INTRODUCTION USER’S MANUAL BASIC SAFETY …
• This CO Alarm should receive continuous 120VAC, 60 Hz, pure sine wave electrical power. Do not use in an extension cord or outlet controlled by a dimmer or switch. • NEVER ignore your Carbon Monoxide Alarm if it alarms. Refer to “If Your CO Alarm Sounds” for more information. Failure to do so can result in injury or death.
Download INTRODUCTION USER’S MANUAL BASIC SAFETY …
Information
Domain:
Source:
Link to this page:
Documents from same domain
First Alert Talking Combination Smoke and Carbon Monoxide ...
www.firstalertstore.comThis user’s manual contains important information about your Combination Carbon Monoxide & Smoke Alarm’s operation. If you are installing this ... family living units. It is not designed to measure CO levels in ... audible and visual signals for carbon monoxide concentrations under 30 ppm. For additional information on carbon monoxide and ...
USER’S MANUAL INTRODUCTION Smoke & Carbon …
www.firstalertstore.comkeep carbon monoxide or smoke from reaching the Alarm. Installing Smoke/CO Alarms in Mobile Homes For minimum security install one Smoke/CO Alarm as close to each sleeping area as possible. For more security, put one unit in each room. ... (6 meter) distance is not possible – in modular, mobile, or smaller
USER’S MANUAL Smoke Alarms - FirstAlertStore.com
www.firstalertstore.comSmoke Alarms that do not work cannot alert you to a fire. Keep at least one working fire extinguisher on every floor, and an addi-tional one in the kitchen. Have fire escape ladders or other reliable means of escape from an upper floor in case stairs are blocked.
Hardwired Photoelectric Smoke Alarm with Battery Backup
www.firstalertstore.comModel 7010B Only:Activate the battery back-up by removing the “Pull to Activate Battery Back-Up” tab. Or, install battery back-up. Battery back-up cannot work until you install the battery in the correct position (Match “+” to “+” and “-” to “-”). Push and hold test button until the alarm sounds: 3 beeps, pause, 3 beeps ...
USER’S MANUAL Smoke Alarms
www.firstalertstore.com• This Smoke Alarm must have AC or battery power to operate. If the AC power fails, battery back-up will allow the alarm to sound for at least 4 minutes. If AC power fails and the battery is weak, protection should last for up to 7 days. If AC power fails and the battery is dead or missing, the alarm cannot operate.
INSTALLATION HOW TO INSTALL THIS SMOKE/CO ALARM …
www.firstalertstore.comThis Smoke/CO Alarm is designed to be mounted on any standard wiring junction box up to a 4-inch (10 cm) size, on either the ceiling or wall (if allowed by local codes). Read “Where to Install This Alarm” and “Where This Alarm Should Not Be Installed” before you begin installation.
INTRODUCTION USER’S MANUAL FIRE SAFETY TIPS …
www.firstalertstore.com• This Smoke/CO Alarm is approved for use in single-family residences. It is NOT designed for marine or RV use. • This combination Smoke/Carbon Monoxide Alarm has two separate alarms. The CO Alarm is not designed to detect fire or any other gas. It will only indicate the presence of carbon monoxide gas at the sensor.
Related documents
DC to AC Converters Inverters - Engineering
www.site.uottawa.caDesign Constraints of a Pure Sine wave Inverter Quantity Details Voltage Convert 12VDC to 120 VAC Power Provide 300 W continuous Efficiency > 90% efficiency Waveform Pure 60 Hz sinusoidal Total Harmonic Distortion < 5% THD Physical Dimensions 8” x …
Trigonometric Fourier Series - University of North ...
people.uncw.eduWe can easily add shifted sine functions. In Figure 3.4 we show the functions y(t) = 2sin(4pt) and y(t) = 2sin(4pt + 7p/8) and their sum. Note that this shifted sine function can be written as y(t) = 2sin(4p(t + 7/32)). Thus, this corresponds to a time shift of 7/32. So, we should account for shifted sine functions in the general sum. Of
DC/AC Pure Sine Wave Inverter
web.wpi.eduoutput generated: modified sine wave, and pure sine wave1. A modified sine wave can be seen as more of a square wave than a sine wave; it passes the high DC voltage for specified amounts of time so that the average power and rms voltage are the same as if it were a sine wave.
Signal Types and Terminations - Vectron
www.vectron.comMost logic output sources are derived form a sine or clipped sine wave source which degrades the phase noise performance - a sine-wave output is the ideal for demanding low phase noise applications. Clipped sinewaves are formed by limiting a sinewave output, ‘squaring off’ the wave at its maximum and minimum extent.
PICkit 3 Programmer/Debugger User's Guide
ww1.microchip.comJan 02, 2008 · PICkit™ 3 USER’S GUIDE © 2009 Microchip Technology Inc. DS51795A-page iii Table of Contents Preface .....1
Bound States in One Dimension - University of Illinois ...
courses.physics.illinois.eduthe wave function vanishes outside the box, it must vanish on the walls of the box atx =0andx = a. Since we know that the wave function is comprised of sinusoidal functions we are searching for a wave function with a nodes at x =0 and x = a. Only a pure sine function has a node at the origin. The distance between nodes of a sinusoidal function ...
2100½-Digit USB Digital Multimeter6 - Tektronix
download.tek.comb . Pure sine wave input greater than 5% of range . 2 . 750VAC range is limited to 100kHz . GENEral AC CMRR: 70dB (for 1kW unbalance LO lead) . POWER SUPPLy: 120V/220V/240V . POWER LINE FREQUENCy: 50/60Hz auto detected . POWER CONSUMPTION: 25VA max . DIGITAL I/O INTERFACE: USB-compatible Type B connection . ENVIRONMENT: For indoor …