Padmount Transformers - Location Guidelines
Barriers If the clearances specified above cannot be adhered to, a fire resistive barrier may be constructed by the builder or developer in lieu of the separation specified. The barrier shall extend to a projection line from the corner of the transformer to the farthest corner of the wall, opening, or patio necessary to satisfy minimum distance.
Download Padmount Transformers - Location Guidelines
Information
Domain:
Source:
Link to this page:
Documents from same domain
Application for Combined Heat and Power Incentives - PECO
www.peco.comfacilitate the installation of combined heat and power (CHP) systems as an approved energy efficiency program measure. This program is open to PECO account holder …
Section 8 - Metering - PECO
www.peco.comduring design. equipment in Approved • Use of ganged order to ensure indoor ganged meters may change sufficient RF meter location the installation, communications. maintenance, and ownership responsibilities of some facilities. These particulars should be discussed and understood by the builder prior to construction.
NOTE: THE BLANK FORM IS BELOW THE SAMPLE FORM Note ...
www.peco.comPHILADELPHIA COUNTY 830 S. Schuylkill Ave. Philadelphia, PA 19146 Email:PhilaNewBusiness@e xeloncorp.com Fax # (215) 731-2327 DELAWARE & CHESTER COUNTIES 1050 W. Swedesford Rd. Berwyn, PA 19312 Email:DelChesterServiceApplications@ex eloncorp.com Fax # (610) 725-1416 BUCKS & …
12. ILLUSTRATIONS 12.1 GENERAL - PECO Energy Company
www.peco.com12. ILLUSTRATIONS . 12.1 . GENERAL . Illustrations of typical service equipment and installations are shown in this section as an aid to interpretation …
Supplement No. 1 to ELECTRIC PA P.U.C NO. 7 SUPERCEDES ...
www.peco.comTariff Electric Pa. P.U.C. No. 7 PECO Energy Company Original Page No. 1A APPLICABILITY INDEX OF RIDERS - Original Page No. 73 – Added a footnote to the Construction Rider which expands the applicability to Rate GS customers with demands greater than 500 kW.
11. CABLE SPECIFICATIONS 5kV, 15kV, AND 35kV RUBBER …
www.peco.comTyco/Raychem Corp. HVT352 (Indoor), HVT352S (Outdoor) 750 kcmil, 35 kV CONCENTRIC NEUTRAL CABLE Manufacturer Trade Name 3-M Manufacturing Co. Quick Term III, 7655-S-4 Quick Term III, 7656-S-4 Tyco/Raychem Corp HVT353 (Indoor), HVT353S (Outdoor) Cable Specifications Rev-5 August 2008 Page 8 of 10
Related documents
Technical Guide: DensGlass® Sheathing
floridabuilding.orgitself. Consult with the local building code, design professional, owner or cladding manufacturer for water-resistive barrier requirements. DensGlass Sheathing is the ideal substrate for a wide variety of air and water-resistive barriers including building wraps, liquid applied coatings and self-adhering membranes. See page 9 for details.
HARDIPLANK Installation Instructions
www.structuretech1.comresistive barriers with all siding products. James Hardie will assume no responsibility for water infiltration within the wall. HANDLING & STORAGE: Store flat and keep dry prior to installation. Installing siding wet or saturated may result in shrinkage at butt joints. Carry planks on edge. 1” from plank top stud
TECHNICAL GUIDE - Georgia-Pacific Building Products
www.buildgp.comDensGlass Sheathing is the ideal substrate for a wide variety of air and water-resistive barriers including building wraps, fluid applied coatings, self-adhering membranes and spray foam applications. See page 10 for details. Easy to Handle DensGlass Sheathing is lightweight and easy to handle. It can be cut and fastened with standard drywall ...
HardieTrim Boards - Installation Instructions
www.buildsite.comresistive barrier figure 1 effective september 2019 hardietrim ® boards important: failure to follow james hardie written installation instructions and comply with applicable building codes may violate local laws, affect building envelope performance and may affect warranty coverage.
DuPont Tyvek Water-Resistive and Air Barriers Residing ...
www.dupont.comFlexible Sheet Water-Resistive Barriers Intended for Mechanical Attachment Air leakage control and air barriers are required in the IECC-2015 Sections R402.4 and C402.4. Specifically, Section C402.5 identifies three compliance options for air barriers. DuPont™ Tyvek ® WRBs comply with the option detailed in Section C402.5.1.2.1:
DuPont Performance Building Solutions Air Barrier ...
www.dupont.comDuPont™ Tyvek® Water-Resistive and Air Barriers Installation Guidelines For Buildings Less Than 5 Stories and Low-Rise Multi-Family Residential Buildings Less Than 6 Stories. Key Considerations • Use > 1/4 inch bead of DuPont™ Residential Sealant. • Use J-Roller or firm hand pressure over sealant interface to
Vapor Retarder Classification - Energy
www.energy.govVapor barriers have traditionally been installed on the warm in winter side of the wall assembly in an attempt to keep interior moisture from entering the wall cavity ... 1.inyl lap or horizontal aluminum siding applied over a weather-resistive barrier V
NO CAULK - James Hardie
www.jameshardie.comcoated coil stock and code compliant water-resistive barriers, such as HardieWrap® weather barrier. Other products may also be suitable. James Hardie DOES NOT recommend using caulk or “H”-jointers for the butt joints of HardiePlank ® siding with ColorPlus® technology.
HARDIPLANK Installation Instructions
www.structuretech1.comresistive barriers with all siding products. James Hardie will assume no responsibility for water infiltration within the wall. HANDLING & STORAGE: Store flat and keep dry prior to installation. Installing siding wet or saturated may result in shrinkage at butt joints. Carry planks on edge. 1” from plank top stud
Window Rough Opening Prep and Flashing - Marvin
www3.marvin.comCutting the Weather Resistive Barrier (WRB) and Pan Flashing NOTE: This does not apply to self-adhering WRB sheathing systems. 1.Make horizontal cuts to the Weather Resistive Barrier (WRB) across the top and bottom of the Rough Opening. Make a vertical cut down the center of the RO. then make 45 degree cuts away from the corners of the top of ...