Installation Instructions - Watts
Reduced Pressure Zone Assemblies Reduced Pressure Detector Assemblies Sizes: 21⁄2" – 10" (65 – 250mm) NOTICE For Australia and New Zealand: Pipeline strainers should be installed between the upstream shutoff valve and the inlet of the backflow preventer. It's important that this device be tested periodically in compli-
Download Installation Instructions - Watts
Information
Domain:
Source:
Link to this page:
Documents from same domain
CA-462 Wall Mounted Concealed Arm - Watts Water
media.wattswater.comES-WD-CA-462 USA 0536 CA-462 Tag: CA-462 Wall Mounted Concealed Arm Lavatory Carrier SPECIFICATION: Watts Drainage CA-462 concealed arm lavatory carrier with adjustable epoxy coated cast
TABLE OF CONTENTS - Watts Water
media.wattswater.comFIXTURE CARRIERS CA-461 Wall Mounted Concealed Arm Lavatory w/Back Plate CA-462 Wall Mounted Concealed Arm Lavator CA-481 Wall …
Price List - Watts Water
media.wattswater.comFor the latest Watts pricing information in electronic format, visit our Data Exchange at: • Download product and list price data in .csv, .pdf, .tsv, .xls
Price List - Watts Water Technologies
media.wattswater.com2018 WATTS PRICE LIST Effective July 2, 2018 Price List Water Safety, Flow Control & Backfl ow Prevention Products Watts.com All prices supersede previous issues,
Chemical Resistance of Polypropylene and …
media.wattswater.comBismuth Carbonate 180 Black Liquor 150 Bleach—see Sodium Hypochlorite 12.5 150 Borax, Sodium Borate 180 Boric Acid 180 Brine 180 Bromic Acid NR Bromine Dry NR
FLOOR AND AREA DRAINS - Watts Water …
media.wattswater.comFLOOR AND AREA DRAINS TABLE OF CONTENTS • Pictorial Index • Product Recommendations • Floor Drain Selection Factors Load Rating Grate Free Area
A!' /0# '-'+% D#/'%+ D 0 Installing Drainage …
media.wattswater.comInstalling Drainage Systems Proper installation of Orion drainage sys-tems is extremely important in assuring that installations perform flawlessly for years.
Typical Branch Line - Watts Water
media.wattswater.comSizing and Placement As shown above, it has been established that the preferred location for the water hammer arrestor is at the end of the branch line between
AD F - Welcome Watts Water Technologies
media.wattswater.comES-ACV-F100-F1100 1705 F100 Full Port Ductile Iron Single Chamber Basic Valve SA 0 F 0 Canada 0 00 F 0 0 Watts.ca Latin America 1100100 F 100001 W atts.com 01 AD F * * Contained in Main Valve Repair Kit
Pressure Drop Basics & Valve Sizing - Watts Water
media.wattswater.comWhat Pressure Drop is Not? Pressure drop is pressure loss across the valve created by system demand -NOT by the valve alone.
Related documents
RP/IS-009 Installation, Maintenance, & Repair Series 009 ...
media.wattswater.comsure and reduced pressure zone. Otherwise, such relief (spitting) can occur when the second check is fouled during emergency backflow or resulting from a water hammer condition. For Troubleshooting Guide send for S-TSG. NOTICE Special considerations are necessary when testing assem blies installed on Fire Prevention Systems.
Florida Building Code 6 Edition (2017) Plumbing
www.broward.org312.10.2 Testing. Reduced pressure principle, double check, pressure vacuum breaker, reduced pressure detector fire protection, double check detector fire protection, and spill-resistant vacuum breaker backflow preventer assem-blies and hose connection backflow preventers shall be tested at the time of installation and immediately after
Backflow Preventers and Protection of Water Supply: 2015 IPC
iccsafe.orgfor reduced pressure principle, double check, pressure vacuum, reduced pressure detector fire protection, and spill-resistant vacuum breaker backflow preventer assemblies and hose connection backflow preventers be performed in accordance with one of the following standards: ASSE 5013, ASSE 5015, ASSE 5020, ASSE5047, ASSE 5048,
2015 International Plumbing Code (amended) …
ldh.la.gov312.10.2 Testing. Reduced pressure principle, double check, pressure vacuum breaker, reduced pressure detector fire protection, double check detector fire protection, and spill-resistant vacuum breaker backflow preventer assemblies shall be tested at the time of installation, immediately after repairs or relocation and at least annually.