ASEPTIC PACKAGING SYSTEM
The package must be able to withstand heat up to about 100°C for high acid products and up to 127°C for low acid products, which must ... as part of the process-heat is recovered through the heat exchangers and the aseptic ... Equipment Product Aroma Energy Capital Space Pulp Fouling Turn-Type Quality Reten- Savi ng Cost Capabi- Length down*
Download ASEPTIC PACKAGING SYSTEM
Information
Domain:
Source:
Link to this page:
Documents from same domain
PACKAGING OF READY-TO-EAT/READY-TO- COOK FOOD
www.icpe.inThe advancements in food technology and packaging technology have made it possible to extend the shelf-life of these products. Before deciding which packaging material is to be ... • The type of food and its composition, moisture, fat, protein, flavour etc.
INTRODUCTION TO FOOD PACKAGING - ICPE
www.icpe.inaddition of substances like sugars, salts or acids or exposure of food to chemicals, Fig. 1.1. Methods of food preservation 5 ... The food processing sector had a market size of Rs 4,60,000 crore in 2003-04 and is expected to grow at 7.3% in the next five years. Food packaging,
Related documents
5.1 Shell-and-Tube Heat Exchangers
homepages.wmich.eduShell-and-tube heat exchangers can have multiple passes, such as 1-1, 1-2, 1-4, 1-6, and 1-8 exchangers, where the first number denotes the number of the shells and the second number denotes the number of passes. An odd number of tube passes is seldom used except the 1-1 exchanger. A 1-2 shell-and-tube heat exchanger is illustrated in Figure 5.19.
Chapter 16 HEAT EXCHANGERS - SFU
www.sfu.caFouling represents additional resistance to heat transfer and causes the rate of heat transfer in a heat exchanger to decrease, and the pressure drop to increase. 16-17C The effect of fouling on a heat transfer is represented by a fouling factor R f .
Product WEATHERMASTER® 48HJ004-028 Data Single …
ceae.colorado.edutioned space is calling for heat to maximize efficiency. The direct-spark ignition system saves operating expense when com-pared to pilot ignition systems. No crossover tube is required, therefore no sooting or pilot fouling problems can occur. All standard units are …
Heat exchanger design handbook - GBV
www.gbv.dePerformanceFailures,Flow Maldistribution,Fouling,andCorrosion 125 3.5.1 HeatExchangerPressure-DropAnalysis 125 3.5.1.1 Pressure-DropEvaluation for HeatExchangers 125. X Contents 3.5.1.2 PressureDropthrough aHeatExchanger 126 3.5.1.3 ShellandTubeHeat Exchangers 127
Specifying Shell-and-Tube Heat Exchangers
stoppingclimatechange.comShell-and-tube heat exchangers are one of the most important and commonly used process equipment items in the chemical process industries (CPI). If you are working on a project during either the basic or the detailed engineering phase, there is a good chance that you will need to specify one or more shell-and-tube exchangers — and perhaps ...
The theory behind heat transfer
www.alfalaval.comHeat exchangers A heat exchanger is a piece of equip-ment that continually transfers heat from one medium to another. There are two main types of heat ... the fouling of the heat transfer surfaces is considerably reduced. This means that the …
E1-MNL032A - Design and Rating of Shell and Tube Heat ...
www.chemstations.comShell and Tube Heat Exchangers PAGE 3 OF 30 MNL 032A Issued 29 August 08, Prepared by J.E.Edwards of P & I Design Ltd, Teesside, UK www.pidesign.co.uk 1. 0 Introduction Shell and tube heat exchangers are used extensively throughout the …
Free Cooling Using WaterEconomizers - Trane
www.trane.comwater heat exchangers used as part of a water economizer system shall either have a water-side pressure drop of less ... greatly increases the risk of fouling in the chilled-water system and cooling coils with the same type of contamination that …