McWANE DUCTILE IRON PIPE
visit pe.mcwane.com for more information All Dimensions are in Inches. ... When laying a pipe or fitting in a trench, orient the locking segment insertion bell slots so that: The 2 slots on 4" - 20" pipe are at the horizontal or 3 and 9 o'clock positions 4 ...
Download McWANE DUCTILE IRON PIPE
Information
Domain:
Source:
Link to this page:
Documents from same domain
FLANGED AND MECHANICAL JOINT WALL PIPE …
www.mcwaneductile.com75 FLANGED AND MECHANICAL JOINT WALL PIPE (Fabricated)* (AWWA C111) Flange and Plain End Flange and Flange Flange and MJ MJ and MJ Plain End and MJ
PACIFIC STATES CAST IRON PIPE COMPANY
www.mcwaneductile.comA Division of McWane, Inc. General Offi ces and Plant 801-373-6910 Telephone 801-377-0338 Facsimile Mailing Address: Street Address: P.O. Box 1219 1401 East 2000 South Provo, Utah 84603 Provo, Utah 84606 Website www.pscipco.com For local contact information please visit our website.
MCWANE, INC. RANSOM INDUSTRIES, INC.
www.mcwaneductile.comMCWANE, INC. DIVISION OFFICES The several divisions of McWane, Inc. have sales representatives and distributors in principal cities. Contact the General …
DUCTILE IRON FLANGED FITTINGS - mcwaneductile.com
www.mcwaneductile.com56 DUCTILE IRON FLANGED FITTINGS ANSI/AWWA-C110/A21.10 Standard REDUCING ELBOWS Furnished Faced and Drilled to 125 Pound Template Unless Otherwise Ordered.
GUIDELINES Installation Guide for Ductile Iron Pipe
www.mcwaneductile.comDuctile Iron Pipe is substantially more resistant to damage from impact or concentrated stress. Although both materials are classified as cast irons, in today’s terminology, the older material is identified as gray iron and the newer material as Ductile Iron. During the solidification stage
MCWANE DUCTILE IRON PIPE
www.mcwaneductile.com13. ®Do not use SURE STOP 350 GASKETS with thick coating on the pipe exterior. 14. 20If SURE STOP 350® GASKETS are used in straight casings, you must pull the pipe through the casing. Do not push the pipe. Size In. Rating psi Deflection Degrees 3 350 5 4 350 5 6 350 5 8 350 5 10 350 5 12 350 5 14 350 4 16 350 4 18 350 4 20 350 2.5 24 350 2.5
2” - 36” MECHANICAL JOINT - DUCTILE IRON FULL BODY …
www.mcwaneductile.comFULL BODY FITTINGS Manufactured in Accordance With ANSI/AWWA C-110/A21.10 and ANSI/AWWA C111/A21.11 Standard Full Body Mechanical Joint Fittings Straight Tees and MJxMJxPE Bullhead Reducing on Branch Tees (available in MJ or Flange only) Notice: Weights published in this catalog are for shipping purpose only. Actual weights may vary because
FLANGED AND MECHANICAL JOINT WALL PIPE (Fabricated)*
www.mcwaneductile.comFLANGED AND MECHANICAL JOINT WALL PIPE (Cast)* (AWWA C111) Flange and Plain End Flange and Flange Flange and MJ MJ and MJ Plain End and MJ *Wall pipe can be furnished in varied lengths. Check for minimum and maximum available length. Note: Order must specify if plain end is to socket in a Mechanical Joint or Push-on bell.
Related documents
HDPE (4710) - National Pipe
nationalpipe.comHDPE (4710) HDPE 4710 IPS & DIPS PRESSURE PIPE (8, 10”) Scope: This submittal designates the general requirements for High Density Poly-Ethylene Pressure Pipe from compound with a cell classification PE345464C as defined in ASTM Standard D-3350. Pipe: All pipe is manufactured in accordance with the specifications set-forth in AWWA C906 “Standard …
DESIGN AND SELECTION OF PLASTIC PRESSURE PIPE …
www.hdpe.caThe reduction in working pressure of a PVC pipe below its’ pressure class increases as the flow velocity increases. At 7.5 fps the working pressure of the PVC pipe is less than that of the PE pipe. A graphical depiction of the flow rate (usgpm) and the hydraulic loss for 12” DIPS DR18 PVC and 12” DIPS DR17
INEOS Environmental Stress Crack Resistance of PE
www.ineos.comincreasingly discussed in the European PE pipe industry, to the point of establishing material specifications prior to offering a detailed description of the test method. This method is diagrammed in Figure 4. Typical test specimens measure 10 x 10 x 100 mm and are machined directly from pipe or from a molded plaque.
SECTION 20 HORIZONTAL DIRECTIONAL DRILLING …
www.mawss.comconformance with the pipe manufacturer’s recommendations. Joining, laying, and pulling of polyethylene pipe shall be accomplished by personnel experienced in working with polyethylene pipe. The pipe supplier shall certify in writing that the Contractor is qualified to join, lay, and pull the pipe or representative of the pipe
Chapter 14 - Duct and Conduit - plastic pipe
plasticpipe.orgASTM D2447 - Standard Specification for Polyethylene (PE) Plastic Pipe, Schedules 40and 80, Based on Outside Diameter (Withdrawn 2010) 14 - 6 Chapter 14 Duct and Conduit (HDPE) Conduit Based on Controlled Outside Diameter (OD) for both power and telecommunications.