as fast as 15,000 rpm. In multi-stage blowers, air is accelerated as it passes through each impeller. In single-stage blower, air does not take many turns, and hence it …
Question bank for Energy Managers & Energy Auditors
www.beeindia.gov.inenergy plays in the continued viability of their job (4) the many ways they can save energy in their operation (5) the relationship between production rate and energy consumption. 15. From energy conservation act-2001, list four important duties of an Energy manager.
12. APPLICATION OF NON-CONVENTIONAL & RENEWABLE …
www.beeindia.gov.inwater, sailing ships - have been used for centuries. Now wind power is harnessed to generate electricity in a larger scale with better technology. Wind Energy Technology The basic wind energy conversion device is the wind turbine. Although various designs and configurations exist, these turbines are generally grouped into two types: 1. Vertical ...
4. ENERGY PERFORMANCE ASSESSMENT OF HEAT …
www.beeindia.gov.inOF HEAT EXCHANGERS Bureau of Energy Efficiency 55 4.1 Introduction Heat exchangers are equipment that transfer heat from one medium to another. The proper design, operation and maintenance of heat exchangers will make the process energy efficient and minimize energy losses. Heat exchanger performance can deteriorate with time, off
Related documents
STEAM TRAPS & SPECIALTIES DESIGNER’S GUIDE
www.albindustrial.comDESIGNER’S GUIDE STEAM TRAPS & SPECIALTIES STEAM TRAPSTEAM TRAP • Mechanical Steam Traps • Thermostatic Steam Traps • Thermodynamic Steam Traps • Condensate Pumps • Compressed Air Products • Gasketed Unions • Sanitary Steam Products • Drain Orifice Steam Traps Nicholson steam traps are manufactured by Spence Engineering.
DRI-STEEM
www.dristeem-media.comREAD AND SAVE THESE INSTRUCTIONS DRI-STEEM STEAM INJECTION HUMIDIFIERS Installation Instructions and Maintenance Operations Manual ® DS-IOM-0300.pdf 1 4/21/2010 10:58:36 AM
Tech Sheet #ST 101 - Fluid Controls Institute
www.fluidcontrolsinstitute.orgThis Tech Sheet was developed by the members of the Fluid Controls Institute (FCI) Steam Trap Section. FCI is a trade association comprising the
Steam Traps - Armstrong International
www.armstronginternational.com(Steam Trap Sizing and Selection) is designed to be used in conjunc-tion with Handbook N-101 and this ... ence in density between condensate and steam—the inverted bucket principle. They open and close gently, minimizing wear. This ... tube having a pipe coupling at the top to save fittings, labor and money. See Fig. 8-1.
Pipe Sizing Steam Supply andCondensateReturn Lines
www.armstronginternational.comPipe Sizing Steam Supply and Condensate Return Lines Definitions Steam mains or mains carry steam from the boiler to an area in which multiple steam-using units are installed. Steam branch lines take steam from steam main to steam-heated unit. Trap discharge lines move condensate and flash steam from the trap to a return line.
FLUID FLOW BASICS OF THROTTLING VALVES
www.controlglobal.com∆Psize – Sizing Pressure Drop Vapor Pressure PVP1, ... v1P _____ Avg. Pipe Velocity _____ v2P µ1 ... we have both saturated liquid water (condensate) and satu-rated steam at the same Psat and Tsat. Further, for any given fluid in its “saturation” state, when we have its pressure ...
Steam System Design and Best Practices Related to Kiln Drying
www.esf.eduNew England Kiln Drying Association – Steam Design & Best Practices – HerLine Technologies Steam Distribution System Proper layout design & pipe sizing of mains Piping always pitched in the direction of flow Use of eccentric reducers to eliminate creation of condensate collection points (low spots) in piping
ENGINEERING MANUAL Industrial Boilers
www.inscogroup.comCondensate tank Feed pumps Steam boiler Deaerator Level sensor Level sensor Condensate pumps . Ver 01. 18/12/2008 ... A non-return valve must be installed on the suction pipe of the boiler. ... Requirements vary from one country to another as to the sizing of condensate pumps (two pumps must always back up each other 100 %, requirements as to ...