Installation Guide - James Hardie
Nails: Ring shank nails of at least 50mm × 2.8mm and diameter head of 6.5mm. These nails should be manufactured according to EN10230-12000. Where 50 × 25mm battens are installed on blockwork, ring shank nails of 2.65 × 30mm, ⌀8mm can be used with hand nailing. Screws: Screws must be a minimum of 35mm long, 4mm diameter shank
Download Installation Guide - James Hardie
Information
Domain:
Source:
Link to this page:
Related documents
INSTRUCTIONS TO LEARN HOW TO USE A LATHE
team358.orgwood or other materials) by causing the workpiece to be held and rotated by the lathe while a tool bit is advanced into the work causing the cutting action. The basic lathe that was designed to cut cylindrical metal stock has been developed further to produce screw threads, tapered work, drilled holes, knurled surfaces, and crankshafts.
DRILLING MACHINES GENERAL INFORMATION
uhv.cheme.cmu.edudrill chucks, while tapered shank drills are usually for the larger drills that need more strength which is provided by the taper socket chucks. TC 9-524 Remove all chuck keys and wrenches before operating. Always wear eye protection while operating any drilling machines. EQUIPMENT Common twist drill sizes range from 0.0135 (wire gage size
Connection and Tension Member Design
faculty-legacy.arch.tamu.eduScrews - Range in sizes from #6 (0.138 in. shank diameter) to #24 (0.372 in. shank diameter) in lengths up to five inches. Like nails, they are best used laterally loaded in side grain rather than in withdrawal from side grain. Withdrawal from end is not permitted. Lag screws (or bolts) – Similar to wood screw, but has a head like a bolt. It ...
LATHES TYPES OF LATHES - Carnegie Mellon University
uhv.cheme.cmu.educollets, drill chucks, tapered shank drills and reamers may be The main feature of its construction are the ways which are inserted into the spindle. Chucks, drive plates, and faceplates formed on its upper surface and run the full length of the bed.may be screwed onto the spindle or clamped onto the spindle nose. 7-3
December 2nd - December 19 OR WHILE STOCK LASTS!
tooltown.caSizes: 3/8” dr. female. 1/4” dr. male 1/2” dr. female. 10-25673 Universal Hub and Drum Puller Maximum bolt pattern 7-1/2” (190.2mm). Includes striking wrench and puller screw and three jaws. 40-89325 114.99 HD Utility Knife Anti-slip rubber grip. Unique cushion handle 27-12330 2.49 SAVE 50% 40-51820 - 10mm 40-51821 - 11mm 40-51822 ...
INTERIOR FINISH OF WALLS AND CEILINGS
www.constructionknowledge.netwood 3/4 inch. Example: 1/2-inch drywall plus 3/4-inch penetration requires a 1 1/4-inch nail. A longer nail does not fasten more securely than one properly sized, and the longer nail is subject to the expansion and contraction of a greater depth of wood. Smooth-shank, diamond-head nails are commonly used to attach two layers of drywall; for ...
HardiePanel Vertical Siding Product Description
www.jameshardiepros.comscrew 1 2 5 1 4d 3mm x 6.8mm x 38mm (0.118 in x 0.267 in x 1.5 in) ring shank siding nail 5 2.3mm x 5.6mm x 38.1mm (0.091 in x 0.221 in x 1.5 in) 13 ET&F 2.5mm x 6.4mm x 38.1mm [AGS-100] (0.100 in x 0.25 in x 1.5 in) 2 3mm x 6.8mm x 50.8mm (0.118 in x 0.267 in x 2 in) 6d Fastening Substrate Approved Fastener Fastening Types wood studs 406mm (16 ...
TECHNICAL DATA SHEET ISSUED BY TIMBER QUEENSLAND ...
www.qbcc.qld.gov.aumm Batten Screw 45 950 75 x 3.15 Galv Flat Head or 75 mm Batten Screw Notes: * Cypress containing sapwood should not be used closer than 250 mm from ground. Refer recommendations in AS 1810. # Where joists are treated softwood, nails shall be deformed ring shank, or alternatively screws.
DOMESTIC DECK DESIGN GUIDE - TasmanKB
www.tasmankb.com.ausoft wood) or 50 mm wide (unseasoned hardwood) are recommended in order to avoid splitti ng when receiving nails or screws from placement of decking boards. This is parti cularly relevant where decking boards abut over the joist as the fi xings can be placed further from the board’s end. Joist sizes can be found in the span Tables 50 in AS1684.