DIMENSIONS - KitchenAid
" (19.1 cm) minimum clearance is required from the cutout or 6" (15.2 cm) minimum clearance from the back edge of the rangetop. Unlike many cooktops, these models do not hang from the side flanges, but rather sit on the floor of the cutout.
Download DIMENSIONS - KitchenAid
Information
Domain:
Source:
Link to this page:
Documents from same domain
Use & Care Guide - kitchenaid.com
www.kitchenaid.com3 INSTALLATION INSTRUCTIONS Installer: Leave Use and Care Guide with the homeowner. Homeowner: Keep Use and Care Guide for future reference and for local electrical inspector’s use, if required. Unpacking IMPORTANT: Do not grasp console to move compactor. Begin in the room where the compactor will be located. 1. Remove compactor from shipping carton.
KSMSFTA - kitchenaid.com
www.kitchenaid.comPrecise Heat Mixing Bowl, Ice Cream Maker, or the Pouring Shield. The Sifter+Scale attachment can be used in multiple ways: to weigh and sift ingredients while ... WARRANTY AND SERVICE KITCHENAID SIFTER+SCALE ATTACHMENT WARRANTY FOR THE 50 UNITED STATES, THE DISTRICT OF COLUMBIA, PUERTO RICO, AND CANADA
KITCHENAID ICE MAKER WARRANTY
www.kitchenaid.com19 KITCHENAID® ICE MAKER WARRANTY THREE YEAR LIMITED WARRANTY (PARTS AND LABOR) For three years from the date of purchase, when this major applia nce is installed, operated and maintained according to instructions
KITCHENAID DISHWASHER WARRANTY
www.kitchenaid.com21 KITCHENAID® DISHWASHER WARRANTY TWO YEAR LIMITED WARRANTY For two years from the date of purchase, when this major appliance is operated and maintained according to instructions attache d to or
BOWL LIFT STAND MIXER
www.kitchenaid.comreplacement stand mixer, use the carton and packing materials to pack up your “failed” stand mixer. In the carton, include your name and address on a sheet of paper along with a copy of the proof of purchase (register receipt, credit card charge slip, etc.). For a detailed explanation of warranty terms and conditions, including how to ...
STAND MIXER - KitchenAid
www.kitchenaid.comreplacement stand mixer, use the carton and packing materials to pack-up your “failed” stand mixer. In the carton, include your name and address on a sheet of paper along with a copy of the proof of purchase (register receipt, credit card charge slip, etc.). For a detailed explanation of warranty terms and conditions, including how to ...
Use & Care Guide
www.kitchenaid.comWhen using electrical appliances, basic safety precautions should always be followed, including the following: 1. Read all instructions. Misuse of appliance may result in personal injury. 2. To protect against risk of electrical shock, do not put Stand Mixer in water or other liquid. 3. This appliance can be used by children aged from 8 years
Owners Manual - KitchenAid
www.kitchenaid.comDrying - Rinse aid is essential. You must use a drying agent such as a rinse aid for good drying performance (sample included). Rinse aid along with the Heat Dry or ProDry™ option will provide best drying and avoid excessive moisture in the dishwasher interior. For best drying, use the Heat Dry or ProDry™ option. Dispensers vary by model
INSTALLATION INSTRUCTIONS 27 (68.6 CM) AND 30 (76.2 CM ...
www.kitchenaid.com4 Cabinet Dimensions - Double Ovens, Flush Installations A 253/ 8" (64.4 cm) minimum cutout depth is required. These dimensions will result in a 1/4" (6 mm) reveal on the top, a 1/4" (6 mm) reveal on the sides, and a 1/8" (3 mm) reveal on
TOUCH-ACTIVATED ELECTRONIC INDUCTION COOKTOP
www.kitchenaid.comThe touch-activated electronic controls offer a variety of heat settings for optimal cooking results. When melting foods such as chocolate or butter, the surface cooking area can be set to the Melt function for minimal cooking power. For maximum surface cooking power, all cooktop touch-activated electronic controls can be set to Performance Boost
Related documents
RISER DIMENSIONS - Harley-Davidson
www.harley-davidson.comRISER DIMENSIONS DESCRIPTION BAR DIAMETER (IN) HEIGHT (IN) PULL BACK (IN) FINISH Road King®, Batwing Touring & Trike 1.00 1.70 0.00 Cast Alum
Thread Dimensions - Goodyear Rubber Products
www.goodyearrubberproducts.comThread Dimensions ODM -- Outside Diameter of the Male IDF -- Inside Diameter of the Female TPI -- Threads Per Inch Note: Female NPT (Tapered Pipe) thread is not available on hose swivel nuts. GHT (3/4") -- 1.0625 ODM, 11-1/2 TPI Normal Engagement Length of NPT Thread in Inches (A) * * Dimensions given do not allow for variations in tapping or ...
IS 14665-1 (2000): Electric Traction Lifts, Part 1 ...
law.resource.orgThe net internal areas are kept as close as possible to those specified in 5.1 of IS 14665 (Part 3/See 1): 2000 and width and depth are generally chosen as modular dimensions in steps of 100 mm. The dimensions given in Table 2 for goods lifts are for normal applications.
Wellness in 8 Dimensions Booklet with Daily Plan
www.center4healthandsdc.orgdimensions are inter-connected. We all know how much they connect in our lives. When we feel financially stressed (e.g., increasing debt), we experience emotional stress (anxiety), sometimes leading to physical problems (illness), less effectiveness at work (occupational), and maybe even questioning our own meaning and purpose in life (spiritual).
FLANGE DIMENSIONS - DIN - ShipServ
cdn1.shipserv.comFLANGE DIMENSIONS - DIN. D = Flange diameter n = Number of bolt holes. Hcd = Hole circle diameter d = Diameter of bolt holes. D = Flange diameter n = Number of bolt holes. ... 65 1.1/2 155 130 15 M12 4 175 140 19 M16 4 175 140 19 M16 8 175 140 19 M16 8 80 3 180 145 19 M16 4 185 150 19 M16 8 200 160 23 M20 8 200 160 23 M20 8 ...
Dimensions of Culture - SAGE Publications Inc
www.sagepub.comDimensions of Culture 161 Table 7.1 Individualism Rankings for 50 Countries and Three Regions 1 United States 2 Australia 3 Great Britain 4/5 Canada 4/5 The Netherlands 6 New Zealand 7 Italy 8 Belgium 9 Denmark 10/11 Sweden 10/11 France 12 Ireland 13 Norway 14 Switzerland 15 Germany (F.R.) 16 South Africa 17 Finland 18 Austria
IS 2102-1 (1993): General tolerances, Part 1: Tolerances ...
law.resource.org4.1 Linear dimensions General tolerances for linear dimensions are given in tables 1 and 2. 1) IS0 8062 : 1904, Castings - System of dimensional tolerances. IS 2102 ( Part 1) : 1993 IS0 2766-l : 1969 4.2 Angular dimensions General tolerances specified in angular units control only the ...