Forward-Curved
Seismic Testing Criteria All Greenheck seismically certified models have been tested using the most severe seismic event that is found on the Spectral Response Map per IBC Figures 1613.5 (1-2). Our testing is performed under the worst-case scenario using the highest mapped seismic load, highest level occupancy category, worst-case
Download Forward-Curved
Information
Domain:
Source:
Link to this page:
Documents from same domain
Minimum 180 in-lb Torque Applications
content.greenheck.comFor damper areas up to 45 sq-ft*(For lower torque, see AF, NFB, LF, ... Time to fit your Specific Application with Belimo’s Flexible Line of ... done in accordance with the damper manufacturer’s specifications. Control is On/Off from an auxiliary contact, or a manual switch. ...
Modular Make-Up Air Unit - content.greenheck.com
content.greenheck.comModular Make-Up Air Unit Model MSX Commercial, Industrial, and Kitchen Applications ... supply air for general, process and combustion exhaust. ... • Airflow Arrangement - Optional Variable Air Volume or Constant Volume 100% Outdoor Air • Performance Range - 800 to 7,500 cfm ...
Heating and Ventilating Units - content.greenheck.com
content.greenheck.com2 Heating Options Hot water, steam and electric heat options are available. The heating section consists of a factory-installed heating coil in a pre-engineered housing.
Energy Recovery and Make-Up Air Start-Up Report
content.greenheck.com5 Condenser Airflow S 6 6 4 8 5 3 4 12 4 1 2 14 13 11 10 9 Supply Airflow P1 P2 T1 T2 Packaged DX Cooling with Digital Scroll Compressor Water-Source Heat Pump with Standard Scroll Compressor
Indirect Gas-Fired Make-Up Air - content.greenheck.com
content.greenheck.com5 Controls Discharge Temperature Control In make-up air units, the unit-controlled heat output is based on discharge temperature. A factory-mounted
High Performance Vane Axial Fans - content.greenheck.com
content.greenheck.comfi 2 Model RA High Performance Vane Axial Fans RA high performance, direct-driven vane axial fans are ideal for inline air ventilation in commercial, institutional or industrial buildings.
Centrifugal Ceiling Exhaust and Inline Cabinet Fans
content.greenheck.com3 Model Comparison Model Location Mounting Airflow Application Drive Type Impeller Type Performance Outdoor Indoor Roof Curb Base/Floor Hanging Wall Ceiling Mounted Exhaust Supply Reversible Recirculate General/Clean Air Contaminated Air Spark Resistant Grease (UL 762) Smoke Control (UL) High Wind (150 mph) High Temp (above 200°F ) Belt Direct Centrifugal Propeller/Axial …
Installation, Operation and Maintenance Manual
content.greenheck.com2 Ceiling Exhaust and Inline Fans ® Typical Installation The ducting from this fan to the outside of the building has a strong effect on the air flow, noise and energy use of
FumeJet Exhaust Systems - content.greenheck.com
content.greenheck.com2 Greenheck’s FumeJet® line of exhaust fans with integral stacks are designed to safely remove and disperse fumes and odors. FumeJet systems replace utility set fans with field supplied intake
Installation, Operation and Maintenance Manual
content.greenheck.comUpblast Centrifugal Roof Exhaust 3 ® When lifting a Belt Drive unit onto the roof, use either the four lifting points on the drive frame or the two lifting
Related documents
Seismic Construction Handbook - Sound Concepts
www.soundconceptscan.comSeismic Design Category The requirements for a suspended ceiling are determined by the buildings Seismic Design Category. Determination of the Seismic Design Category is complex and must be determined by a Registered Architect or Professional Engineer and should be found in the construction docu-mentation.
SEISMIC CEILING INSTALLATION - Armstrong Ceiling S
www.armstrongceilings.comNOTE: Seismic categories are determined for the entire building. This is why the Seismic Design Category information is on the structural drawings. SUMMARY OF IBC SEISMIC INSTALLATION REQUIREMENTS IBC CATEGORY IBC INSTALLATION REQUIREMENTS A, B Ceiling installation should conform to basic minimums established in ASTM C636.
Assembly and Installation Instructions
www.armstrongceilings.com3.1 Non-seismic installation If WoodWorks Grille panels weigh in excess of 2.5 lbs/SF, the ceiling shall be installed per CISCA seismic zones 3-4, as modified by the IBC. WoodWorks Grille slats install perpendicular to the main beams. The main beams shall be spaced 48" O.C. The 48" cross tees shall
SUSPENDED CEILINGS Suspension Systems for Acoustical Lay ...
www.nwcb.org• Seismic splay wires are to be four 12-gauge wires attached to the main beam. Wires are arrayed 90° from each other and at an angle not exceeding 45° from the plane of the ceiling. Source: ASTM E580 Section 5.2.8.2 • Seismic splay wires shall be attached to the grid and to the structure in such a manner that they can support a minimum
Design Manual Keylock Ceiling System - Home | Rondo
www.rondo.com.auinstallation details: • suspended ceilngs: non-fire rated 11 • control joints 14 • external suspended ceiling system 15 • direct fixing of furring channel battens 16 • bulkhead installations 17 bulkheads 18 • curved ceilings 19 • raked & cantilevered ceilings 20 metal ceiling battens domestic 21
USG Exterior Ceiling Systems SYSTEMS GUIDE
www.usg.comthe installation of each USG exterior ceiling system. USG exterior assemblies were tested per UL 580, UL 1897, TAS 202, and TAS 203, and listed in PEI Evaluation Report, PER-12055.
USG Exterior Ceiling Systems Installation Guide (English ...
www.usg.comMark the finished ceiling height and set your laser at 2-1/8 in. above the ceiling height to indicate the top of the U-2-3/32 perimeter molding. Note: For seismic installations, use M20A perimeter molding at the finished ceiling height. Refer to the Seismic Perimeter Applications section in the USG Exterior Ceiling Systems Guide, SC2561. 2-1/8"