INTRODUCTION USER’S MANUAL BASIC SAFETY …
In a Multi-level Home: • Install at least one CO Alarm near or within each separate sleeping area. • For added protection, install at least one CO Alarm on each level of the home. • For added protection, install an additional CO Alarm at least 20 feet (6 meters) away from the furnace or fuel burning heat source.
Download INTRODUCTION USER’S MANUAL BASIC SAFETY …
Information
Domain:
Source:
Link to this page:
Documents from same domain
First Alert Talking Combination Smoke and Carbon Monoxide ...
www.firstalertstore.comThis user’s manual contains important information about your Combination Carbon Monoxide & Smoke Alarm’s operation. If you are installing this ... family living units. It is not designed to measure CO levels in ... audible and visual signals for carbon monoxide concentrations under 30 ppm. For additional information on carbon monoxide and ...
USER’S MANUAL INTRODUCTION Smoke & Carbon …
www.firstalertstore.comkeep carbon monoxide or smoke from reaching the Alarm. Installing Smoke/CO Alarms in Mobile Homes For minimum security install one Smoke/CO Alarm as close to each sleeping area as possible. For more security, put one unit in each room. ... (6 meter) distance is not possible – in modular, mobile, or smaller
USER’S MANUAL Smoke Alarms - FirstAlertStore.com
www.firstalertstore.comSmoke Alarms that do not work cannot alert you to a fire. Keep at least one working fire extinguisher on every floor, and an addi-tional one in the kitchen. Have fire escape ladders or other reliable means of escape from an upper floor in case stairs are blocked.
Hardwired Photoelectric Smoke Alarm with Battery Backup
www.firstalertstore.comModel 7010B Only:Activate the battery back-up by removing the “Pull to Activate Battery Back-Up” tab. Or, install battery back-up. Battery back-up cannot work until you install the battery in the correct position (Match “+” to “+” and “-” to “-”). Push and hold test button until the alarm sounds: 3 beeps, pause, 3 beeps ...
USER’S MANUAL Smoke Alarms
www.firstalertstore.com• This Smoke Alarm must have AC or battery power to operate. If the AC power fails, battery back-up will allow the alarm to sound for at least 4 minutes. If AC power fails and the battery is weak, protection should last for up to 7 days. If AC power fails and the battery is dead or missing, the alarm cannot operate.
INSTALLATION HOW TO INSTALL THIS SMOKE/CO ALARM …
www.firstalertstore.comThis Smoke/CO Alarm is designed to be mounted on any standard wiring junction box up to a 4-inch (10 cm) size, on either the ceiling or wall (if allowed by local codes). Read “Where to Install This Alarm” and “Where This Alarm Should Not Be Installed” before you begin installation.
INTRODUCTION USER’S MANUAL FIRE SAFETY TIPS …
www.firstalertstore.com• This Smoke/CO Alarm is approved for use in single-family residences. It is NOT designed for marine or RV use. • This combination Smoke/Carbon Monoxide Alarm has two separate alarms. The CO Alarm is not designed to detect fire or any other gas. It will only indicate the presence of carbon monoxide gas at the sensor.
Related documents
![arXiv:1512.02325v5 [cs.CV] 29 Dec 2016](/cache/preview/8/d/2/3/e/f/c/3/thumb-8d23efc382468588a2c4a27a24325f60.jpg)
arXiv:1512.02325v5 [cs.CV] 29 Dec 2016
arxiv.orgSSD: Single Shot MultiBox Detector Wei Liu1, Dragomir Anguelov2, Dumitru Erhan3, Christian Szegedy3, Scott Reed4, Cheng-Yang Fu 1, Alexander C. Berg 1UNC Chapel Hill 2Zoox Inc. 3Google Inc. 4University of Michigan, Ann-Arbor 1wliu@cs.unc.edu, 2drago@zoox.com, 3fdumitru,szegedyg@google.com, 4reedscot@umich.edu, 1fcyfu,abergg@cs.unc.edu Abstract. …
EAST: An Efficient and Accurate Scene Text Detector
openaccess.thecvf.commulti-scale), 0.7608 on MSRA-TD500 [40] and 0.3945 on 5551. Input Image (a) (b) (c) (d) Multi-channel FCN Multi-orient text-line/word boxes Thresholding ... detector is named as EAST, since it is an Efficient and Accuracy Scene Text detection pipeline. 3.1. Pipeline A high-level overview of our pipeline is illustrated in
MFRC522 Standard performance MIFARE and NTAG frontend
www.nxp.comsoft power-down; RF level detector on [4]-- 10 A IDDD digital supply current pin DVDD; VDDD =3V - 6.5 9 mA IDDA analog supply current pin AVDD; VDDA = 3 V, CommandReg register’s RcvOff bit = 0-7 10mA pin AVDD; receiver switched off; VDDA =3V, CommandReg register’s RcvOff bit = 1-3 5 mA IDD(PVDD) PVDD supply current pin PVDD [5]-- 40mA