ceilings - Rondo

finishing sections - Rondo

the flexible joint section to keep it clean when applying the setting compound, and is removed on completion. Used in both stud walls and flush building board ceilings, the P35 has been designed for movement of up to 5mm in each direction. PVC is inherently flame resistant in the

  Testing, Compound, Flexible, Setting compound

INSTALLATION GUIDE - Rondo

3.FIX PLASTERBOARD Screw fix plasterboard, tape and set joints and sand off as lining manufacturers recommendations. FIGURE 8: KEY-LOCK® USED TO BATTEN-OUT MASONRY WALL Maximum spacings: For 308: 900mm For 129: 1200mm 25mm 25mm 600mm maximum Anchor clips (eg. BETAGRIP) BetaGrip® Clips can be installed to a wall with either one centre …

  Plasterboard

Design Manual Keylock Ceiling System - Home | Rondo

Suspended Ceiling System is designed to produce high quality structure for a flawless, flush or featured finish. ... be staggered throughout the ceiling grid (refer to building board manufacturer for recommended spacing). STEP SIX Install lining sheet as per the building board manufacturer’s

  Grid, System, Ceiling, Ceiling system, Grid ceiling

INSTALLATION GUIDE - Rondo

SNAP-LOCK NOGGING® The Rondo SNAP-LOCK Nogging ® is designed for use with Rondo 0.50 and 0.55bmt lightweight studs. SNAP-LOCK clips into the bellmouth service holes in a continuous, overlapping manner after the framing is installed. It is important to ensure the service holes align vertically. FAST-FIX NOGGING®

  Guide, Installation, Span, Installation guide

walls - Home | Rondo

plasterboard walls and for specific external wall systems. The availability of various sizes, complimentary components such as noggin tracks, curved tracks and special cleats ensure Rondo Stud and Track wall systems are available to suit almost all situations. SUITABLE FOR: • Non-load bearing partition walls • Load Bearing Walls by design

  Special, Walls

Acoustical Ceiling Design & Application

DONN DX Suspension System is an exposed 24 mm (15/16 ) wide face grid. It is the most commonly used suspension system. Note that exposed face grid products are typically differentiated by the width of the exposed portion and/or by reveals in the exposed portion. DONN CENTRICITEE Suspension System is an exposed 14 mm (9/16 ) wide face

  Design, Ceiling, Acoustical, Suspension, Exposed, Acoustical ceiling design

SUSPENSION SYSTEMS ACCESSORIES GUIDE

USG SUSPENSION SYSTEMS ACCESSORIES MT/CT Converter F Two-Way Seismic Separation Joint Clip G1 Three-Way Off-Module Connector G2 Changes main-tee direction 90° from adjacent main tee. For seismic separation joints in IBC Seismic Design Categories D, E and F. Use with cross tees and main tees that are the same height.

  System, Suspension, Suspension systems, Usg suspension systems

EXPOSED TEE SUSPENSION SYSTEMS ACCESSORIES

EXPOSED TEE SUSPENSION SYSTEMS ACCESSORIES. 2" Beam End Retaining Clip – Joins main beam or cross : tee to wall molding and web of suspension system with no visible pop rivets. ALBERC2 (aluminum) – 200 pcs: FZALBERC2 (aluminum) – 50 pcs BERC2 (steel) – 200 pcs. FZBERC2 (steel) – 50 pcs:

  System, Suspension, Exposed, Exposed tee suspension systems

PRELUDE XL and PRELUDE XL High Recycled Content (HRC)

4' Cross Tee 12" O.C. 48 x 15/16 x 1-11/16" 12.25 N/A N/A • • • • • • • • • 60 60 240 240 XL7342_ _ _ 4' Cross Tee 12" O.C. 48 x 15/16 x 1-1/2" 7.8 N/A N/A • • • • 60 240 XL7348_ _ 4' Cross Tee 12" O.C. 48 x 15/16 x 1-3/8" 6.78 N/A N/A • • • • 60 240 XL7330_ _ ††† …